HRXD9, HRXD16 9-, 16-Channel Models Digital Video Recorder User Guide Document 900.
Revisions Issue Date Revisions 1.00 12/06 New document. 2.00 10/07 Manual updated for the latest software release. 3.00 11/07 Minor changes and corrections. A 01/08 Add DVD-RW to the manual (specifications and other places). B 02/08 Added a Caution to the "Connecting the Power Cord" section of the Installation chapter.
FCC Compliance Statement INFORMATION TO THE USER: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Compliance WEEE (Waste Electrical and Electronic Equipment) Correct Disposal of this Product (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
Contents Contents FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Explanation of Graphical Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Overview of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Shutdown Screen . . . . Logout Screen . . . . . Network and Notification Setup . Network Screen . . . . . LAN Setup Screen . . . Modem Setup . . . . . . DVRNS Setup . . . . . . WebGuard Setup . . . . Notification Setup . . . . Configuring Devices . . . . . . . Camera Setup Screen . Audio Setup Screen . . Alarm-Out Screen . . . . Display Screen . . . . . Remote Control Screen. Recording Settings . . . . . . . . Record Screen . . . . . Schedule Screen . . . . Pre-Event Screen . . . . Archive Screen .
Contents Go to the Date/Time . Calendar Search. . . Event Log Search . . Text-In Search . . . . Motion Search . . . . Clip-Copy Screen . . Print Screen . . . . . Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 8
Figures Figures Figure 1-1 Typical DVR Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 2-1 16-Channel DVR Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 2-2 Video Input Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 2-3 Video Loop-Through Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 2-4 Video Out Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures Figure 3-16 10 Device Information Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 3-17 Storage Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Figure 3-18 User Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Figure 3-19 New Group Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Figure 3-20 New User Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures Figure 3-59 Motion Detection Settings Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Figure 3-60 Motion Detection Sensitivity Screen . . . . . . . . . . . . . . . . . . . . . . . . . 79 Figure 3-61 Motion Detection Min. Blocks Screen . . . . . . . . . . . . . . . . . . . . . . . . 79 Figure 3-62 Motion Detection Zone Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Figure 3-63 Motion Detection Zone Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures Figure B-1 12 Text-In Search Option Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . .124 Figure B-2 Text-In Search Option Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . .125 Figure C-1 Clip Player Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Figure D-1 WebGuard Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Figure D-2 WebGuard Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Document This document introduces the HRXD Series Digital Video Recorder (DVR) and describes how to install, configure, and operate the DVR. This guide covers the 9- and 16-channel HRXD Series DVRs. The DVRs are identical except for the number of cameras and alarms that can be connected and the number of cameras that can be displayed. For simplicity, the illustrations and descriptions in this guide refer to the 16-camera model.
• • • • Appendix H, Map of Screens, provides a graphical illustration of the menu screens. Appendix I, System Log Notices, lists all of the System Log notices. Appendix J, Error Code Notices, lists the system upgrade and clip copy Error Code notices. Appendix K, Specifications, lists the DVR specifications. Important Safeguards 1. Read Instructions All the safety and operating instructions should be read before the appliance is operated. 2.
8. Power Cords Operator or installer must remove power, BNC, alarm, and other connections before moving the equipment. 9. Lightning For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment due to lightning and power-line surges. 10.
17. Correct Batteries WARNING! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 18. Operating Temperature An operating temperature range is specified (see Appendix K, Specifications) so that the customer and installer may determine a suitable operating environment for the equipment. 19.
Introduction 1 Introduction Features Your color digital video recorder (DVR) provides recording capabilities for nine or 16 camera inputs.
Introduction Technical Overview In addition to replacing both a time-lapse VCR and a multiplexer in a security installation, your DVR has many features that make it much more powerful and easier to use than even the most advanced VCR. The DVR converts analog NTSC or PAL video to digital images and records them on a hard disk drive. Using a hard disk drive allows you to access recorded video almost instantaneously; there is no need to rewind tape.
Introduction Figure 1-1 Typical DVR Installation Computer Screen (VGA) Spot Monitor x4 Sensor 9 or 16 Alarm Input 9 or 16 Cameras Siren Video Out Audio Input x4 Alarm Output 9 or 16 Audio Output Digital Video Recorder LAN or MODEM Network Connection Flashing Light Internal CD-RW or DVD-RW External SCSI Hard Disk Drive USB Device x 3 Document 900.
Introduction 20
Installation 2 Installation Package Contents The package contains the following: • • • • • • • • • • • Digital Video Recorder Power cord User Guide (this document) Multilingual User Guide (RASplus CD-ROM) RASplus User Guide Multilingual RASplus Software CD and User Guide (RASplus CD-ROM) DVRNS Server Software and User Guide (RASplus CD-ROM) Rack-mount kit Assembly screws guide rails for adding Hard Disk drives Screws for attaching SCSI connector Infrared remote control Required Installation Tools No spe
Installation Figure 2-1 16-Channel DVR Rear Panel SVHS Out Video In Power Connector Audio In/Out Spot Out Video Out USB Port Alarm Inputs RS232 Port SCSI Port VGA Port Factory Reset Switch RS485 Ethernet Port Alarm Reset In Alarm Outs Your DVR can be used with either NTSC or PAL equipment. Note You cannot mix NTSC and PAL equipment. For example, you cannot use a PAL camera and an NTSC monitor.
Installation If you would like to connect your video source to another device, you can use the Loop BNC connectors. Note The Loop BNC connectors are auto terminated. Do NOT connect a cable to the Loop BNC unless it is connected to a terminated device because it will cause poor quality video. Connecting the Monitor Figure 2-4 Video Out Connectors Connect the main monitor to either the Video Out or SVHS Out connector.
Installation Connecting a VGA Monitor Figure 2-5 VGA Connector A VGA connector is provided so that you can use a standard, multi-sync computer monitor as your main monitor. Use the cable supplied with your monitor to connect it to the DVR. Note Caution Pressing and holding DISPLAY on the front panel for 5 seconds or longer will switch the video output between Video Out (BNC or SVHS Out) and VGA Out. During clip copy, you cannot switch the video output between Video Out and VGA Out.
Installation Your DVR can record audio from up to four sources. Connect the audio sources to Audio In 1, Audio In 2, Audio In 3 and Audio In 4 as needed using RCA jacks. Connect Audio Out to your amplifier. Note The DVR does not have amplified audio output, so you will need a speaker with an amplifier. The DVR does not have a pre-amplifier for audio input, so the audio input should be from an amplified source, not directly from a microphone.
Installation GND (Ground) Note All the connectors marked GND are common. Connect the ground side of the alarm input and/or alarm output to the GND connector. AO 1 to 16 (Alarm-Out) Figure 2-8 Alarm Output Connectors The DVR can activate external devices such as buzzers or lights. Connect the device to the AO (Alarm-Out) and GND (Ground) connectors. AO is an active low open collector output which sinks 5 mA@12V and 30 mA@5V. See Chapter 3, Configuration for configuring alarm outputs.
Installation Connecting to the RS485 Port Figure 2-10 RS485 Connector The DVR can be controlled remotely by an external device or control system, such as a control keyboard, using RS485 half-duplex serial communications signals. The RS485 connector can also be used to control PTZ (pan, tilt, zoom) cameras. Connect RX-/TXand RX+/TX+ of the control system to the - and + (respectively) of the DVR.
Installation Connecting to the RS232 Port Figure 2-13 RS232 Connector An RS232 port is provided to connect an external modem for remote monitoring, configuration and software upgrades, and to connect a remote control keyboard. Use a modem cable with a DB-9S (female) connector to connect to the DVR. See Chapter 3, Configuration for configuring the modem. Note The DVR is not supplied with a modem cable, and many modems are not supplied with cables.
Installation Caution Do NOT connect or disconnect SCSI devices while the DVR power is on. The DVR must be powered down to connect or disconnect SCSI devices. Power up SCSI devices so they are ready for operation before powering up the DVR. Power down SCSI devices after powering down the DVR and then disconnect SCSI devices. Caution If the SCSI device is shut down while the device is operating, the DVR system might not operate normally.
Installation Factory Reset Figure 2-16 Factory Reset Switch The DVR has a Factory Reset switch to the left of the USB port on the rear panel. This switch will only be used on the rare occasions that you want to return all the settings to the original factory settings. Caution When using the Factory Reset, you will lose any settings you have saved. To reset the unit, you will need a straightened paperclip: 1. Turn the DVR off. 2. Turn it on again. 3.
Installation Connecting the Power Cord Figure 2-17 Power Cord Connector Connect the AC power cord to the DVR and then to a wall outlet. WARNING! Caution ROUTE POWER CORDS SO THAT THEY ARE NOT A TRIPPING HAZARD. MAKE CERTAIN THE POWER CORD WILL NOT BE PINCHED OR ABRADED BY FURNITURE. DO NOT INSTALL POWER CORDS UNDER RUGS OR CARPET. THE POWER CORD HAS A GROUNDING PIN. IF YOUR POWER OUTLET DOES NOT HAVE A GROUNDING PIN RECEPTACLE, DO NOT MODIFY THE PLUG.
Installation 32
Configuration 3 Configuration Note Your DVR should be completely installed before proceeding. Refer to Chapter 2, Installation. Front Panel Controls Figure 3-1 16-Channel DVR Front Panel Camera Internal CD-RW or DVD-RW USB Display Freeze Sequence Menu Search Spot Zoom Alarm LEDs PTZ Play/Pause Panic Enter RW Forward Shuttle Ring FF Jog Dial Arrow Buttons Backward The front panel looks and operates much like a VCR combined with a multiplexer. Many of the buttons have multiple functions.
Configuration Note The infrared sensor on the DVR is just to the left of the arrow buttons. Make certain that nothing blocks the sensor, or the remote control will not function properly. Note You can also use a USB mouse (not supplied) to navigate through the screens and menus much like you would on a computer.
Configuration Note Table 3-1 Some buttons on the infrared remote control may not be supported, depending on the DVR model. Front Panel Buttons and Controls Control Description Camera Buttons (1 to 16) Pressing the individual camera buttons will cause the selected camera to display full screen. Buttons 1 to 9 are also used to enter passwords. DISPLAY Button The DISPLAY button has two functions. First, it toggles between different display formats. The available formats are: 4x4, 3x3, 2x2 and PIP.
Configuration Table 3-1 Front Panel Buttons and Controls (cont’d) Control Description HDD LED The HDD LED flickers when the DVR is recording or searching video on the hard disk drive. NETWORK LED The NETWORK LED flickers when the unit is connected to a network via either Ethernet or modem. POWER LED The POWER LED is lit when the unit is On. Enter Button The (Enter) button selects a highlighted item or completes an entry that you have made during system setup.
Configuration Table 3-1 Front Panel Buttons and Controls (cont’d) Control Description Jog Dial When in playback mode, you can play video forward image-by-image by turning the Jog Dial clockwise and backward image-by-image by turning the Jog Dial counterclockwise. When in PIP mode, you can make the PIP screen smaller by turning the Jog Dial clockwise and larger by turning the Jog Dial counterclockwise.
Configuration Figure 3-3 Login Screen Select a User and enter the password by pressing the appropriate combination of Camera number buttons and then . There is no default password when logging in the admin user for the first time. Note To assure the secure management of the system, setting up a password is strongly recommended. Note You can use a mouse (not supplied) to access the Login screen in addition to using the front panel buttons or the infrared remote control.
Configuration Press MENU to enter the setup screen. While setting up the DVR, there will be many opportunities to enter names and titles. When making these entries, a Virtual Keyboard will appear. Figure 3-5 Virtual Keyboard Use the arrow keys to highlight the character you want in the name or title and press . That character appears in the title bar and the cursor moves to the next position. Pressing toggles between the upper and lower case keyboards, backspaces, and deletes entered characters.
Configuration 2. Highlight the Site box and press to enter a Site Name. 3. Once you have entered your title, highlight OK and press 4. Highlight the box beside System ID and press . Change the number by highlighting it and using the Up and Down arrow buttons to increase and decrease the number from 0 to 99. Note . A virtual keyboard appears that you can use . The System ID number is used to identify the unit when it is connected with other DVRs through the RS485 port.
Configuration Caution 7. The USB device must be FAT16 or FAT32 format. You can import saved DVR settings or export the current DVR settings. To import saved DVR settings: a. Connect the USB device containing the setup file (.dat) to the DVR. b. Highlight Setup – Import… and press c. Select the desired setup file and press Import to import the selected settings and change the DVR settings accordingly. d. Highlight Include Network Setup and press to toggle between On and Off.
Configuration Figure 3-10 System Log Screen The System Log screen lists system activities (up to 5,000 from the latest activity) that have occurred along with the time and date. The icon will be displayed in the last column for system activities of the remote site. You can scroll through the log pages by using the Up and Down arrows, or you can go directly to a log page by entering the log page number in the box at the bottom-left of the screen. Highlight Close and press to exit the screen. 10.
Configuration Figure 3-11 Date/Time Setup Screen 2. Highlight the first box beside Date and press . The individual sections of the date will highlight. Use the Up and Down arrow buttons to change the number. Use the Left and Right arrow buttons to move between month, date and year. Once you have the correct date, press . 3. Highlight the Format box beside Date and press . Select from the three available date formats and press to save your selected format. 4.
Configuration Figure 3-12 9. Holiday Setup Screen You can set up holidays by highlighting + and pressing appears. . The current date 10. Highlight the month and day and change them by using the Up and Down arrow buttons. Press to add the date. Dates can be deleted by highlighting beside the date and pressing . Note Holidays that do not fall on the same date each year should be updated once the current year’s holiday has passed. 11.
Configuration Note You can use the domain name instead of an IP address if you already set up the DVRNS Server when setting up the LAN. 14. Highlight the box beside Interval and press . Set the time interval for synchronization from 30 minutes to 1 day at various time intervals. Last Sync-Time displays the last time the DVR was synchronized with the time server. 15. Highlight Run as Server and press . Pressing toggles between On and Off.
Configuration Figure 3-15 Device Format Screen Note A USB hard disk drive can be formatted and used only for archiving. Note The DVR does NOT support USB hard disk drives with a version lower than 2.0. Note System upgrades require formatting internal hard disk drives, so do not uninstall internal hard disk drives even though they are not used for either recording or archiving; for example, when using only external SCSI hard disk drives.
Configuration Note Caution 6. When disconnecting a USB hard disk drive from the DVR, highlight Don’t Use first and then disconnect the device. Do NOT disconnect the USB cable or the power from the device while copying video clips. If the USB cable is disconnected while copying video clips, archived data might be lost. Highlight the Status tab, and the Storage Status screen (Figure 3-17) displays. Figure 3-17 Storage Status Screen The Type column displays the type of storage device.
Configuration Note 7. Temperature and S.M.A.R.T. information will be available only for IDE hard disk drives supporting the SMART (Self-Monitoring Analysis and Reporting Technology) monitoring program. Selecting Close and pressing exits the screen. User Setup Screen 1. Highlight User in the System menu and press . The User setup screen (Figure 3-18) displays the authorized groups and users. You can add and delete groups and users. When adding a group, you can assign authority levels to the group.
Configuration 4. Highlighting a User Name and pressing allows you to add or change the password assigned to that user. You can also change the group to which the user is assigned. 5. The column can be used to delete a User Name or an entire Group. If the is grayed out, that Group or User cannot be deleted. Highlight the and press . You will be asked to confirm that you want to delete the User or Group.
Configuration • • • • 8. System Check — The user can view the remote system status or check the remote system status as a batch process on a PC running RAS. Record Setup — The user can establish all Record settings on a local system or a PC running RAS. Search — The user can access Search mode on a local system or a PC running RAS. Clip-Copy — The user can copy video clips on a local system or a PC running RAS, and save video data in an AVI, bitmap or JPEG file format.
Configuration Figure 3-21 Shutdown Screen After selecting Shutdown and pressing safe to disconnect power. , a screen will appear telling you when it is Logout Screen Highlight Logout in the System menu and press . The Logout screen displays asking you to confirm whether or not you want to log out the current user. Figure 3-22 Logout Screen After selecting Logout and pressing , the user will be logged out.
Configuration Figure 3-24 Network Setup Screen 2. Highlight the first box beside Transfer Speed. Press the Up and Down arrow buttons to set the Transfer Speed from 50 Kbps to 100 Mbps. 3. Highlight the second box beside Transfer Speed. You can select the unit of measure for the transfer speed between: bps and ips. Press to set the transfer speed. 4. Highlight the box beside Quality and press Very High, High, Standard and Low. Press . You can select the Quality from: to set the Quality.
Configuration Figure 3-25 LAN (Manual) Setup Screen 2. Highlight the box beside Type and press . You can select the type of network configuration from: Manual, DHCP and ADSL (with PPPoE). Select the desired type and press . 3. Selecting Manual as the Type allows you to set up LAN parameters manually. Note a. You will need to get the appropriate IP Address, Gateway and Subnet Mask values from your network administrator.
Configuration Figure 3-26 d. Port Numbers Setup Screen Change the numbers by highlighting them and using the Up and Down arrow buttons to increase or decrease the number. The factory default Port settings are: Caution 4. 54 Remote Admin: 8200 Remote Callback: 8201 Remote Watch: 8016 Remote Search: 10019 Note The system restarts automatically after changing the port settings.
Configuration Figure 3-27 5. LAN (DHCP) Setup Screen Selecting ADSL (with PPPoE) allows you to set up the ADSL network. Note ADSL and modem cannot be configured at the same time. If the DVR is configured by modem, the ADSL (with PPPoE) will not be selected. Figure 3-28 LAN (ADSL) Setup Screen a. Highlight the box beside ID and press . A virtual keyboard appears allowing you to enter the ID for ADSL connection. b. Highlight the box beside Password and press .
Configuration Note If the DVR is configured for DHCP or an ADSL network, the DVR’s IP address might change whenever the unit is turned on. Modem Setup 1. Highlight the Modem tab, and the Modem screen (Figure 3-29) displays. Figure 3-29 Note 56 Modem Setup Screen If the RS232 port is in use for remote control, networking cannot be configured for a modem. 2. Highlight Enable and press to toggle between On and Off. You will only be able to change the settings if Modem is enabled. 3.
Configuration DVRNS Setup 1. Highlight the DVRNS tab, and the DVRNS screen (Figure 3-30) displays. Figure 3-30 Note 2. When LAN settings have been changed, set up the DVRNS after saving your LAN changes by highlighting Save and pressing . Highlight Use DVR Name Service and press Note 3. DVRNS Setup Screen to toggle between On and Off. The DVRNS (DVR Name Service) allows the DVR to use Dynamic IP addresses for remote connection.
Configuration Note You can use the domain name instead of IP address if you already set up the DNS Server when setting up the LAN. 4. Highlight the box beside Port and press . Set the port number of the DVRNS server using the Up and Down arrow buttons to increase or decrease the numbers. 5. Highlight Use NAT and press Note to toggle between On and Off. When using the NAT (Network Address Translation) device, refer to the NAT manufacturer’s instructions for the proper network settings. 6.
Configuration Figure 3-31 WebGuard Setup Screen 2. Highlight Use WebGuard Service and press to toggle between On and Off. See Appendix D, WebGuard for detailed descriptions of the WebGuard service. 3. Highlight the box beside Port and press . Set the port number used when accessing WebGuard by using the Up and Down arrow buttons to increase or decrease the numbers. 4. You can save your Network changes by highlighting Save and pressing Selecting Cancel exits the screen without saving the changes. .
Configuration 3. Highlight the box beside SMTP Server and press . Use the virtual keyboard that appears to enter the IP address or domain name of the SMTP server. Note You will need to get the IP address or domain name of the SMTP Server from your network administrator. Note You can use the domain name instead of IP address if you already set up the DNS Server when setting up the LAN. 4. Highlight the box beside Port and press .
Configuration Figure 3-34 Notification Callback Setup Screen 10. Highlight LAN and press to toggle between On and Off. When LAN is turned On you can change the IP addresses. 11. Highlight the IP Address box that you want to change and press . Enter the IP address of the computer you want contacted during an event. You can enter up to five IP addresses. 12. Highlight the box beside Retry and enter the number of times you would like the DVR to try contacting the computer(s).
Configuration Figure 3-35 Device Menu Camera Setup Screen 1. Highlight Camera in the Devices menu and press (Figure 3-36) appears. Figure 3-36 Camera Setup Screen 2. You can turn the camera number On or Off, and you can change the Title of each camera using the virtual keyboard. 3. You can also determine which cameras will display on the monitors by selecting Normal, Covert 1 or Covert 2 from a drop-down list in the Use column. 4. 62 .
Configuration Figure 3-37 Note Camera PTZ Setup Screen You will only be able to set up PTZ devices if the PTZ port is set to RS232 or RS485. You will not be able to use a modem if you are using the RS232 port for PTZ control. 5. Highlight the box in the Product column for the PTZ camera you wish to configure and press . A list of PTZ devices appears. 6. Select your camera from the list and press .
Configuration Figure 3-39 9. Port Setup Window Configure the port’s setting based on the PTZ camera manufacturer’s instructions. 10. You can save your Camera changes by highlighting Save and pressing Selecting Cancel exits the screen without saving the changes. . Audio Setup Screen 1. Highlight Audio in the Devices menu and press (Figure 3-40) appears. Figure 3-40 Audio Setup Screen 2. The DVR can record up to four audio inputs. Highlight the box beside the input and press .
Configuration Alarm-Out Screen 1. Highlight Alarm-Out in the Devices menu and press . The Alarm-Out screen (Figure 3-41) allows you to change the settings and establish a schedule for each alarm output from the DVR. Figure 3-41 Alarm-Out Settings Screen 2. Each alarm output can be given its own title by highlighting the box under the Title heading and pressing . A virtual keyboard appears allowing you to enter the title. 3.
Configuration 7. a. The Day box allows you to select the days that the alarm schedule will be active. The choices are: Sun, Mon, Tue, Wed, Thu, Fri, Sat, M~F, Hol and All. b. The Range box allows you to set the time that the alarm schedule will be active in 15-minute increments from 00:00 to 24:00. c. The Mode box allows you to set how the alarm reacts during the scheduled time. When set to On, the Alarm-Out is active during the scheduled time.
Configuration 2. Highlighting an item and pressing toggles that item On and Off. When an item is On, there is a checkmark in the box beside it. The following items can be turned On or Off: • • • • • • • • • • • • • • Remote Control — The icon displays when the DVR can be controlled by the infrared remote control. Zoom — The icon displays on the enlarged video. Network — The icon displays when the unit is connected to a network via either Ethernet or modem.
Configuration Figure 3-45 6. Main Monitor Screen Here you can adjust the display dwell time for each camera displayed in sequence on the main monitor. Highlight the box beside Mode and press You can select between Full Sequence and Cameo Sequence. . Pressing SEQUENCE causes the DVR to sequence cameras, and the DVR can sequence cameras in two modes: Full and Cameo. In the Full mode, the DVR sequences through the cameras and displays them full screen.
Configuration Figure 3-46 Spot Monitor Screen 10. You can define which cameras display sequentially on the Spot Monitors. Highlight the box in the Channels column for the desired Spot Monitor and press . 11. You can save your Display settings by highlighting Save and pressing Selecting Cancel exits the screen without saving the changes. . Remote Control Screen 1. Highlight Remote Control in the Devices menu and press .
Configuration 4. Highlight the box beside Remote Control Product and select the device from the list. 5. You can save your Remote Control settings by highlighting Save and pressing . Selecting Cancel exits the screen without saving the changes. Recording Settings Your DVR offers a variety of flexible recording modes. You can set it up to record all the time or to only record events.
Configuration 2. Highlighting Recycle and pressing toggles between On and Off. In the Recycle mode, the DVR records over the oldest video data once all available storage space has been used. When Recycle is turned off, the DVR stops recording once all available storage space has been used. 3. Highlight the Resolution box and select from High and Standard. All other variables being equal; selecting High resolution will decrease the recording and playback speed by half that of Standard resolution. 4.
Configuration Figure 3-50 Schedule Setup Screen You can program the DVR to record only during certain times based on time of day, day of the week, and holidays. The smallest time segment you can use is 15 minutes. 2. Highlighting Schedule On and pressing toggles between On and Off. In the Schedule On mode, the DVR records video based on the schedule(s) established in the Schedule screen.
Configuration 7. Highlight the box under the Channels heading and press cameras will be recorded. 8. Highlight the box under the Settings heading and press to define the recording settings. You can set the ips and Quality of the recording for any modes you set up in the Mode column. If you do not set the ips and Quality in the Settings column, the DVR will follow the default settings. See Figure 3-51 for details. 9. Highlight the box under the heading and press to delete the recording settings.
Configuration When the DVR is in the Event Record mode it is possible to have it record images before the event occurs. The Pre-Event screen allows you to define how to handle pre-event recording. 2. You can turn individual cameras On or Off for pre-event recording. The image speed can be set from 0.10 to 30.00 ips (25.00 ips PAL), and image quality can be selectable from Very High, High, Standard and Low. 3. You can set the amount of time to record prior to the event by adjusting the Dwell.
Configuration 4. You can accept the Archive Data Range by leaving the default checkmarks in the Last Archived and Continue boxes. If you wish to enter specific times and dates in From and To, toggle the checkmarks Off and then enter the time and date. 5. Highlight Recycle and press to toggle between On and Off. When Recycle is On and the storage device is full, the newest archived video data will overwrite the oldest archived data.
Configuration Alarm-In Screen 1. Highlight Alarm-In in the Event menu and press (Figure 3-55) appears. Figure 3-55 Alarm-In Settings Screen 2. The alarm terminal strip on the back of the DVR has inputs associated with each alarm. You can set up each input on the Alarm-In screen. You can turn each input On or Off by highlighting the alarm number and pressing . 3. Each input can be given a title. Highlight the desired Title box and press virtual keyboard appears allowing you to enter a title name. 4.
Configuration You can set the actions the DVR will take whenever it senses an input on one of its alarm input connectors. 7. Highlight the desired box under the Record heading, and press . A list of cameras appears. Select the cameras that you want the DVR to record whenever it detects an input on the associated alarm input. Note 8. Highlight the desired box under the Alarm-Out heading, and press . A list of Alarm Outputs and Beep appear.
Configuration Figure 3-58 Alarm-In Actions 2 Screen 11. In the Actions 2 tab, highlight the desired box under the PTZ heading, and press . A list of PTZ presets appears. Select the preset position for each PTZ camera, where you want PTZ cameras to move to whenever the DVR detects an input on the associated alarm input. 12. Highlight the desired box under the Spot Monitor heading, and press . A list of SPOT monitors and cameras appears. Each SPOT monitor can be associated with a camera.
Configuration 3. Highlighting the box under the Sensitivity heading and pressing allows you to adjust the DVR’s sensitivity to motion for Daytime and Nighttime independently. There are five settings with 1 being the least sensitive and 5 being the most sensitive. Figure 3-60 4. Motion Detection Sensitivity Screen You can adjust the minimum number of detection blocks that must be activated to trigger a motion alarm. Highlighting the box under the Min.
Configuration Note 7. You can set up motion zones one block at a time in groups of 8 or 16 individual block groups (9- and 16-channel DVR respectively). A block group is positioned within the image area using the Up and Down arrow buttons, and individual blocks within the block groups are selected or cleared using the camera buttons. Press to display the menu screen. The menu on the setup screen has the following functions: Figure 3-63 • • • • • • • • 8.
Configuration 10. Highlight the box beside Daytime and press . Use the Up and Down arrow buttons to set the Daytime range. The DVR will consider the remaining time range as the Nighttime. 11. Highlight the Actions 1 and Actions 2 tabs and the Motion Detection Actions 1 (Figure 3-65) and Actions 2 (Figure 3-66) screens display. Figure 3-65 Motion Detection Actions 1 Screen The DVR can be set to react to motion detection differently for each camera.
Configuration Note For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the Alarm-Out setup screen, Schedule tab (see Alarm-Out Screen, page 65). 14. Highlight the box under the Notify heading and press . You can toggle the entire list On and Off by highlighting Notification and pressing . You can toggle the individual items On and Off by highlighting that item and pressing Highlight OK and press to accept your changes. Note .
Configuration Video Loss Screen 1. Highlight Video Loss in the Event menu and press screen (Figure 3-67) appears. Figure 3-67 . The Video Loss setup Video Loss Settings Screen 2. The DVR checks to see if anything is obscuring the camera. Highlight the slider bar beside Check Obscuration, and use the Left and Right arrow buttons to adjust the setting. The sensitivity can be set from Never to 255 (extremely sensitive). 3.
Configuration Note 5. Highlight the box under the Alarm-Out heading and press . A list of Alarm Outputs appears. You can associate as many Alarm-Outs with that camera as you wish. When the DVR detects video loss on the selected camera, it will trigger output signals on all the associated Alarm-Out connectors. You can also have the DVR’s internal buzzer sound if video is lost on the selected camera. Note 6.
Configuration 8. Highlight the box under the Spot Monitor heading and press . A list of SPOT monitors and cameras appears. Each SPOT monitor can be associated with a camera. The DVR will display the associated camera on the SPOT monitor whenever it detects video loss on the selected camera. 9. You can save your Video Loss changes by highlighting Save and pressing Selecting Cancel exits the screen without saving the changes. . Text-In Screen 1.
Configuration 3. 86 Figure 3-71 Text-In Device (VP Filter) Settings Screen Figure 3-72 Text-In Device (Generic Text and EPSON-POS) Settings Screen Highlight the box beside Port, and press and USB-Serial (1~8). . Select from None, RS232, RS485 Note If you have set the Port as None, you will not be able to make any changes to the screen. Note When using the USB to serial text-in device, do NOT remove the USB cable from the port while the system is running. 4. Highlight Setup…, and press .
Configuration Note The screen changes for the different types of text input devices, changing the parameter boxes for you to enter information. 6. Highlight the box beside Virtual Port, and press . Select the port number to use. This field will be activated only when setting up the VP Filter device. 7. Highlight the box beside Transaction Start, and press . Use the virtual keyboard to enter the Transaction Start string.
Configuration Figure 3-73 Text-In Actions 1 Screen The DVR can be set to react to text input. Text input can be associated with cameras, trigger an Alarm-Out connector, sound the DVR’s internal buzzer, notify a number of different devices, move PTZ cameras to preset positions, and/or display a camera on a SPOT monitor. 16. Highlight the box under the Record heading and press . A list of cameras appears. You can associate as many cameras with the Text Input as you wish.
Configuration Note For the Notify action, the notify item you select should be enabled in the Notification setup screen and the DVR should be registered in the RAS (Remote Administration System). Figure 3-74 Text-In Actions 2 Screen 19. Highlight the desired box under the PTZ heading, and press . A list of PTZ presets appears. Select the preset positions for each PTZ camera, this is where you want PTZ cameras to move to when the DVR detects text input. 20.
Configuration Figure 3-75 Health Check Screen The DVR can be configured to run self-diagnostics and report the results. 2. Highlighting the box beside System and pressing allows you to select the interval that you want the DVR to run self-diagnostics on the system. You can select from 1 hr to 30 days, or Never. 3. Highlight the Setup... box beside Check Recording and press . The Check Recording screen appears. Highlighting Schedule On and pressing toggles the schedules On and Off.
Configuration Figure 3-77 Storage Screen 6. Highlight the box beside Disk Bad Notify, and press . Select the percentage level of bad disk sectors at which point you want the DVR to trigger an alert. Percentage levels range from 10% to 90%. 7. Highlight the box beside Disk Almost Full Notify, and press . Select the percentage level of disk usage at which point you want the DVR to trigger an alert. Percentage levels range from 80% to 99%. 8. Highlight the Setup… box beside Disk S.M.A.R.T.
Configuration 12. Highlight the second box beside Temperature Threshold, and press either °C (Celsius) or °F (Fahrenheit), and press . Note . Select The box beside Last Check-Time displays the Date and Time of the last S.M.A.R.T. check. 13. Highlight OK, and press to accept the changes. Selecting Cancel exits the screen without saving the changes. 14. Highlight the Actions tab and the System Event Actions screen (Figure 3-79) displays.
Configuration Note Mail notify is the only option available for the System event. Note For the Notify action to work, the DVR should be registered in the RAS (Remote Administration System). 17. You can save your System Event changes by highlighting Save and pressing Selecting Cancel exits the screen without saving the changes. . Event Status Screen Highlight Event Status in the Event menu and press (Figure 3-80) appears. Figure 3-80 .
Configuration • Disk Almost Full will be highlighted when the DVR is not in the Recycle mode and the level of disk usage reaches the Disk Almost Full percentage you specified in the System Event setup screen on the Event menu. Disk Full will be highlighted when the DVR is not in the Recycle mode and all available storage space has been used. Highlighting the Storage tab will display the hard disk drive status. Refer to Storage Screen, page 45 for more details.
Operation 4 Operation Note This chapter assumes your DVR has been installed and configured. If it has not, please refer to Chapter 2 and Chapter 3. The DVR’s controls are similar to a VCR. As with a VCR, the main functions are recording and playing back video. However, you have much greater control over recording and playing back video. You can establish recording schedules based on time of day and day of the week.
Operation Live Monitoring As soon as the DVR completes its initialization process, it will begin showing live video on the attached monitor and playing live audio through the attached speaker. The default mode is to display all cameras at once. Pressing any camera button will cause that camera to display full screen. It displays live video and plays live audio until the user enters another mode. Pressing DISPLAY cycles the DVR through the different display formats.
Operation Active Cameo Mode You can enter the Active Cameo mode by pressing in any multi-view format. The yellow outline surrounding the video indicates the active cameo, and pressing the arrow buttons moves the active cameo. Pressing while in the Active Cameo mode exits the Active Cameo mode. The active cameo mode will remain in effect for 15 seconds if there is no further operation. In active cameo mode, press the button for the camera you want displayed as active cameo.
Operation Figure 4-1 2. Use the front panel buttons to control the PTZ. Press the Left and Right arrow buttons to pan left and right. Press the Up and Down arrow buttons to tilt the camera up and down. Press to zoom in, and press to zoom out. You can use and to focus the image. 3. You can establish preset positions for PTZ cameras. Press Presets. Figure 4-2 4. 98 PTZ Select Camera Menu to establish PTZ Set Preset Screen You can quickly move PTZ cameras to Preset positions.
Operation Figure 4-3 5. 6. You can save camera position settings as presets so that you can go directly to desired views. a. Once you have the camera at the desired settings, press Preset dialog box will appear. b. Select the number you want to assign to the preset and press c. Use the virtual keyboard to enter the preset name. d. Press , and the PTZ e. Select the desired preset and press . to load the PTZ preset and the Preset View dialog box will appear. to load the preset.
Operation 8. Clicking on the left side closes the toolbar. If you want to display the toolbar again, position the mouse pointer at the bottom of the screen. Change the toolbar location by clicking the empty space on the left side of the toolbar and drag it to where you want it located on the screen. Use the arrow buttons on the toolbar to pan or tilt the camera in the direction you want.
Operation How the cameras are displayed depends on the number of cameras associated with the event. If one camera is associated with the event, the DVR will display the camera full screen. If two to four cameras are associated with the event, the DVR will display the cameras on a 2x2 screen. If five to nine cameras are associated with the event, the DVR will display the cameras on a 3x3 screen. If 10 or more cameras are associated with the event, the DVR will display the cameras on a 4x4 screen.
Operation 1. Press SPOT on the front panel or remote control, then select one of four Spot Monitors. 2. Select the camera to be displayed on the Spot Monitor. Figure 4-6 Spot Monitor Menu If you want to display more than one camera on a Spot Monitor, you can display them sequentially: 1. In the Spot Monitor selection mode, press SEQUENCE on the front panel or remote control, or select Sequence On from the menu to start displaying cameras sequentially. 2.
Operation Using a Mouse You can use a mouse instead of the front panel buttons to perform many of the DVR functions. The following operations are supported when using a mouse during live monitoring: • • • When in one of the multi-view formats (for example, PIP, 2x2, 3x3 or 4x4), clicking the mouse button on a camera image switches that camera to full screen. Clicking the mouse button again returns to the previous multi-view format.
Operation Figure 4-9 • • • • Mouse Display Menu Clicking Camera and selecting the camera number is the same as pressing the individual camera buttons on the front panel which displays the selected camera full screen. When in the PIP display mode, clicking the right mouse button and selecting PIP changes the location and the size of the PIP. Selecting PIP, 2x2, 3x3 and 4x4 displays the cameras in the selected multi-view screen mode.
Operation Pressing PANIC starts panic recording of all cameras, and pressing the button again stops panic recording. If you set the Panic Recording Duration in the Record Screen (see Record Screen, page 70), panic recording will stop automatically according to the preset duration as long as PANIC is not pressed. Note When the DVR is not in Recycle mode and all available storage space has been used, panic recording will not operate.
Operation Note While playing back video, the recording speed might decrease. Note Only the administrator and users with Covert Camera View authority can view video from covert cameras. The covert cameras in the playback mode are determined by the current camera settings. Pressing PLAY/PAUSE again will freeze the video on the screen. RW (Rewind) Button Pressing RW plays video backward at high speed. Pressing the button again toggles the playback speed between , and .
Operation SEARCH Button Pressing SEARCH while in the Playback mode returns the DVR to the Live Monitoring mode. Pressing SEARCH while in the Live Monitoring mode returns the DVR to the Search mode. Camera Buttons (1 to 16) Pressing a camera button will display that camera full screen. DISPLAY Button Pressing DISPLAY will cycle the display through the different screen layouts. The display modes are: 4x4, PIP, 3x3 and 2x2 (not all formats are available for the 9-channel DVR).
Operation You can also use a mouse for convenient playback control. Position the mouse pointer on the search screen, and the following search toolbar will display. Figure 4-10 Mouse Playback Controls Clicking on the left side exits the toolbar. If you want to display the toolbar again, position the mouse pointer on the screen. Change the toolbar location by clicking the empty space on the right side of the toolbar and drag it to where you want it located on the screen.
Operation Figure 4-11 • • • • • • • • • • • • • Search Menu Go to the First — Displays the first recorded image Go to the Last — Displays the last recorded image Go to the Date/Time… — Searches by date and time (see below for more details) Calendar Search… — Searches using a calendar (see below for more details) Event Log Search… — Selects video from the event log (see below for more details) Text-In Search… — Searches text input strings (see below for more details) Motion Search… — Searches motion event
Operation 2. You can use the Left and Right arrow buttons to highlight the year, month, day, hours, minutes and seconds. Use the Up and Down arrow buttons to change to the date and time you want to search for video. 3. Once you have set the date and time you want, press press . 4. Video from the selected date and time will display (if no video was recorded during the selected time, a message appears alerting you that no image was recorded at that time).
Operation 4. If the DVR’s time and date have been reset to a time that is earlier than some recorded video, it is possible for the DVR to have more than one video stream in the same time range. Move to Select a Segment, and select the video stream you want to search. Refer to Appendix E, Time Overlap for further information on searching time-overlapped video streams. Note 5. The lower number of the Segment indicates the latest recorded video.
Operation 1. Use the arrow buttons to highlight the event for which you would like to see video. 2. Pressing 3. Pressing PLAY/PAUSE will start playing the event video segment. Pressing SEARCH returns to live monitoring. Note 4. will extract the event video and display the first image of the event. It is possible that no recorded image displays on the current screen. Press DISPLAY and change the screen mode to 4x4.
Operation f. Highlight the box beside Video Loss and press . You can select the cameras for which you want to search for any reports of lost video. g. Highlight the box beside Text-In and press . You can select the text-in devices for which you want to search for any report of text input. h. Highlight the box beside Record Channels and press . You can select the cameras that you want to search for any reports of event recorded data.
Operation 3. 4. Pressing PLAY/PAUSE will start playing the event video segment. Pressing SEARCH returns to live monitoring. Note It is possible that no recorded image displays on the current screen. Press DISPLAY and change the screen mode to 4x4. You will be able to easily see which camera(s) have recorded video during the target time. Note Text Input information will be overlaid on the image while the recorded video is played at regular speed.
Operation 5. e. Highlighting + and pressing allows you to add a new search parameter. Set up the desired search parameter. Refer to Appendix B, Text In Search Examples for more information on setting up search parameters. The column can be used to delete a single search parameter or all of the search parameters. f. Highlight Case Sensitive and press . This will toggle between On and Off. When this feature is On, the search will find only those text strings in which the case matches. g.
Operation Figure 4-19 Motion Search Option Screen You can search video from the first to last recorded images, or you can set the start and stop times and dates. 116 a. Highlight the box beside From and press to toggle between On and Off. When set to Off, you can enter a specific Date and Time. When set to On, the search will be from the first recorded image. b. Highlight the box beside To and press to toggle between On and Off. When set to Off, you can enter a specific Date and Time.
Operation 6. Once you set your desired search conditions, highlight Search and press to display the search results in the Motion Search screen. Selecting Cancel exits the screen without saving the changes. When you search for motion events of another camera, you will be asked whether or not you want to delete the previous search results from the list. Clip-Copy Screen The Clip-Copy screen can be used to copy video clips to an internal CD-RW or DVD-RW drive, or external USB hard disk, CD-RW or flash drive.
Operation 6. You can search video from the first to last recorded images, or you can set the start and stop times and dates: • • Highlight the box beside From and press to toggle between On and Off. When set to Off, you can enter a specific Date and Time. When set to On, the search will be from the first recorded image. Highlight the box beside To and press to toggle between On and Off. When set to Off, you can enter a specific Date and Time.
Operation Note When naming a file, you cannot use the following characters: \, /, :, *, ?, ", <, >, |. 11. Highlight Include Text-In Data and press . This will toggle between On and Off. When this feature is On, you can include text-in data when copying video if the recorded video has text-in data. 12. Highlight Verify After Burning and press . This will toggle between On and Off. When this feature is on, you can verify that the data is written on the CD-RW or DVD-RW properly. 13.
Operation Caution Do NOT disconnect the USB cable or the power from the external drive while copying video clips. If the external drive is shut down or the USB cable is disconnected while copying video clips, THE DVR SYSTEM MAY NOT WORK NORMALLY OR THE EXTERNAL DRIVE COULD BE DAMAGED, and you will get an error message the next time you try to copy video clips. You will need to power down the DVR and restart it to get rid of the error message.
USB Hard Disk Drive Preparation A USB Hard Disk Drive Preparation Preparing the USB-IDE Hard Disk Drive in Windows 2000 Note Preparing a USB-IDE hard disk drive under Windows XP is almost identical to Windows 2000. 1. Connect the USB-IDE hard disk drive to your computer using the USB Cable. 2. Turn on your computer. 3. The USB device icon should display on the Taskbar. 4. If the USB-IDE hard disk drive is partitioned or has data, it will show up in My Computer as a hard disk drive icon.
USB Hard Disk Drive Preparation After formatting is complete, the USB-IDE hard disk drive will be added to My Computer. 7. Connect the USB-IDE hard disk drive to the DVR. Preparing the USB-IDE Hard Disk Drive in Windows 98 Note Preparing a USB-IDE hard disk drive under Windows ME is almost identical to Windows 98. 1. Connect the USB-IDE hard disk drive to your computer using the USB Cable. 2. Turn on your computer. The Add New Hardware wizard window will appear. 3.
Text In Search Examples B Text In Search Examples Search Example 1 1 2 3 4 5 6 123456789012345678901234567890123456789012345678901234567890 Item Unit price Qty amount ================================================== ❘ $ 2.20 ❘ 1(s) ❘ $ 2.20 Coke Fanta ❘ $ 2.20 ❘ 1(s) ❘ $ 2.20 ❘ $ 3.50 ❘ 3(s) ❘ $ 10.50 Hotdog ❘ $ 1.95 ❘ 1(s) ❘ $ 1.95 Pepsi ================================================== total : $ 16.
Text In Search Examples Figure B-1 Text-In Search Option Example 1 Search Example 2 1 2 3 4 5 6 123456789012345678901234567890123456789012345678901234567890 Item Unit price Qty amount ================================================== ❘ $ 2.20 ❘ 1(s) Coke $ 2.20 ❘ $ 2.20 ❘ 1(s) Fanta $ 2.20 ❘ $ 3.50 ❘ 3(s) Hotdog $ 10.50 ❘ $ 1.95 ❘ 1(s) Pepsi $ 1.95 ================================================== total : $ 16.
Text In Search Examples Figure B-2 Document 900.
Text In Search Examples 126
Reviewing Video Clips C Reviewing Video Clips You do not need to install any special software on your personal computer to review the video clips. The copied video clip contains the Clip Player program. 1. If you used a USB device, disconnect either the external USB-IDE hard disk drive or USB flash drive from the DVR, and connect it to your PC. If you used a recordable CD, insert the CD in your computer’s CD drive. 2. Double-clicking the target clip file starts the Clip Player program.
Reviewing Video Clips 3. The Clip Player Screen displays the clip images. Use the player controls to review the clip. Note • • • • • • • • • • • • 128 Proper image display depends on the display settings of your PC. If you are experiencing display problems, click the right mouse button on the background screen and select Properties > Settings then set the Color quality to 32 bit. Then select Advanced > Troubleshoot and set Hardware Acceleration to Full. Please make sure that DirectX version 8.
Reviewing Video Clips • • • Note Image Processing works only in the single-screen layout and in pause mode. Note If you are not sure about the appropriate Video Format option, try each option until the image displays properly. Click to select from Normal and Double screen views. Clicking the left mouse button on the enlarged image moves its position. Click to display the image full screen. Encryption icons display in the bottom-right corner.
Reviewing Video Clips 130
WebGuard D WebGuard WebGuard allows you to access a remote DVR, monitor live video images and search recorded video using Internet Explorer web browser anytime from virtually anywhere. Computer system requirements for using the WebGuard program are: • • • • • 1. Operating System: Microsoft® Windows® 2000, Microsoft Windows XP or Microsoft Windows Vista CPU: Intel Pentium III (Celeron) 600MHz or faster RAM: 128MB or higher VGA: 8MB or higher (1024 x 768, 24bpp or higher) Internet Explorer: Version 6.
WebGuard Note When running WebGuard in the Microsoft Windows Vista operating system, it is recommended to start Internet Explorer with elevated administrator permissions. Click the right mouse button on the Internet Explorer icon and select the Run as administrator option from the context menu. Otherwise, some functions of WebGuard might be limited to use. Figure D-1 132 WebGuard Login Screen 2.
WebGuard Web Monitoring Mode WebWatch is a remote web monitoring program that allows you to monitor live video transmitted in real-time from the remote DVR. Figure D-2 WebGuard Screen 1. Click to log out of the WebGuard program. 2. Click to access the web search mode. 3. Position the mouse pointer on the WebWatch logo to see the version of the WebGuard program. 4. The DVR information window displays the login information of WebGuard. 5.
WebGuard 7. Click image. to adjust the brightness, contrast, saturation and hue of the monitoring 8. Click to control pan, tilt, and zoom of a PTZ camera from a remote site. 9. Click to control alarm out devices at the remote site. 10. Click to save the current image as a bitmap or JPEG file format. 11. Click to set up the image drawing mode and OSD display. You can adjust the display speed by changing the image drawing mode, and select the OSD information to display on the screen. 12.
WebGuard Web Search Mode WebSearch is a remote web search program that allows you to search recorded video on the remote DVR. Note The remote site connection in the Web Search mode will automatically be disconnected if there is no activity for 30 minutes. Figure D-3 WebSearch Screen 1. Click to log out of the WebGuard program. 2. Click to access to the web monitoring mode. 3. Position the mouse pointer on the WebSearch logo to see the version of the WebGuard program. 4.
WebGuard 5. Click to blur, sharpen, equalize and interpolate playback images. Click to zoom out or zoom in on the recorded image. Click to adjust the brightness of the recorded images. Note Image processing works only in the pause mode. 6. The playback function buttons include fast backward, pause, play, fast forward, go to the first image, go to the previous image, go to the next image, and go to the last image. 7. Click the screen format to select the desired display mode. 8.
WebGuard 14. Selecting a camera on the screen and clicking the right mouse button dispays the text menu screen. • • • Change Camera Title: Changes the camera name. Aspect Ratio: Changes the image aspect ratio. Anti-Aliasing Screen: Enhances image display quality by eliminating stair stepping (aliasing) effects in the enlarged image. Note Document 900.0856 Rev B 02/08 The camera name changed in the Web Search mode does not affect the camera name set up on the remote site.
WebGuard 138
Time Overlap E Time Overlap If the DVR’s time and date have been reset to a time that is earlier than the existing recorded video, it is possible for the DVR to have more than one video stream in the same time range. In this case, you can search overlapping video streams individually by selecting a specific segment.
Time Overlap 140
Troubleshooting F Troubleshooting Table F-1 Troubleshooting Problem Possible Solution No Power • • Check power cord connections. Confirm that there is power at the outlet. No Live Video • • • • Check camera video cable and connections. Check monitor video cable and connections. Confirm that the camera has power. Check camera lens settings. Live Video very bright If a cable is attached to the Loop connector, make certain it is connected to a properly terminated device.
Troubleshooting 142
Connector Pin Outs G Connector Pin Outs I/O Connector Pin Outs Document 900.
Connector Pin Outs RS485 Connector Pin Outs Master Unit Slave Unit + ! To ! TX+ – ! To ! TX– + ! To ! RX+ – ! To ! RX– 144
Map of Screens H Map of Screens Document 900.
Map of Screens 146
System Log Notices I System Log Notices Boot Up Schedule On Shutdown Schedule Off Restart Panic On Upgrade Panic Off Upgrade Fail Clear All Data Power Failure Clear Disk Time Change Format Disk Time Zone Change Disk Full Time Sync Auto Deletion Time Sync Fail Search Begin Disk Bad Search End Login Clip-Copy Begin Logout Clip-Copy End Setup Begin Clip-Copy Cancel Setup End Clip-Copy Fail Remote Setup Change Callback Fail Remote Setup Fail Print Begin Setup Imported Print E
System Log Notices 148
Error Code Notices J Error Code Notices System Upgrade Related Number Description 0 Unknown error 1 File version error 2 Operating system version error 3 Software version error 4 Kernel version error 100 Upgrade device mounting failed 101 Package is not found 102 Extracting package failed 103 LILO failed 104 Rebooting failed 105 Invalid package 106 ODD firmware upgrade failed 300 Remote connection failed 301 Remote network error 302 Remote upgrade is not authorized 303 Savi
Error Code Notices Clip Copy Related 150 Number Description 0 Unknown error 1 Device error 2 Mounting failed 3 No media 4 Invalid media 5 File already existed 6 Not enough space 7 Creating temporary file failed 8 Opening disk failed 9 Formatting disk failed 10 Database has been changed 11 Appending failed 12 Bad sector 13 No executable file 14 Opening executable file failed 15 Writing executable file failed 16 Creating image failed 17 Burning failed 18 Burning is ou
Specifications K Specifications Note Specifications are subject to change without notice. Video Signal Format NTSC or PAL (Auto Detect) Video Input Composite: 9 or 16 looping inputs, 1 Vp-p, auto-terminating, 75 Ohms Monitor Outputs Composite: 1 BNC, 1 Vp-p, 75 Ohms SVHS: 1 SPOT: 4 BNC, 1 Vp-p, 75 Ohms VGA: 1 • NTSC: 30.8 kHz (horizontal frequency) / 60 Hz (vertical frequency) • PAL: 30.
Specifications Inputs / Outputs Audio Input RCA Input: 4 Line In Audio Output RCA Output: 1, Line Out IR Port 1 Remote Control Connectors Video Input Composite: 9 or 16 BNC Video Loop Composite: 9 or 16 BNC (Auto Terminating) Monitor Output Composite: 1 BNC SVHS: 1 Y/C* VGA: 1 VGA SPOT (Composite): 4 BNC Audio In 4 RCA connector Audio Out 1 RCA connector Alarm Input/Output 16/16 Push-button, Terminal Blocks Ethernet Port RJ-45 RS232C Serial Port DB9 (P) RS485 Serial Port Two-connector
Specifications General Dimensions (W x H x D) 16.9” x 3.5” x 15.9” (430 mm x 88 mm x 405 mm) Unit Weight 16.3 lbs. (7.4 kg) Shipping Weight 23.6 lbs. (10.7 kg) Shipping Dimensions (W x H x D) 21.3” x 11.4” x 23.2” (540 mm x 290 mm x 590 mm) Operating Temperature 41°F to 104°F (5°C to 40°C) Operating Humidity 0% to 90% Power 100 to 240 VAC, 2 A, 60/50 Hz Power Consumption Max. 85 W (100 W when 4 hard disk drives are installed) Approvals FCC, UL, CB, CE Note Document 900.
Specifications 154
www.honeywellvideo.com +1.800.796.CCTV (North America only) HVSsupport@honeywell.com Document 900.0856 – Rev B – 02/08 © 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.