Addressable Fire Alarm Control Panel MS-9600LS/MS-9600LSE MS-9600UDLS/MS-9600UDLSE MS-9600LSC Manual Document 52646 2/12/2010 Rev: P/N 52646:B2 B2 ECN 10-098
Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system—typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control panel with remote notification capability—can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire.
Installation Precautions Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood.
Software Downloads In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product prior to commissioning any system.
Table of Contents Section 1: Product Description ............................................................................................. 13 1.1: Inventory......................................................................................................................................................13 1.2: Features and Options ...................................................................................................................................13 1.3: Specifications....................
Table of Contents Section 3: Programming ........................................................................................................ 61 3.1: Programming Data Entry .............................................................................................................................61 3.2: User Programming .......................................................................................................................................62 3.3: Initial Power-up.........................
Table of Contents Section 4: Operating Instructions ....................................................................................... 150 4.1: Panel Control Buttons................................................................................................................................150 4.1.1: Acknowledge/Step...........................................................................................................................150 4.1.2: Alarm Silence ......................................
Table of Contents 5.4.2: Selecting and Locating Batteries .....................................................................................................177 Appendix A: Software Zones............................................................................................... 178 A.1: Correlations ...............................................................................................................................................178 Appendix B: Default Programming .......................
It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies: • Underwriters Laboratories Standards • NFPA 72 National Fire Alarm Code • CAN/ULC - S527-99 Standard for Control Units for Fire Alarm Systems Before proceeding, the installer should be familiar with the following documents.
MS-9600LS Series Manual — P/N 52646:B2 2/12/2010 Notification Appliance Circuits 9600udleslayout.wmf Important: Removing Ground Fault Disable jumper JP2 voids UL/NFPA Style/Class identification for circuits. Remove jumper JP2 only with AHJ (Authority Having Jurisdiction) approval Resettable Power - 24 VDC filtered, power-limited, (1.5 amps maximum) to smoke detectors. Supervision required.
Peripheral Devices and Their Documents: Audio Control for ACC-25/50(ZS/T) Audio-Command-Center Doc. #51889 ANN-80 Text Annunciator Doc. #52749 ANN-RLY Form-C Relay Card Doc. #53033 ANN-I/O LED Driver Doc. #151416 ANN-(R)LED LED Display Doc. #53032 ANN-S/PG Printer Driver Doc. #151417 IPDACT Internet Communicator Doc. # 53109 ANN (EIA-485) TB6 J2 Connector DACT-UD2 Communicator Doc. # 53037 4XTMF Reverse Polarity module SLC Loop Addressable Devices and SLC Wiring Doc. # 51309 9600LSperi.
Notes 12 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010
Section 1: Product Description The MS-9600LS and MS-9600UDLS are compact, cost effective, intelligent addressable FACPs (Fire Alarm Control Panels) with an extensive list of powerful features. The combination of Fire•Lite’s newer series devices and legacy 300 Series devices, along with the MS-9600LS or MS9600UDLS FACP, offer the latest in fire protection technology. The FLPS-7 power supply is a separate board while all other electronics are contained on a single main circuit board.
Product Description Features and Options • Optional module for adding a second SLC loop which meets NFPA Style 4, 6 and 7 requirements • 318 addressable device capacity for each SLC loop (159 detectors and 159 control/monitor modules) • 99 software zones • Up to four onboard NACs (Notification Appliance Circuits): four Style Y (Class B) or two Style Z (Class A) • Additional NAC capability using control modules • 7.
Specifications Product Description • Auto-program (learn mode) reduces installation time.
Product Description Specifications Maximum signaling current per circuit: 3.00 amps (see Figure 1.1 on page 17) End-of-Line Resistor: 4.7 k, ½ watt (P/N 71252 UL listed) for NACs Refer to Device Compatibility Document for listed compatible devices Two Programmable and One Fixed Output Relay - TB1 & TB5 Contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive) Form-C relays Refer to Figure 2.
Controls and Indicators Product Description 1.3.1 Current Availability The following figure illustrates the maximum current that is possible for each panel circuit and the total current available from the FACP power supply. TB3 1 Resettable Special Application Power Power #1 3 Resettable Special Application Power Power #2 5 2 4 6 NAC 1 Style Y or Z 1 NAC 3 Style Y only 3 NAC 2 Style Y or Z 5 NAC 4 Style Y only 7 2 4 6 8 1.5 amps max per circuit 1.5 amps max per circuit Standby 1.
Product Description Circuits • Maintenance/presignal (yellow) • Alarm Silenced signals (yellow) • Disabled (yellow) • Battery fault (yellow) • Ground fault (yellow) Key Panel Mounted on the main circuit board, the key panel includes a window for the LCD display and LED indicators as listed above. The key panel, which is visible with the cabinet door closed, has 25 keys, including a 16 key alpha-numeric pad similar to a telephone keypad.
Components Product Description NAC (Notification Appliance Circuits) Up to four NACs are provided with various programmable features: • four Style Y (Class B) NACs OR • two Style Z (Class A) NACs Relays One fixed and two fully programmable Form-C dry contact relays are provided. The fixed fail-safe relay monitors system trouble and the two programmable relays are factory default programmed for system alarm and system supervisory. Contacts are rated 2.0 amps @ 30 VDC (resistive) and 0.
Product Description Components the BB-26 can be used for housing the batteries. The CHG-120F can be used for charging 26 to 120 AH batteries and the BB-55F can be used for housing the batteries. Batteries must be ordered separately. 1.6.1 Intelligent Addressable Detectors: Newer Series Intelligent, addressable detectors provide information to the control panel on an SLC Signaling Line Circuit (refer to the SLC Wiring Manual for detailed information on device installation, wiring and operation).
Optional Modules Product Description N-ELR Mounting Plate The N-ELR is a single End-of-Line resistor plate which is required for use in Canada. An ELR, which is supplied with each module and fire alarm control panel, is mounted to the ELR plate. Resistors mounted to the N-ELR plate can be used for the supervision of a monitor and control module circuit. 1.
Product Description Accessories Important: Remote modification of FACP programming requires that the panel be enabled for remote download (refer to the DACT-UD2 manual). Remote interrogation of panel programming, history logs, detector status, etc., is possible without enabling the remote download option. 1.8.2 Dress Panel: DP-9692 A DP-9692 dress panel is available for the FACP (required for Canadian installations).
Accessories Product Description 1.8.6 New ANN-BUS Annunciators/Devices NOTE: Refer to “Canadian Application” on page 200 for specific Canadian requirements. ! WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The legacy ACS annunciators may not be used if new ANN-BUS annunciators are being used due to incompatible serial communication protocols.
Product Description Accessories capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. The formula used to generate this chart is shown in the note below. Wiring Distance: ANN-BUS Modules to FACP Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100 1,852 ft. 4,688 ft. * 6,000 ft. *6,000 ft. 0.200 926 ft. 2,344 ft. 3,731 ft. 5,906 ft. 0.
Accessories Product Description The total worst case current is calculated as follows: ANN-80 Current Draw = 3 X 0.040 amps = 0.120 amps ANN-S/PG Current Draw = 1 X.0.040 amps = 0.040 amps ANN-I/O Current Draw = 1 X.0.200 amps = 0.200 amps Total Worst Case Current Draw = 0.360 amp Using this value and referring to the Wiring Distance Table 1.
Product Description Accessories Powering ANN-BUS Devices from Auxiliary Power Supply Figure 1.4 illustrates the powering of ANN-BUS devices from an auxiliary power supply such as the FCPS-24FS6/8, when the total ANN-BUS power requirement exceeds the capability of the FACP’s DC Power Output circuit. Cut Ground Fault Detection jumper JP1 (FACP monitors for ground faults) -24 VDC ANN-80 9600lstofcpstoann.
Accessories Product Description Address Switch 51 Switch 4 Switch 3 Switch 2 Switch 1 not valid OFF OFF OFF OFF OFF 01 OFF OFF OFF OFF ON 02 OFF OFF OFF ON OFF 03 OFF OFF OFF ON ON 04 OFF OFF ON OFF OFF 05 OFF OFF ON OFF ON OFF 06 OFF OFF ON ON 07 OFF OFF ON ON ON 08 OFF ON OFF OFF OFF 1 Switch 5 must be set to OFF for ANN-BUS devices to be recognized.
Product Description Accessories Annunciator backplate ann80_iso.wmf Annunciator cover with LCD display Press in latch and Pull annunciator cover open Key switch shown in OFF/Locked position Figure 1.5 ANN-80 Mounting TheANN-80 can be surface or semi-flush mounted to a single, double or 4” square electrical box. Select and remove the appropriate knockout(s), pull the necessary wires through the knockouts and mount the annunciator in or on the wall depending on the type of installation desired.
Accessories Product Description Wiring ANN-80 to FACP The following steps can be used as a guide to wire the annunciator. Make certain all power has been removed from the FACP prior to annunciator installation. Route wires from hole in backplate, through wiring channel and then to ANN-80 terminal block TB1. ann-80boxinside.wmf 1. wiring channel wires TB1 2. Remove appropriate amount of wire insulation. 3. Connect the wiring from the FACP ANN-BUS to annunciator TB1 terminals 3 (A) & 4 (B).
Product Description Accessories The following table shows the ANN-80 connections to the FACP FACP ANN-80 (TB1) Terminal GND (-) on TB3 Terminal 1 (-) Terminal PWR (+)TB3 Terminal 2 (+) Terminal ACS on TB6 Terminal 3 (A) Terminal ACS on TB6 Terminal 4 (B) Programming Following installation and wiring of the ANN-80 LCD annunciator to the FACP, the annunciator must added to the system via FACP programming.
Accessories Product Description 4. Select the address and configuration options for the ANN-S/PG module as described in the Programming section of this manual (refer to “ANN-BUS Options” on page 121). Note that the Auto-configure feature allows the programmer to quickly bring all installed ANN-BUS modules online (refer to “Auto-Configure” on page 131). 5. Connect a printer to the ANN-S/PG Parallel or Serial connectors (refer to Figure 1.7). Only one printer can be connected.
Product Description Accessories Standard Exec 10.5 SI.Zero On Auto LF On PAPER BIN 1 12/72” BIN 2 12/72” SINGLE 12/72” PUSH TRA 12/72” PULL TRA 12/72” PAP ROLL 12/72” Table 1.2 PRN-6F Setup Options ANN-I/O LED Driver Module* The ANN-I/O is an LED driver module that can be used in a wide variety of applications, including as an interface with most customized graphic annunciators.
Accessories Product Description Specifications • Max. ANN-BUS Voltage: 28 VDC • Max. Current: • Alarm: 200 mA • Standby: 35 mA • Each LED: 10 mA • Operating Temperature: 32oF to 120oF (0oC to 49oC) • For indoor use in a dry location only ANN-I/O Connection to FACP The ANN-I/O connects to the FACP via the ANN-BUS as illustrated in Figure 1.9. After the ANN-I/O is connected to the panel, it must be added to the system via FACP programming.
Accessories ann-ioleds.wmf Product Description Figure 1.10 ANN-I/O Board Layout ANN-LED Annunciator Module* The ANN-LED and ANN-RLED annunciator modules provide LED annunciation of general system faults and input zones/points when used with a compatible FACP. The ANN-LED module provides alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten input zones or addressable points. The ANN-LEDR provides alarm (red) indication for up to 30 input zones or addressable points.
Accessories Product Description ann-ledistacked.wmf *In Canada, the color red must be used to indicate active alarm inputs. Yellow indicates supervisory, burglary or trouble signals. Green indicates the presence of power or an activated output. Figure 1.11 ANN-LEDs (shown in possible stacked configuration) Specifications • Max. ANN-BUS Voltage: 24 VDC • Max.
Product Description Accessories ANN-LED Board Layout and Connection to FACP Figure 1.13 illustrates the ANN-LED board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. JP2 ANN-BUS (ID#) Address DIP switch 1 2 3 4 5 6 7 8 SW1 J1 ANN-BUS TB1 ANN-BUS and power wiring are supervised and power-limited ANN-LED TB3 -24 VDC +-+-+TB4 TB1 +- TB5 TB6 A B JP8 JP5 FACP 9600lstoled.wmf +24 VDC ANN-BUS/ ACS BUS Figure 1.
Accessories Product Description Mounting/Installation FACP Chassis Installation mounting holes ann-rlyinchassis.wmf The ANN-RLY relay module can be mounted inside the FACP main circuit board chassis or inside the ROME Series enclosure. Refer to the ANN-RLY Installation Document #53033 for instructions on chassis mounting or to the ROME Series Installation Document #53530 for mounting in the separate backbox.
Product Description Accessories ANN-RLY Board Layout and Connection to FACP Figure 1.15 illustrates the ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch Ground Wire attaches to chassis (see documentation supplied with module) ANN-BUS -24 VDC FACP 9600lstorly.wmf +24 VDC ANN-RLY Figure 1.
Accessories Product Description Examples: • FACP Input programmed to Zone 33 goes into alarm, the programmed message for Zone 33 [Message 1, 2, 3, 4 or 5] will play over the ACC-25/50ZS Series output circuit 1 which corresponds to FACP Zone 33.
Product Description Getting Started 1.8.7 Legacy ACS Annunciators ! WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The legacy ACS annunciators may not be used if new ANN-BUS annunciators are being used due to incompatible serial communication protocols. ACM Series LED Zone Type Annunciators The ACM Series Annunciators remotely display alarm and trouble status as well as system status.
Getting Started Product Description • Enter Autoprogramming (refer to “Autoprogram” on page 66). • Resolve Programming Conflicts. • Go to Point Program to Enter Specific Data (refer to “Point Program” on page 67). Use the right and left arrow keys to navigate between devices.
Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage. Mount the cabinet in a clean, dry, vibration-free area where extreme temperatures are not encountered.
Mounting Installation mounting tab holes Main Circuit Board on Chassis 1 2 ACK/STEP 1st DEF ABC 6 EVENT 9 TUV ALARM SILENCE CLR ENTER MNO JKL ESC # DRILL HOLD 2 SEC WXY MODE RESET -/. RECALL grounding stud: attach solid earth ground wire (refer to “AC Power and Earth Ground Connection” on page 46) mounting tabs mounting slots 9600lsbrdinbox.wmf mounting studs FACP Backbox Figure 2.
Installation Mounting 3.37 cm 1.325“ 2.00“ 5.1 cm 2.00“ 2.00“ 2.00“ 2.00“ 2.00“ 2.00“ 1.625“ (4.128 cm) Semi-Flush Mounting Do not recess box more than 3.875” into wall to avoid covering venting holes on top of box. Hinge Slot for optional Dress Panel 16.65“ (42.29 cm) 4.13 cm 1.625“ 2.325“ (5.91 cm) 4.13 cm 1.625“ 7.0 cm 2.75“ 3.37 cm 1.325“ 4.1 cm 1.625“ 12.00“ (30.48 cm) 4.1cm 1.625“ 1.25“ (3.2 cm) 12.13 cm 4.775“ 12.13cm 4.775" 6.0“ 15.24 cm 16.0“ 40.64 cm 29.95 cm 11.792“ 15.
Mounting Installation Top Depth = 5.207" (13.23 cm) Door = 16.821" (42.73 cm) Backbox = 16.65" (42.29 cm) Depth = 5.325" (13.526 cm) Door = 19.26" (48.92 cm) Backbox = 19.0" (48.26 cm) Left Side Right Side Figure 2.3 FACP Cabinet Dimensions MS-9600LS Series Manual — P/N 52646:B2 2/12/2010 9600cabnew.
Installation Power 2.2 Power ! WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCONNECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED. Primary power required for the FACP is 120 VAC, 60 Hz, 3.0 amps for 120 VAC the MS-9600LS(C) and MS-9600UDLS or 240 VAC, 50 Hz, 1.
Relays Installation 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited. Power-limited Nonresettable Power #1 Power-limited Nonresettable Power #2 1.5 amperes max., 24 VDC nominal 1.5 amperes max. , 24 VDC nominal filtered, nonresettable power can be filtered, nonresettable power can be drawn drawn from TB3 Terminals 3(+) and 4(-) from TB3 Terminals 5(+) and 6(-) 9600tb3.wmf Power-limited Resettable Power 1.5 amperes max.
Installation Notification Appliance Circuits The following sections describe the configuration and wiring of Style Y and Style Z Notification Appliance Circuits on the FACP main circuit board. The NACs are configured for Style Y (Class B) from the factory. Refer to “Configuring NACs” on page 48 for information on changing the NAC configuration to Style Z (Class A) and preparing the NACKEY configuration card located in JP8, when installing a 4XTMF Transmitter Module. 2.4.
Notification Appliance Circuits Installation 2.4.2 Style Y (Class B) NAC Wiring 4 Style Y (Class B) Notification Appliance Circuits, supervised and power-limited - 4.7K ohm, ½ watt P/N:71252 UL-listed NAC 1 NAC 3 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Notification Appliance Circuit polarity shown in alarm state Dummy Load all unused circuit circuit number 9600nacy.wmf Polarized Horns Polarized Horns TB4 Figure 2.7 NAC Style Y (Class B) Wiring 2.4.
Installation Power-limited Wiring Requirements 2.5 Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower-limited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits. A typical wiring diagram for the FACP is shown below.
Optional Modules and Devices Installation 2.6 Optional Modules and Devices ! WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. FACP Keypad/Display Removal Removal of the keypad/display is normally not necessary.
Installation Optional Modules and Devices 2.6.1 DACT-UD2 Installation ! WARNING: RISK OF ELECTRICAL SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. The DACT-UD2 Digital Alarm Communicator/Transmitter, which is supplied standard with the MS-9600UDLS/E, transmits system status to UL listed Central Station receivers via the public switched telephone network.
Optional Modules and Devices Installation The following steps must be followed when installing the DACT-UD2 module: 1. Remove all power (AC and DC) from FACP before proceeding with installation 2. Remove all main circuit board mounting screws (6 locations) and the 4XTMF module standoffs (2 locations), unplug the power supply cable from J1 and lift the main circuit board assembly off the chassis (refer to Figure 2.10) 3.
Installation Optional Modules and Devices Mounting Screw Mounting Screw 96dialx3.wmf male/female standoff Figure 2.13 DACT-UD2 Installation on Standoffs 8. Reinstall Keypad/Display on the main circuit board by positioning the unit over the appropriate standoffs and securing with screws which were loosened in step 3 9. Remount the main circuit board assembly to the chassis using screws and standoffs in their original locations. Plug in the power supply cable at J1 on the main circuit board 10.
Optional Modules and Devices Installation Primary Lines Incoming Telco Phone Lines Secondary Lines Incoming Telco Phone Lines Ring Tip Ring Green Wire Tip Green Wire Red Wire Ring To premises phones Red Wire Ring To premises phones Tip Tip Note: Shorting bars inside RJ31X Jack removed during male plug insertion Secondary Phone Line SEC 7 foot cable (MCBL-7) order separately Primary Phone Line PRI Male Plug Connectors CAUTION: It is critical that the DACT-UD2 be located as the first device on
Installation Optional Modules and Devices Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connection to a polarity reversal circuit or a Remote Station receiving unit having compatible ratings: Maximum load for each circuit: 10 mA Reverse polarity output voltage: 24 VDC Remote Alarm and Remote Trouble wiring can leave the building Before installing the module, place the disconnect switch to the right (disconnect) position to prevent accidental activation of the municipal
Optional Modules and Devices Installation 8. When the installation has been complete, enable the 4XTMF module by sliding the disconnect switch to the left 9. Test system for proper operation Standoff Standoff J10 & J11 Connectors Cut Jumper JP6 FACP 9604xtm1.wmf 4XTMF Figure 2.16 4XTMF Connectors to FACP Connectors NOTE: Jumper JP5 on the FACP main circuit board can be used to configure the FACP supervisory relay for operation with the 4XTMF module.
Installation Optional Modules and Devices 3. Carefully plug connector J3 on the SLC-2LS module into connector J3 on the MS-9600LS/MS-9600UDLS main circuit board, being careful not to bend any pins 4. Secure the SLC-2LS Expander Module to the four standoffs installed in step 2 with the four supplied screws (or the screws removed in step 2) 5. Connect the SLC wiring and devices to TB8 on the SLC Expander Module. Refer to the SLC Wiring Manual for wiring information 6.
Optional Modules and Devices Installation installation details. Refer to “ANN-BUS Options” on page 121 for programming information. ! CAUTION: POSSIBLE EQUIPMENT DAMAGE DO NOT CONNECT A PRINTER OR PC TO THE FACP IF A GROUND FAULT (ZERO IMPEDANCE TO GROUND) EXISTS ON THE CONTROL PANEL. CIRCUIT DAMAGE MAY RESULT. REMOVE ALL POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY WIRING. Installation Remote printers and PCs require separate primary power.
Installation Optional Modules and Devices Legacy ACM Series Annunciators ACM and AFM Series Annunciators provide visual indications of FACP status in remote locations. Refer to the appropriate annunciator manual for information on installation, wiring and operation.
Section 3: Programming 3.1 Programming Data Entry Programming can be accomplished using the FACP keypad or by connecting an optional standard computer keyboard. The keyboard can be connected to the PS-2 connector J7 on the control panel main circuit board. Local or remote programming and editing can also be accomplished using the DACT-UD2 Digital Alarm Communicator/Transmitter which is optional for the MS-9600LS and supplied standard with the MS-9600UDLS.
Programming User Programming 3.2 User Programming The FACP is completely field programmable and requires no special software skills. While programming the FACP, the fire protection capabilities of the control panel are enabled. Programming mode will time-out following 10 minutes of inactivity.
Initial Power-up Programming Exit Programming or Read Status The programmer can exit Read Status or Programming mode by repeatedly pressing the keypad ESC (Escape) key until the display reads System All Normal. Ten minutes of inactivity will also cause the FACP to exit Programming mode. Note that the data which is entered during Programming mode is not saved until the programmer exits this mode by repeatedly pressing the ‘ESC’ key.
Programming Programming and Passwords Change” on page 135. If an invalid password is entered, the blinking cursor will return to the first password character position. To exit Programming or Read Status mode at any time, press the ESC (Escape) key repeatedly. Note that Programming mode must be exited using the ESC key in order to store the program data entered during this mode. If the Reset key is pressed or power is lost before exiting Programming mode, the data just entered will not be saved.
Master Programming Level Programming 3.6 Master Programming Level When the Master Program Level password is entered, the control panel will enter user Programming mode. In this mode, the piezo sounder remains off, the trouble relay is activated and the system Trouble LED flashes until Programming mode is exited.
Programming Master Programming Level 3.6.1 Autoprogram PROGRAMMING 1=AUTOPROGRAM 2=POINT PROGRAM 3=ZONE SETUP Programming Screen #1 Pressing 1 while viewing Programming Screen #1, will select the Autoprogram option, which prompts the control panel to poll all devices installed on one or both SLC loops. The primary purpose of autoprogramming is to allow the installer a fast and easy way to bring the system on-line as quickly as possible.
Master Programming Level Programming 3.6.2 Point Program PROGRAMMING 1=AUTOPROGRAM 2=POINT PROGRAM 3=ZONE SETUP Programming Screen #1 The Point Program option allows the programmer to add a new addressable device to an SLC loop, delete an existing device from a loop or change the programming for an existing device.
Programming Master Programming Level A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit detector address, such as 005. When the last digit is keyed-in, the following screen will be displayed: DETECTOR TYPE 1=SMOKE(PHOTO) 2=USER-DEFINED-1 3=SMOKE(ION) Press the down arrow key to view additional choices. Press the number corresponding to the desired selection to program that type to the newly added detector.
Master Programming Level Programming Edit Detector The programmer can change a detectors existing or factory default programming by pressing 3 in the Detector Screen. The following screen will be displayed: EDIT DETECTOR ENTER POINT ADDRESS *** Edit Detector Screen A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit detector address, such as 017.
Programming Master Programming Level If the selected address has been added to programming and a detector (such as a photoelectric detector) with the selected address is physically installed on the SLC and is communicating with the control panel, the following will be displayed: NORMAL SMOKE (PHOTO) ********************* ZNNN V 1D017 Edit Detector Screen #1 To change the programming for the displayed detector, press the keyboard ‘down’ arrow key to view the Edit Detector screens.
Master Programming Level Programming The following examples show the editing of a photoelectric smoke detector with address 017, located on the first SLC loop: EDIT DETECTOR 1D017 1=ENABLED YES 2=TYPE SMOKE(PHOTO) 3=VERIFICATION OFF Edit Detector Screen #2 EDIT DETECTOR 1D017 1=WALKTEST NO 2=PAS NO 3=PRE-SIGNAL NO Edit Detector Screen #3 EDIT DETECTOR 1D017 1=ZONE ASSIGNMENT 00 ** ** ** ** Edit Detector Screen #4 EDIT DETECTOR 1D017 1=NOUN/ADJECTIVE 2=DESCRIPTION ******************** Edit Detector Scr
Programming Master Programming Level Pressing the down arrow key will display additional detector types as indicated in the following table: Detector Type Smoke Photo User-Defined-1 Smoke Ion User-Defined-2 Heat Detect User-Defined-3 Smoke DuctP User-Defined-4 Photo w/Heat User-Defined-5 Duct-Superv User-Defined-6 Photo-SupervAR User-Defined-7 ADAPT User-Defined-8 Beam User-Defined-9 Action When Activated Fire Alarm same as previous (Smoke Photo) Fire Alarm same as previous (Smoke Ion) Fire Alarm same as
Master Programming Level Programming • Program the desired zone or zones to be activated by this detector, in this example Z001 • Program an output, such as a control module that is to be activated by detector 005 by assigning the same zone to it; in this example Z001 • Program an output, such as a control module, for PAS activation by assigning zone Z97 to it.
Programming Master Programming Level Note that Z** represents the Zone Number(s) corresponding to this device. The factory default for an unprogrammed device is Z00 for general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the two digit number corresponding to the zone that is to be assigned to this device. The cursor moves to the next Z** designation. Continue entering zone assignments or the remaining zones can be left blank or programmed as general alarm zone Z00.
Master Programming Level 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number corresponding to the adjective that is to be used as a descriptor for the location of the detector currently being programmed.
Programming 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number corresponding to the noun that is to be used as a descriptor for the location of the detector currently being programmed.
Master Programming Level 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Programming Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the previous Adjective and Noun Screens. The new screens will list custom Adjectives and Nouns which have been programmed into the control panel using the PS-Tools programming kit. These descriptors are selected as described in the previous sections.
Programming Master Programming Level 3. With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305. 4. Press the right arrow key to advance the zone field. 5. Select a zone number from 00 to 99. Z00 (default zone) is the general alarm zone. Z01 through Z99 may be selected to link software zones.
Master Programming Level Programming Pressing 1 for Control Module or 2 for Monitor Module will cause the following screen to be displayed: ADD MODULE MODULE# 005 IS ADDED Add Module Screen #3 The programmer can continue adding modules by pressing the ESC or left arrow key which will return the display to the Add Module Screen #1.
Programming Master Programming Level A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 012. When the last digit is keyed-in, if the selected address has not been added to programming, a screen showing information about a device that is installed with a lower address, closest to the selected address, will be displayed.
Master Programming Level Programming If the selected address corresponds to a monitor module, a screen displaying information about the module with the selected address will be displayed as illustrated in the following: NORMAL MONITOR ZNNN 1M012 EDIT MONITOR 1M012 1=ENABLED YES 2=TYPE MONITOR Edit Monitor Screen #2 EDIT MONITOR 1=PRE-SIGNAL 1M012 NO Edit Monitor Screen #3 EDIT MONITOR 1M012 1=WALKTEST YES 2=ZONE ASSIGNMENT 00 ** ** ** ** Edit Monitor Screen #4 EDIT MONITOR 1M012 1=ADJEC
Programming EDIT MONITOR 1=ENABLED 2=TYPE MONITOR Edit Monitor Screen #2 Master Programming Level Type Monitor The FACP response to the activation of a user-defined type is the same as most previous standard types in the list, thus allowing a variety of user-defined types and responses. To select the type of monitor module being programmed, press the 2 key while viewing the Edit Monitor Screen #2.
Master Programming Level Programming Monitor module type selection will affect the function of the point as follows: Monitor Type Pull-Station User-Defined-1 Waterflow User-Defined-2 Monitor User-Defined-3 Future Future Smoke-Conventional1 User-Defined-5 Heat-Conventional User-Defined-6 Medic-Alert2 User-Defined-7 Hazard-Alert2 User-Defined-8 Tornado-Alert2 User-Defined-9 Phone User-Defined-10 Tamper User-Defined-11 Supervisory User-Defined-12 Supervisory-AR3 User-Defined-13 HVAC OVRRIDE4 Power-Monitor Us
Programming EDIT MONITOR 1=PRE-SIGNAL Edit Monitor Screen #3 Master Programming Level Pre-signal To enable the Pre-signal feature, press 1 while viewing Edit Monitor Screen #3 until the display reads Pre-signal Yes. Each press of the 1 key will cause the display to toggle between Pre-signal Yes and Pre-signal No. Refer to “Presignal” on page 158 for additional information.
Master Programming Level 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number corresponding to the adjective that is to be used as a descriptor for the location of the monitor module currently being programmed.
Programming 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number corresponding to the noun that is to be used as a descriptor for the location of the monitor module currently being programmed.
Master Programming Level EDIT MONITOR 1=NOUN/ADJECTIVE 2=DESCRIPTION ***************** Edit Monitor Screen #5 Programming Description The Description selection allows the programmer to enter additional information about the monitor module currently being programmed. This information will be displayed as part of the device label on the LCD display.
Programming Master Programming Level Edit Module Screen for Control Modules MODULES 1=ADD 2=DELETE 3=EDIT The programmer can change a module’s existing or factory default programming by pressing 3 in the Modules Screen. The following screen will be displayed: EDIT MODULE ENTER MODULE ADDRESS *** Modules Screen Edit Module Screen A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 002.
Master Programming Level Programming To change the programming for the displayed module, press the keyboard down arrow key to view the following Edit Control screens: EDIT CONTROL 1=ENABLED YES 2=TYPE CONTROL 3=SILENCEABLE YES Edit Control Screen #2 EDIT CONTROL 1=WALKTEST YES 2=ZONE ASSIGNMENT 00 ** ** ** ** Edit Control Screen #3 EDIT CONTROL 1=NOUN/ADJECTIVE 2=DESCRIPTION ******************** Edit Control Screen #4 Enable/Disable Module EDIT CONTROL 1=ENABLED 2=TYPE 3=SILENCEABLE Edit Control Scr
Programming Master Programming Level The following table contains control module type codes and their functions which are displayed in the Control Type screens: Control Type Special Function Bell Circuit NAC Type - supervised Horn Circuit NAC Type - supervised Sounders NAC Type - supervised Relay Ignore Open Circuit Strobe Circuit NAC Type - supervised Control NAC Type - supervised Resettable HVAC Power1 SHUTDN 2 Relay Type - Ignore Open Circuit Relay Type - Ignore Open Circuit 1 When us
Master Programming Level Programming remaining zones can be left blank or programmed as general alarm zones Z00. When all desired changes have been made, press the Enter key to store the zone assignments. The display will return to the Edit Control Screen #3. EDIT CONTROL 1=NOUN/ADJECTIVE 2=DESCRIPTION Edit Control Screen #4 Noun/Adjective The Noun/Adjective selection allows the programmer to enter specific descriptors about the control module currently being programmed.
Programming 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number corresponding to the adjective that is to be used as a descriptor for the location of the control module currently being programmed.
Master Programming Level 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number corresponding to the noun that is to be used as a descriptor for the location of the control module currently being programmed.
Programming EDIT CONTROL 1=ADJECTIVE/NOUN 2=DESCRIPTION Edit Control Screen #4 Master Programming Level Description The Description selection allows the programmer to enter additional information about the control module currently being programmed. This information will be displayed as part of the device label on the display.
Master Programming Level Programming 3.6.
Programming ZONE SETUP 1=ENABLE 2=DISABLE 3=ZONE 97 98 99 Master Programming Level Disable Pressing 2 for Disable, while viewing Zone Setup Screen #1, will display the following screen: Zone Setup Screen #1 Z ZONE TO DISABLE Disable Screen This screen allows the programmer to disable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to enter a two digit zone number (01 - 99).
Master Programming Level ZONE SETUP 1=ZONES INSTALLED 2=ZONES ENABLED 3=ZONES DISABLED Programming Zones Installed Pressing 1 for Zones Installed, while viewing Zone Setup Screen #2, will display a screen similar to the following: Zone Setup Screen #2 ZONES INSTALLED 00 01 02 03 04 05 Zones Installed Screen This display will show all of the zones that have been programmed into the control panel.
Programming ZONE SETUP 1=ZONE TYPES 2=ZONES AVAILABLE 3=ZONE MESSAGE Zone Setup Screen #3 Master Programming Level Zone Type Zone Types must be programmed only if a DACT, programmed for zone reporting, is installed on the control panel.
Master Programming Level ZONE SETUP 1=ZONE TYPES 2=ZONES AVAILABLE 3=ZONE MESSAGE Programming Zones Available Pressing 2 while viewing Zone Setup Screen #3 will display the following screen: ZONES AVAILABLE 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 Zone Setup Screen #3 The display will show all of the zones that are still available for programming.
Programming Master Programming Level Loop Protocol Loop Protocol refers to the SLC loop mode of operation. Refer to “Wire Requirements” on page 196 for wire specifications based upon SLC protocol. Two modes of operation are available: LiteSpeed and CLIP mode. CLIP mode (Classic Loop Interface Protocol) is used for the older legacy addressable devices such as the M300 Series modules and detectors.
Master Programming Level PROGRAMMING 1=LOOP SETUP 2=SYSTEM SETUP 3=VERIFY LOOPS Programming Pressing 2 for System Setup, while viewing Programming Screen #2, will cause the following screens to be displayed: SYSTEM SETUP 1=TROUBLE REM OFF 2=BANNER 3=TIME-DATE Programming Screen #2 System Setup Screen #1 SYSTEM SETUP 1=TIMERS 2=NAC 3=RELAYS System Setup Screen #2 SYSTEM SETUP 1=CANADIAN OPT. OFF 2=WATERFLOW SIL.
Programming BANNER 1=FACTORY 2=USER DEFINED Banner Screen Master Programming Level Pressing 1 while viewing the Banner Screen will select the blank factory default banner setting and display the following screen: FACTORY BANNER Factory Banner Screen Pressing the Enter key will store this selection in nonvolatile memory and return the display to the Banner Screen.
Master Programming Level SYSTEM SETUP 1=TROUBLE REM 2=BANNER 3=TIME-DATE Programming Time-Date The control panel time and date can be changed by pressing 3 while viewing the System Setup Screen #1. The following screen will be displayed: System Setup Screen #1 TIME AND DATE 1=TIME 10:00 AM 2=DATE 02-04-2010 3=CLOCK FORMAT 12HR Time-Date Screen #1 TIME AND DATE 1=DAYLIGHT SAVINGS Time-Date Screen #2 Time To change the time, press 1 while viewing the Time-Date Screen.
Programming Master Programming Level digit is entered. After the last year digit is entered, the display will return to the Time-Date Screen which will show the new date entry. If an error is made while entering a digit, press the CLR key to delete the entire entry and beginning again. Clock Format The clock can be configured to display 12 hour (AM & PM) or 24 hour (military) time. Pressing 3 while viewing the Time-Date screen will cause the display to toggle between 12HR and 24HR.
Master Programming Level SYSTEM SETUP 1=TIMERS 2=NAC 3=RELAYS Programming Timers Timer delays for PAS, Pre-signal and waterflow activation can be programmed by pressing 1 while viewing System Setup Screen #2.
Programming Master Programming Level A flashing cursor is positioned in the lower left corner of the display. Enter a delay time consisting of three digits, such as 009 for nine seconds. Upon entering the third digit, the time delay will be stored in the control panel memory and the display will return to the Delay Screen which will indicate the new delay time. Note that the FACP can be programmed for either PAS or Pre-signal operation, not both.
Master Programming Level Programming Pressing 2 while viewing AC Loss Delay Screen #1 will display the following screen: AC LOSS DELAY RANGE 00-23 AC Loss Delay Screen #2 A flashing cursor will appear in the lower left corner of the display. The factory default setting is 02 hours. Type the two digit AC loss reporting delay in hours (00 to 23 hour delay). When the second digit is entered, the display will return to AC Loss Delay Screen #1.
Programming Master Programming Level The following screens will be displayed for either selection: NAC # 1=ENABLED 2=TYPE 3=SILENCEABLE YES BELL YES NAC Screen #1 NAC # 1=AUTO SILENCE 00 2=CODING TEMPORAL NAC Screen #2 NAC # 1=ZONE 00 00 00 00 00 2=SIL INHIBITED NO NAC Screen #3 NAC # 1=SYNC TYPE S NAC Screen #4 Enabled Pressing 1 while viewing NAC Screen #1 will cause the display to change to Enabled No. This will prevent the selected main circuit board NAC from activating its devices.
Master Programming Level NAC # 1=ENABLED 2=TYPE 3=SILENCEABLE Programming Type The main circuit board NAC type can be programmed by pressing 2 while viewing NAC Screen #1. The following screen will be displayed. Press the down arrow key to view additional screens: NAC Screen #1 NAC TYPE 1=BELL 2=HORN 3=STROBE Type Screen #1 Select the NAC device type by pressing the number corresponding to the type in the appropriate screen. When the selection is made, the display will return to NAC Screen #1.
Programming NAC # 1=AUTO SILENCE 2=CODING TEMPORAL NAC Screen #2 Master Programming Level Auto Silence The Auto Silence feature, when enabled, automatically silences all main circuit board silenceable notification appliances after a programmed length of time. To enable this feature and program the time delay before Auto Silence activation, press 1 while viewing NAC Screen #2.
Master Programming Level Programming The programmer can select the notification appliance output by pressing the number corresponding to the desired output.
Programming Master Programming Level Note that Z** represents the Zone Number(s) corresponding to the selected NAC. The factory default for an unprogrammed device is Z00 for general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the two digit number corresponding to the zone that is to be assigned to this NAC. The cursor moves to the next Z** designation. Continue entering zone assignments or the remaining zones can be left blank or programmed as general alarm zone Z00.
Master Programming Level Programming To program Relay 1 or Relay 3, press the number corresponding to the selected relay. Note that Relay 2 is fixed as a Trouble relay. Selecting Relay 2 will have no effect on its programming.
Programming Master Programming Level The Canadian Options configures the FACP with the following as required by Canada: • The following monitor module type codes are not available: • monitor • non-latching supervisory • non-latching drill • non-latching process monitor • process monitor • hazard • tornado • medical alert • The auto-silence timer is fixed at 20 minutes and cannot be changed. • Addressable ionization smoke detector sensitivity is automatically monitored using Canadian specifications.
Master Programming Level Programming 3.6.7 History PROGRAMMING 1=HISTORY 2=WALKTEST 3=OPTION MODULES The History option allows an authorized user to view or erase events which have occurred in the control panel.
Programming Master Programming Level 3.6.8 Walktest PROGRAMMING 1=HISTORY 2=WALKTEST 3=OPTION MODULES Walktest allows an individual to test the fire alarm system without the necessity to reset the control panel after each device activation.
Master Programming Level Programming Pressing 2 for View Points while viewing the Unit In Walktest screen will display one of the following screens: NO POINTS IN SYSTEM OR UNTESTED POINTS 010 1D001 SMOKE (PHOTO) ********************* NOT TESTED If the system has no points installed, the first screen will be displayed. If points are installed, the second screen will be displayed, which allows the viewing of all untested system points and their status relating to the current walktest session.
Programming Master Programming Level Pressing 3 while viewing Programming Screen #3 will display the following screen: OPTION MODULES 1=ANNUNCIATORS/UDACT 2=ONBOARD DACT 3=PRINTER/PC PR4800 Options Screen Note that PR4800 in the display indicates that a supervised printer, configured for 4800 baud, has been previously programmed into the system.
Master Programming Level Programming ACS Options ANNUNCIATORS 1=TERM OPTIONS 2=ACS OPTIONS 3=ANN-BUS OPTIONS Pressing 2 for ACS Options while viewing the Annunciators screen, will display the following screen: Annunciator Screen ACS OPTIONS 1=ACS ENABLED 2=ACS INSTALLED 3=UDACT NO NO Pressing 1 while viewing the ACS Options screen will cause the display to toggle between ACS Enabled Yes and ACS Enabled No. To install an ACS annunciator, the display must read ACS Enabled Yes.
Programming Master Programming Level Annunciator addressing is specific to the FACP control panel. The following table describes the annunciator addresses and the corresponding addressable devices that will be annunciated at each annunciator address.
Master Programming Level Programming ANN-BUS Options ANNUNCIATORS 1=TERM OPTIONS 2=ACS OPTIONS 3=ANN-BUS OPTIONS Pressing 3 for ANN-BUS Options, while viewing the Annunciators screen, will cause the following screens to be displayed:.
Programming Master Programming Level Pressing 1 for Type will display the following screens: ANN-BUS MODULE TYPE 1=NOT INSTALLED 2=ANN-80 MODULE 3=ANN-I/O MODULE Module Type Screen #1 ANN-BUS MODULE TYPE 1=ANN-S/PG MODULE 2=ANN-LED MODULE 3=ANN-RLY MODULE Module Type Screen #2 ANN-BUS MODULE TYPE 1=ANN-AUDIO Module Type Screen #3 Press the number corresponding to the module type that is installed with the selected address.
Master Programming Level Programming ANN-I/O Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-I/O option is selected will display the following screen: ANN-I/O ADDR # SLC 1 MOD 001-030 ACTIVE LEDS ONLY ANN-I/O Address Screen #1 ANN-I/O ADDR # 1=POINT/ZONE POINT ANN-I/O Address Screen #2 ANN-I/O ADDR # 1=RANGE PT001-030 2=DET/MOD MOD 3=SLC LOOP # 2 ANN-I/O Address Screen #3 The first screen indicates that the ANN-I/O at the selected ANN-BUS address is programmed
Programming 124 Master Programming Level 4 Trouble Zone 33 Zone 73 5 Alarm Silenced Zone 34 Zone 74 6 Earth Fault Zone 35 Zone 75 7 Battery Fault Zone 36 Zone 76 8 Charger Fault Zone 37 Zone 77 9 NAC Fault Zone 38 Zone 78 10 Disabled Zone 39 Zone 79 11 Zone 00 Zone 40 Zone 80 12 Zone 01 Zone 41 Zone 81 13 Zone 02 Zone 42 Zone 82 14 Zone 03 Zone 43 Zone 83 15 Zone 04 Zone 44 Zone 84 16 Zone 05 Zone 45 Zone 85 17 Zone 06 Zone 46 Zone 86 18 Zone 07 Zo
Master Programming Level Programming ANN-I/O Point Option If Point is selected as the module option, the first ten LEDs on the first ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
Programming Master Programming Level ANN-LED Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-LED option is selected will display the following screen: ANN-LED ADDR # LOOP1 DET 1-10 ALARM,SUPERV,TBL ANN-LED Address Screen #1 ANN-LED ADDR # 1=POINT/ZONE 2=ALARM/ATS ANN-LED Address Screen #2 ANN-LED ADDR # 1=RANGE 2=DET/MOD 3=LOOP# ANN-LED Address Screen #3 The first screen indicates that the ANN-LED at the selected ANN-BUS address is programmed to annunciate Alarm
Master Programming Level Programming ANN-LED Zone Option - Alarm Only (for use with ANN-RLED module) If Zone is selected as the module option, and the module is programmed to annunciate alarms only, the first ten LEDs on the first ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining modules will display the active/alarm status of each zone in the Zone Range programmed for that particular module.
Programming Master Programming Level ANN-LED Zone Option - Alarm, Trouble and Supervisory If Zone is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first ANN-LED module will display the system status information.
Master Programming Level Programming ANN-LED Point Option - Alarm Only (for use with ANN-RLED module) If Point is selected as the module option and the module is programmed to annunciate alarms only, the first ten LEDs on the first ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
Programming Master Programming Level ANN-LED Point Option - Alarm, Trouble and Supervisory If Point is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first ANN-LED module will display the system status information.
Master Programming Level Programming ANN-RLY Options Pressing 2 for Module Options while viewing ANN-BUS Address Screen when the ANN-RLY option is selected will cause the following screen to be displayed: ANN-RLY - ADDR. # 1=RELAY 1 ZONE 00 2=RELAY 2 ZONE 01 3=RELAY 3 ZONE 02 ANN-RLY Options Screen The ANN-RLY module provides ten Form-C relays which can be programmed for various functions. The initial screen displays Relays 1 through 3.
Programming Master Programming Level ANN-S/PG (Print) Options ANN-BUS 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS ANN-BUS Screen #2 The Print option allows the programmer to configure the optional printer.
Master Programming Level Programming ANN-80 Options ANN-BUS 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS ANN-BUS Screen #2 Pressing 2 while viewing ANN-BUS screen #2 will display the following screen: ANN-80 OPTIONS 1=PIEZO ENABLE 2=LOCK ENABLE 3=ACK BTN ENABLE ANN-80 Options Screen #1 ANN-80 OPTIONS 1=SIL BTN ENABLE 2=RST BTN ENABLE 3=DRL BTN ENABLE ANN-80 Options Screen #2 The Piezo Enable option allows the programmer to select whether the piezo sounder on any installed ANN-80 module will ever sound.
Programming Master Programming Level On Board DACT OPTION MODULES 1=ANNUNCIATORS/UDACT 2=ON BOARD DACT 3=PRINTER/PC NO Option Module Screen The Onboard DACT (Digital Alarm Communicator/Transmitter) provides communication to a Central Station. Pressing 2 while viewing the Option Module Screen will allow programming of the Onboard DACT. Refer to the DACT-UD2 Installation and Programming Manual Document #53037 for detailed information on installing and programming this option.
Master Programming Level Programming 3.6.10 Password Change PROGRAMMING 1=PASSWORD CHANGE 2=CLEAR PROGRAM 3=PROGRAM CHECK The factory set passwords, which have been programmed into the control panel, can be changed by selecting the Password Change option.
Programming Master Programming Level 3.6.11 Clear Program PROGRAMMING 1=PASSWORD CHANGE 2=CLEAR PROGRAM 3=PROGRAM CHECK Programming Screen #4 Pressing 2 while viewing Programming Screen #4, will select the Clear Program option.
Master Programming Level Programming 3.6.12 Program Check PROGRAMMING 1=PASSWORD CHANGE 2=CLEAR PROGRAM 3=PROGRAM CHECK Programming Screen #4 The Program Check feature allows the programmer to view the zones which have been programmed to the Notification Appliance Circuits on the control panel but have not been programmed to Initiating Devices as well as other circuits with no input or output correlations.
Programming Maintenance Programming Level Pressing 3 while viewing Program Check screen will cause a screen similar to the following to be displayed: ZONES NO OUTPUT 05 07 09 10 11 1D001 The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00).
Maintenance Programming Level Programming Note that in the preceding screens, an arrow appears to inform the programmer that additional options can be viewed by pressing the keypad down arrow key, as shown in the following screen. PROGRAMMING 1=WALKTEST 2=SYSTEM 3=ZONE SETUP 3.7.
Programming Maintenance Programming Level A flashing cursor will appear in the bottom left corner of the display, prompting for the three digit device address. When the third digit is enter, 001 for example, a screen will appear which will allow enabling or disabling of the selected point, as illustrated in the following example: EDIT DETECTOR 1D001 1=ENABLED YES Enable/Disable Select Screen Pressing 1 repeatedly will cause the display to toggle between Enabled Yes and Enabled No. 3.7.
Maintenance Programming Level Programming Pressing 2 while viewing the History Screen will cause the following screen to be displayed: ERASE HISTORY PROCEED ? 1=YES 2=NO Erase History Screen Pressing 1 while viewing the Erase History Screen will cause the message ERASING HISTORY, PLEASE WAIT to be displayed. The display will then return to the History Screen. Pressing 2 will cause the display to return to the History Screen without erasing the History file. 3.7.
Programming Maintenance Programming Level Pressing 2 while viewing the Program Check screen will display a screen similar to the following: ZONES NO INPUT 05 07 09 10 11 1M001 The Zone No Input screen allows the programmer to view the zones which have not been programmed to at least one input device (not including general alarm Zone 00).
Maintenance Programming Level Programming 3.7.5 System To program the time and date into the control panel, press 2 while viewing Maintenance Screen #2.
Programming Maintenance Programming Level To change the date, press 2 while viewing the Time and Date Screen. The following screen will be displayed: ENTER DATE MONTH DAY YEAR 01-01-2010 Date Screen A flashing cursor will appear on the left side of the display. Enter the two digit month, two digit day and four digit year. The cursor will move one position to the right after each entry.
Maintenance Programming Level Programming Pressing 1 while viewing Zone Setup screen #1 will display the following screen: Z ZONE TO ENABLE Enable Screen ZONE SETUP 1=ZONES INSTALLED 2=ZONES ENABLED 3=ZONES DISABLED A flashing cursor appears to the right of the Z. To enable a zone, enter the two digit zone number (00 - 99). After the second digit is entered, the zone will be enabled and the cursor will return to the original position. The next zone to be enabled can then be entered.
Programming Maintenance Programming Level nected to the control module can be used to indicate a PAS condition in the control panel. Do not assign Zone 97 to a Notification Appliance Circuit when using this zone to indicate a PAS condition. Pressing 2 will cause the display to change to Pre-signal 98 On. Each press of the 2 key will cause the display to toggle between Pre-signal 98 On and Pre-signal 98 Off.
Maintenance Programming Level Programming Zones Disabled Pressing 3 for Zones Disabled, while viewing Zone Setup Screen #2, will display a screen similar to the following: ZONES DISABLED 03 Zones Disabled Screen This display will show all of the zones that are disabled in the control panel. Note that an up and/or down arrow may appear in the upper right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to view the additional zones.
Programming Maintenance Programming Level Zone types can be changed by pressing the keypad number key corresponding to the zone in each Zones Installed Screen. Available zone types will be displayed in the resultant screens. For example, to change the zone type for zone Z02 in the screen illustrated above, press 3.
Maintenance Programming Level Programming Zone Message Pressing 3 while viewing Zone Setup Screen #3 will display the following screen: ZONE MESSAGE 1=Z00 NO MESSAGE 2=Z01 MESSAGE 1 3=Z02 NO MESSAGE Pressing the down arrow key will display additional screens for Zones up to Z99. Press the number key corresponding to the Zone to be programmed. Screens will be displayed allowing the programmer to select Messages 1 through 5.
Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge/Step The first press of the Acknowledge/Step key silences the piezo sounder, changes flashing LEDs to steady and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file. Acknowledge also sends a silence piezo command to the optional annunciators connected to the FACP.
Normal Operation Operating Instructions Supervisory This is a yellow LED that flashes when one or more supervisory conditions occur, such as a sprinkler valve tamper condition. It illuminates steady when the Acknowledge/Step or Alarm Silence key is pressed. It turns off when the Reset key is pressed and remains off if all supervisory alarms have been cleared. Trouble This is a yellow LED that flashes when one or more trouble conditions occur.
Operating Instructions Trouble Operation 4.
Alarm Operation Operating Instructions INV ID - indicating that an incorrect device code (Type ID) has been programmed for an installed device (for example, Photo has been programmed but an Ion detector has been installed) SW TBL - indicating a module has failed the testing of its Class A switching relay • Fourth line in display: – Time; the current time in this example is 10:00A which represents 10:00 AM – Date; the current month, day and year in this example is 01 for January, 08 for the 8th day o
Operating Instructions Supervisory Operation Note that the device type, which in this example is PULL STATION, can be any other programmable alarm type. The information displayed in the above example provides the following information: • First line in display: – The type of event; in this example ALARM indicating an alarm condition – Device type identifier; in this example, PULL STATION indicates a manual pull box.
Process Monitor Operation Operating Instructions A typical Supervisory event would be displayed as illustrated in the following: ACTIVE SUPERVISORY Z000 10:00A 010810 1M001 Note that, like alarms, supervisory signals latch (except when programmed for supervisory autoresettable) and can be assigned to software zones. Supervisory alarms do not cause resound as do other alarm conditions.
Operating Instructions Medical Alert Condition Operation 4.
Time Functions: Real-Time Clock Operating Instructions Type Code Supervision The FACP monitors addressable hardware device codes at slow intervals. Mismatch of any type code, compared to the system program, will cause a device trouble. System Alarm Verification The control panel may be programmed to perform alarm verification to help eliminate the nuisance of false alarms. Alarm verification applies to smoke detectors only.
Operating Instructions Presignal 4.18 Presignal Presignal option programs an initiating device to delay the activation of NACs and/or control modules while allowing visual verification by a person. Once a detector or monitor module triggers an alarm, the onboard piezo sounds immediately, but the NACs are not activated for a user programmed time duration of up to three minutes. Note that the alarm relay and communicator will respond to the initial alarm immediately. In addition, Zone 98 will activate.
Special System Timers Operating Instructions • pressing the Alarm Silence or Acknowledge/Step key will start a timer which inhibits output activation for additional time delay of up to three minutes which is user programmable • second alarm occurring anytime during either time delay will cause immediate activation of all associated outputs PAS operation requires the approval of the local Authority Having Jurisdiction.
Operating Instructions Walktest all appropriate outputs and indicate the alarm condition at the FACP. If no additional detector alarms occur within 73 seconds of the first alarm (13 second Retard plus 60 second Confirmation), the timer resets and the panel is ready to verify any new detector alarms which may occur. 13 sec. 0 sec.
Read Status Operating Instructions Read Status Entry When the operator presses the control panel Enter key, the LCD will display the following: 1=READ STATUS 2=PROGRAMMING 3=REMOTE DOWNLOAD Pressing 1, while this screen is being displayed, will cause the control panel to enter the Read Status mode which allows the user to view and print the programmed features and status of the control panel.
Operating Instructions Read Status 4.22.1 System Point READ STATUS 1=SYSTEM POINT 2=ZONES 3=POWER Pressing 1 while viewing Read Status Screen #1 will cause the following screen to be displayed: READ SYSTEM POINT SELECT LOOP 1=LOOP 1 2=LOOP 2 Read Status Screen #1 The operator selects the loop containing the device to be read by pressing 1 for Loop 1 or 2 for Loop 2.
Read Status Operating Instructions Pressing the down arrow key, while viewing the screen shown on the previous page, will allow the operator to view additional programming information about the selected device, such as: • Enable/Disable Status • Device Type • Alarm Verification On/Off • Walktest Yes/No • PAS (Positive Alarm Sequence) Yes/No • Pre-Signal Yes/No • Zone Assignments (five maximum) • Chamber Reading • Adjective/Noun descriptor • Silenceable Yes/No (for control modules) 4.
Operating Instructions Read Status 4.22.3 Power Pressing 3 while viewing Read Status Screen #1 will display the following screens: POWER BATTERY 24 V RST 27.21V 25.31V Zones Screen #1 POWER CHARGER 28.36V NAC 1 -2.39V NAC 2 -2.39V Zones Screen #2 NAC 3 NAC 4 POWER -2.39V -2.39V Zones Screen #3 A real-time display of control panel voltages can be used to determine if system problems exist.
Read Status Operating Instructions 4.22.4 Trouble Reminder Pressing 1 while viewing Read Status Screen #2 will display the following screen: READ STATUS 1=TROUBLE REMINDER 2=TIMERS 3=NACS TROUBLE REMINDER TROUBLE REM ON Read Status Screen #2 The screen indicates whether the Trouble Reminder feature is On or Off. 4.22.
Operating Instructions Read Status 4.22.6 NAC Pressing 3 while viewing Read Status Screen #2 will display the following screen: NAC 1=NAC 1 3=NAC 3 2=NAC 2 4=NAC 4 Note that 3=NAC 3 and 4=NAC 4 will only be displayed if the NACKEY NAC option card is installed, in JP8 of the main circuit board, for Class B operation.
Read Status Operating Instructions 4.22.8 Program Check Pressing 2 while viewing Read Status Screen #3 will cause a screen similar to the following to be displayed: PROGRAM CHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONES NO OUTPUT Pressing 1 while viewing the Program Check screen will display a screen which will indicate if any input zones have not been programmed to one of the Notification Appliance Circuits. Use the up and down arrow keys to view all NACs.
Operating Instructions Read Status The Annunciator Screen indicates if Terminal mode options are enabled or disabled. Pressing 2 for ACS Options while viewing the Annunciator Screen allows the operator to view the ACS Options screen: ACS OPTIONS ACS ENABLED 2=ACS ADDRESSES UDACT ENABLED NO NO ACS Options Screen The ACS Options screen indicates if the ACS option has been enabled YES or disabled NO.
Read Status Operating Instructions 4.22.11 Phone Line Pressing 2 while viewing Read Status Screen #4 will display the following screen: PHONE LINE PRIMARY TOUCHTONE SECONDARY TOUCHTONE 3=SUPERV PHONE LINE The second and third lines of this screen indicate that both the Primary and Secondary phone lines have been configured for touchtone dialing operation.
Operating Instructions Read Status 4.22.13 Service Terminal Pressing 1 while viewing Read Status Screen #5 will display the following screens: READ STATUS 1=SERVICE TERMINAL 2=PRINTER/PC 3=PRINT SERVICE TERMINAL RING COUNT 05 Read Status Screen #5 Service Terminal Screen The Ring Count is displayed in the Service Terminal Screen. A Ring Count value of 00 would indicate that calling is disabled. 4.22.
Read Status Operating Instructions 4.22.15 Print To print program data or control panel status, press 3 while viewing Read Status Screen #5.
Operating Instructions Read Status Drift Compensation Drift compensation uses software algorithms that identify and compensate for long-term changes in the data readings from each addressable smoke detector. These long-term changes in detector data readings are typically caused by dirt and dust accumulation inside the smoke chamber.
Read Status Operating Instructions 4.22.16 Time-Date READ STATUS 1=TIME-DATE The operator can view the daylight savings time and the month and week when daylight savings time will begin and end.
Section 5: Power Supply Calculations 5.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: 1. Calculating the total amount of AC branch circuit current required to operate the system 2. Calculating the power supply load current for non-fire and fire alarm conditions and calculating the secondary (battery) load 3.
Calculating the System Current Draw Power Supply Calculations • ‘Secondary’ refers to the control panel’s backup batteries • All currents are given in amperes (A). Table 5.2 shows how to convert milliamperes and microamperes to full amperes. To convert... Multiply Milliamperes (mA) to amperes (A) mA x 0.001 Microamperes (µA) to amperes (A) µA x 0.000001 Example 3 mA x 0.001 = 0.003A 300 µA x 0.000001 = 0.0003 A Table 5.2 Converting to Full Amperes 5.3.2 How to Use Table 5.
Power Supply Calculations Calculating the System Current Draw Table 5.3 contains columns for calculating current draws. For each column, calculate the current and enter the total (in amperes) in the bottom row. When finished, copy the totals from Calculation Column 2 and Calculation Column 3 to Table 5.4 on page 177.
Calculating the Battery Size Power Supply Calculations 5.4 Calculating the Battery Size Use Table 5.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the control panel under the loss of AC power. Complete Table 5.4 as follows: 1. Enter the totals from Table 5.3 on page 176, Calculation Columns 2 and 3 where shown. 2. Enter the NFPA Standby and Alarm times (refer to ‘NFPA Requirements’ below). 3.
Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone. Connection of output devices (horns, bells, strobes, etc.
Correlations Software Zones Correlation of Input and Output Zones Input Devices Zones SD350 01 CMF-300 13 SD350 02 MMF-300 01 CMF-300 05 ZONE 01 CMF-300 06 MMF-302 02 CMF-300 07 CMF-300 09 MMF-302 03 CP350 03 Output Devices ZONE 02 CMF-300 08 CMF-300 10 CP300 04 SD350 05 CMF-300 11 SD350 06 SD350 07 MMF-302 04 ZONE 03 CMF-300 12 The zone correlations which are shown graphically above are also presented in Table A.1 on page 180 and Table A.2 on page 181.
Software Zones Address 01 Correlations Device Type SD350 Zone Number 1 DETECTOR ZONE ASSIGNMENT Device ADJ/NOUN Address Type FIRST HALL 51 02 SD350 1 ELEV. LOBBY 03 CP350 2 2ND FLOOR 53 04 CP350 2 ROOM 210 54 05 SD350 3 3RD FLOOR 55 06 SD350 3 MEZZANINE 56 07 SD350 3 MECH.
Correlations Software Zones Address Device Type 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 MMF-300 MMF-302 MMF-302 MMF-302 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone ADJ/NOUN Address Type Number 1 51 1, 2 52 1, 2 53 3 54 1 55 1 56 1 57 2 58 1, 2, 3 59 2 60 3 61 3 62 1 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
Software Zones Correlations DETECTOR ZONE ASSIGNMENT Address 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Table A.
Correlations Address 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 Software Zones Device Type Zone Number DETECTOR ZONE ASSIGNMENT Device ADJ/NOUN Address Type 151 152 153 154 155 156 157 158 159 Zone Number ADJ/NOUN Table A.
Software Zones Address 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Correlations Device Type MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone ADJ/NOUN Address Type Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Zone Number ADJ/NOUN Table A.
Correlations Address 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 Software Zones Device Type MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone ADJ/NOUN Address Type Number 151 152 153 154 155 156 157 158 159 Zone Number ADJ/NOUN Table A.
Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings.
Appendix C: NFPA Standard-Specific Requirements The FACP has been designed for use in commercial, industrial and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: Fire Alarm Control Panel Contains the main control board, cabinet (backbox and door), main power supply transformer and power supply.
NFPA Standard-Specific Requirements NFPA Signaling Systems for Central Station Service (Protected Premises Unit)/Remote Station The following figure illustrates an example of Central Station/Remote Station Reporting using a 411UDAC. The relay contacts from the FACP may be used to trip any dialer UL listed for Central Station/Remote Station Services. Notes: 1. Reference the 411UDAC Manual for additional information 2. Program the 411UDAC for slave operation 3.
NFPA Standard-Specific Requirements The following figure illustrates an example of Central Station/Remote Station Reporting using a 411UD. The relay contacts from the FACP may be used to trip any dialer UL listed for Central Station/Remote Station Reporting Services. Note: The Monitor Module input, which is being used to monitor the 411UD Relay #2 Output (programmed for DACT Trouble), must be programmed as ‘Trouble’ at FACP. Channel1 Channel 4 (2.
NFPA Standard-Specific Requirements NFPA 72 Auxiliary Fire Alarm System All connections are power-limited and supervised. This application is not suitable for separate transmission of sprinkler supervisory or trouble conditions. Notes: 1. 3 ohms maximum loop resistance allowed for wiring from control panel to Municipal Box. 2. Cut JP6 on the FACP main circuit board to supervise placement of 4XTMF module and circuit. 3. Cut JP5 on the FACP main circuit board to enable FACP Supervisory relay. 4.
NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: 1. Cut Jumper JP6 on the FACP main circuit board to supervise placement of the 4XTMF module. 2. Refer to “4XTMF Transmitter Module Installation” on page 55 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Fire•Lite Alarms, Inc., Instruction Manual for Remote Station Receiver Model RS82. + + - Polarity Shown is Normal Standby Power-limited (Dummy load with a 4.
NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems FACP Addressable Fire Control Panel FACP Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition. Notes: 1. Connection between the FACP and the transmitter are supervised by the transmitter. 2.
Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts NFPA Standard-Specific Requirements C.1 Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts The dry contacts of the FACP programmable relays can be used to trip a UL-864 Listed Central Station/Remote Station Transmitter. The FACP contacts must be supervised by the Central Station/Remote Station Transmitter module using End-of-Line Resistors (ELRs) with a value determined by the Transmitter manufacturer.
NFPA Standard-Specific Requirements MBT-1 Municipal Box Trip - Silenceable C.2 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box. Connect wires to two red terminals on box.
Appendix D: FACP with Keltron The following figure illustrates the connections between the FACP and Keltron Receiver/Transmitter. ! CAUTION: POSSIBLE EQUIPMENT DAMAGE FOR REASONS OF WIRING DIAGRAM CLARITY, TERMINAL DESIGNATIONS OF KELTRON MODULES ARE NOT SHOWN IN ACTUAL ORDER.
Appendix E: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Style 4) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the FACP main circuits must be carefully considered to ensure proper operation. It is important to use the correct type of wire, wire gauge and wire run length for each FACP circuit.
NAC Wiring Wire Requirements E.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-A Max. allowable wire pair length (feet) CLASS-B Max. allowable wire pair length (feet) NAC Load (Amps) Max. allowable total loop resistance (ohms) AWG 12 solid AWG 14 solid AWG 16 solid AWG 18 solid AWG 12 solid AWG 14 solid AWG 16 solid AWG 18 solid 0.25 12.72 3295 2072 1301 819 1648 1036 650 409 0.5 6.36 1648 1036 650 409 824 518 325 205 0.75 4.
Appendix F: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition. IMPORTANT! This HVAC feature is not to be used for smoke control. It is only designed to shut down fans during a fire alarm condition. F.1 Control Module Operation F.1.
Monitor Module Operation HVAC Control F.2.2 HVAC OVRRIDE The HVAC OVRRIDE type code can be assigned to any addressable monitor module for the purpose of overriding or preventing the HVAC SHUTDN control modules from activating. The HVAC OVRRIDE monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.
Appendix G: Canadian Application • The MS-9600LSC is supplied with the DP-9692 Dress Panel. • When installing and programming the FACP, the Canadian Option must be set to ON prior to any other panel programming (refer to “Canadian Option” on page 113 of the Programming Section of this manual). • ACS Series annunciators are not compatible for Canadian applications. • The LCD-80FC annunciator can be used for optional ancillary annunciation.
Index Numerics 300 Series addressable devices 20 4XTMF module 190, 191 coil resistance 55 current 55 installation 55 installation steps 56 see also Transmitter Module 15, 21 voltage 55 A AC Branch Circuit calculations 174 AC Loss Delay 106 AC Power 46 current 15 current, maximum 46 voltage 15 wiring 15, 46 Acknowledge/Step 18, 150 ACM LED annunciator 60 ACM Series see also annunciator 40 ACM-16ATF Annunciator 40 ACM-32AF Annunciator 40 ACM-8RF 14 contact rating 59 see also Relay Control Module 59 ACS LED a
D–E 202 Index Classic Loop Interface Protocol 100 CLIP Mode see also Classic Loop Interface Protocol 100 Clock Format 104 Coded Operation 157 Coding NAC 110 coding two stage operation 111 control buttons 150 control module 20 description display 94 display 88 edit 88 enable/disable 89 noun 93 noun/adjective 91, 92 silenceable 90 type 89 type codes 90 Correlations 178 current AC Power 46 availability 17 maximum 17 Current Draw Calculations 176 Detector add 67 adding description 74 delete 68 edit 69 enabl
Index F–N F FACP see also Fire Alarm Control Panel 13 Features 13 Fire Alarm Control Panel see also FACP 13 Form-C relay 19, 47, 59 G general alarm zone 84 see also zone Z00 74 ground fault 59 Maintenance 151 see also Indicators 17 Supervisory 151 Trouble 151 LED annunciator 40 Local Energy Municipal Box Service 55 Local Programming 62 Loop Setup 99 M Key Panel 18 function keys 18 service/program keys 18 keyboard and keypad 61 Keypad/Display removal and installation 51 main circuit, mounting 42 Maint
O–P Index synchronized 157 voltage drop 15 voltage, operating 15 wiring Style 47 NAC enable/disable 108 NAC options 100 NAC type 109 NACKEY card 48 N-ELR Mounting Plate 21 NFPA 72 Auxiliary Fire Alarm System 187, 190 NFPA 72 Central Station Service (Protected Premises Unit) or Remote Station Service 187 NFPA 72 Proprietary Fire Alarm System 187 NFPA 72 Proprietary Protective Signaling Systems 192 NFPA 72 Remote Station Protective Signaling System 191 NFPA Battery Requirements 177 NFPA Signaling Systems fo
Index R–S program keys see also Key Panel 18 Programming 61, 62 autoprogramming 62 exiting 63 factory default 186 Level 1 63 Level 2 63 manual 62 Master Level 1 65 modules 78 off-line computer 62 via computer keyboard 61 via panel keypad 61 Programming Levels 63 Programming Screens 63 Programming Sheet 180, 181, 182, 183, 185 Programming Utility see also PS-Tools 21 PRT/PK-CABLE for PC/Printer connection 59 PS-Tools Programming Utility 21 R Read Status 62, 161 annunciators 167, 169 exiting 63 history 167
T–Z Index Phone Line 2 169 Supervisory 154 SUPERVISORY AR 113 sync programming 108 see also synchronization 112 synchronization 157, 166 by manufacturer 112 programming 112 see also strobe synchronization 14 synchronized 157 Synchronized Signals 157 and silenceable circuits 109 System Maintenance Level 143 System Point 162 System Setup 100 T Time and Date Maintenance Level 143 Time setting 103 Time-Date setting 100, 103 Timers 100 Transmitter Module 55 see also 4XTMF module 21 TR-CE trim ring 22 Trouble
Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan. 1, 2009).
World Headquarters 1 Firelite Place Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.firelite.