System Installation Guide Prestige™ Thermostat With wireless accessories Français : voir la page 17 • Español: vea la página 33 Control for up to 3 Heat/2 Cool heat pump systems or up to 2 Heat/2 Cool conventional systems. Installation guide for: • • • THX9000 Prestige HD and Prestige SD thermostats Wireless remote control Wireless outdoor air sensor DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical shock or equipment damage.
Prestige™ Installation Guide System installation at a glance Thermostat Outdoor air sensor Remote control HVAC equipment Installation procedure 1 2 3 4 5 Mount and wire thermostat ........................................Pages 3-7 Customize thermostat (installer setup) ............................Page 8 Install batteries in wireless accessories ..........................Page 8 Link accessories to thermostat ................................Pages 9-10 Mount outdoor sensor .................................
Français : voir la page 17 • Español: vea la página 33 1 Mount and wire thermostat Pull wiring through hole in wallplate and install as shown below. Wall anchor Drywall: 3/16” hole Plaster: 7/32” hole Mounting screw Wiring Strip 1/4” insulation and connect wires to screw terminals as shown below (see wiring guides on following pages). Factory-installed jumper System wiring Wiring must comply with local electrical codes.
Prestige™ Installation Guide Wiring guide See detailed wiring guides for specific system types on following pages. Conventional Terminal Letters: C Common wire from secondary side of cooling transformer. Rc Cooling power. Connect to secondary side of cooling system transformer. R Heating power. Connect to secondary side of heating system transformer. W Heat relay (stage 1). W2 Heat relay (stage 2). Y Compressor contactor (stage 1). Y2 Compressor contactor (stage 2). G Fan relay.
Français : voir la page 17 • Español: vea la página 33 System-specific wiring guides Conventional systems See [notes] below.
Prestige™ Installation Guide System-specific wiring guides Heat pump systems See [notes] below.
Français : voir la page 17 • Español: vea la página 33 System-specific wiring guides Humidification systems See [notes] below.
Prestige™ Installation Guide 2 Customize thermostat (installer options) MENU Press MENU. Press ▼ to scroll down, then press INSTALLER OPTIONS. Enter security code when prompted. Security code is the thermostat date code (printed on back of wallplate). Or press MENU > EQUIPMENT STATUS to find code. Installer Options Press CREATE SETUP to configure all system settings one by one. Press VIEW/EDIT to select a specific function and make quick changes. (See complete list of system settings on pages 12-13.
Français : voir la page 17 • Español: vea la página 33 4 Link wireless accessories to thermostat (optional) MENU Press MENU. Press ▼ to scroll down, then press INSTALLER OPTIONS. Enter security code when prompted. Security code is the thermostat date code (printed on back of wallplate). Or press MENU > EQUIPMENT STATUS to find code. Installer Options Press ▼ to scroll down, then press WIRELESS DEVICE MANAGER.
Prestige™ Installation Guide Link remote control to thermostat (optional) CONNECT WIRELESS SETUP 1 Make sure the thermostat displays the “Add Device” timer (see page 9). 2 Press CONNECT at the remote. There will be a short delay as the remote seeks a signal from the thermostat. 3 When the screen displays “Connected,” press DONE. Press to link to another thermostat YES Press to save and exit NO CONNECT MORE? 4 Press NO at the next screen to save and exit.
Français : voir la page 17 • Español: vea la página 33 5 Install outdoor sensor (optional) Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight.
Prestige™ Installation Guide Installer setup tables Setup functions 100 110 112 130 140 150 160 165 172 174 176 180 190 200 210 220 230 240 250 260 281 285 300 310 320 330 342 345 346 350 360 365 366 367 368 369 371 372 374 379 380 383 (factory default setting listed, other options available) Language Zone number Device name Date year Date month Date day Schedule options Restore Energy Star System selection Compressor stages Heat stages Fan operation Reversing valve Backup heat External fossil fuel Compr
Français : voir la page 17 • Español: vea la página 33 Installer setup tables Setup functions 384 390 391 392 393 394 500 502 510 520 530 540 580 600 610 630 640 650 660 670 680 690 700 701 702 703 710 (factory default setting listed, other options available) Dehumidification fan control Dehumidification away mode Away mode fan operation Away mode low temp. setting Away mode high temp.
Prestige™ Installation Guide Replacing system components Thermostat After installing a new thermostat, you must re-link all accessories to the new thermostat, as described below. 1 Install and wire new thermostat (see pages 3-7) 2 Customize new thermostat (see page 8) 3 Link wireless accessories (see pages 9-10) At the remote control: • Press and hold the blank space (or arrow if present) in the lower right corner of the screen until the display changes (see page 10).
Français : voir la page 17 • Español: vea la página 33 Specifications & replacement parts Operating Ambient Temperature Thermostat: 32 to 120° F (0 to 48.9° C) Remote control: 32 to 120° F (0 to 48.
Prestige™ Installation Guide Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.
Guide d’installation du système Thermostat Prestige™ Avec accessoires sans fil Français : voir la page 17 • Español: vea la página 33 Régulation de thermopompes offrant jusqu’à 3 étages de chauffage et 2 étages de refroidissement ou de systèmes classiques offrant jusqu’à 2 étages de chauffage et 2 étages de refroidissement.
Prestige™ Installation Guide Installation du système en un coup d’oeil Thermostat Capteur d’air extérieur Télécommande Matériel de CVCA Installation 1 2 3 4 5 Installation et raccordement du thermostat ..........Pages 19-23 Personnalisation du thermostat (mode de configuration par l’installateur).. ....................Page 24 Insertion des piles dans les accessoires sans fil ..........Page 24 Connexion des accessoires au thermostat ............Pages 25-26 Installation du capteur extérieur .............
Français : voir la page 17 • Español: vea la página 33 1 Installation et raccordement du thermostat Faire passer les fils par l’ouverture dans la plaque murale et installer le thermostat comme sur l’illustration ci-dessous. Cheville d’ancrage Placoplâtre : Ouverture de 3/16 po (0.19 mm) Plâtre : Ouverture de 7/32 po (0.22 mm) Vis de fixation Raccordement électrique Dénuder l’isolant sur 1/4 po (0.
Prestige™ Installation Guide Guide de raccordement Voir les schémas de raccordement détaillés en fonction du type de système aux pages suivantes. Identification des bornes pour systèmes classiques : C Fil commun du côté secondaire du transformateur du système de refroidissement Rc Alimentation électrique pour le refroidissement. Raccorder au côté secondaire du transformateur du système de refroidissement. R Alimentation électrique pour le chauffage.
Français : voir la page 17 • Español: vea la página 33 Guides de raccordement en fonction du système Systèmes classiques Voir la [remarques] à la page 22 Système 1C/1F (1 transformateur) Système 1C/1F (2 transformateurs) C R Rc W Y G C R Rc W Y G Commun 24 V c.a. Alimentation [1] [R+Rc liées par un cavalier] Relais de chauffage Contacteur du compresseur ** Relais de ventilateur ** Commun 24 V c.a.
Prestige™ Installation Guide Guides de raccordement en fonction du système Thermopompes Voir les [remarques] ci-dessous Thermopompe 1C/1F [8] Thermopompe 2C/2F [10] C R Rc O/B Y G C R Rc O/B Y Y2 G Commun 24 V c.a. Alimentation [1] [R+Rc liées par un cavalier] Vanne d’inversion [7] Contacteur du compresseur ** Relais de ventilateur ** Thermopompe 2C/1F [9] C R Rc O/B Aux Y G L ** Commun 24 V c.a.
Français : voir la page 17 • Español: vea la página 33 Guides de raccordement en fonction du système Systèmes d’humidification Voir les [remarques] ci-dessous Humidificateur à vapeur (ou tout humidificateur disposant de son propre transformateur) [3, 4] Humidificateur à dérivation, à passage direct (ou tout humidificateur utilisant le transformateur du système) [3] Rc Alimentation [1] R [R+Rc reliées par un cavalier] [2] HUM1 Relais d’humidificateur [5] HUM2 Relais d’humidificateur [5] Rc Alimentation
Prestige™ Installation Guide 2 Personnalisation du thermostat (options de l’installateur) MENU Appuyer sur MENU. Appuyer sur ▼ pour faire défiler le menu vers le bas, puis appuyer sur REGLAGE PAR L'INSTALLATEUR. À l’invite du thermostat, inscrire le code de sécurité. Reglage par l'installateur Le code de sécurité correspond au code de date du thermostat (imprimé à l’arrière de la plaque murale). Ou appuyer sur MENU > ÉTAT DU MATÉRIEL pour trouver le code.
Français : voir la page 17 • Español: vea la página 33 4 Connexion des accessoires sans fil au thermostat (optionnel) MENU Appuyer sur MENU. Appuyer sur ▼ pour faire défiler le menu vers le bas, puis appuyer sur REGLAGE PAR L'INSTALLATEUR. À l’invite du thermostat, inscrire le code de sécurité. Reglage par l'installateur Le code de sécurité correspond au code de date du thermostat (imprimé à l’arrière de la plaque murale). Ou appuyer sur MENU > ÉTAT DU MATÉRIEL pour trouver le code.
Prestige™ Installation Guide Relier la télécommande au thermostat (optionnel) 1 S’assurer que le thermostat affiche la minuterie «Ajouter appareil» (voir la page 25). 2 Appuyer sur CONNECT de la télécommande. Il y a aura un court délai pendant que la télécommande recherche le signal du thermostat. 3 Lorsque l’écran affiche «Connected», appuyer sur TERMINÉ. 4 Appuyer sur non à l’écran suivant pour sauvegarder la configuration et quitter.
Français : voir la page 17 • Español: vea la página 33 5 Installation du capteur extérieur (optionnel) Installer le capteur sur un mur extérieur à la verticale, à au moins 6 pouces (15 cm) de tout surplomb. Choisir un emplacement où le capteur sera à l’abri des rayons du soleil. Fixer fermement le capteur sur le support, en mettant le dos de l’appareil contre le mur.
Prestige™ Installation Guide Tableaux de configuration par l’installateur Fonctions de configuration 100 110 112 130 140 150 160 165 172 174 176 180 190 200 210 220 230 240 250 260 281 285 300 310 320 330 342 345 346 350 360 365 366 367 368 369 371 372 374 379 380 383 (réglage de l’usine indiqué, autres options possibles) Langue Anglais Numéro de zone Aucune Nom de l’appareil Thermostat Année 2008 Mois Juin Jour 15 Options de programmation Programmable Rétablir EnergyStar Non Sélection du système Classiq
Français : voir la page 17 • Español: vea la página 33 Tableaux de configuration par l’installateur Fonctions de configuration 384 390 391 392 393 394 500 502 510 520 530 540 580 600 610 630 640 650 660 670 680 690 700 701 702 703 710 (réglage de l’usine indiqué, autres options possibles) Commande du ventilateur en déshumidification Déshumidification en mode d’absence Fonc.
Prestige™ Installation Guide Remplacement des composants du système Thermostat Après l’installation d’un nouveau thermostat, il faut réarmer tous les accessoires au nouveau thermostat, selon les directives ci-dessous.
Français : voir la page 17 • Español: vea la página 33 Caractéristiques techniques et pièces de rechange Gamme de température ambiante de service Thermostat : 0 à 48,9 °C (32 à 120 °F) Télécommande : 0 à 48,9 °C (32 à 120 °F) Capteur d’air extérieur : -40 à 60 °C (-40 à 140 °F) Humidité relative de service Thermostat : 5 % à 90 % (sans condensation) Télécommande : 5 % à 90 % (sans condensation) Capteur d’air extérieur : 0 % à 100 % (avec condensation) Encombrement (hauteur, largeur, profondeur) Thermosta
Prestige™ Installation Guide Information sur la réglementation Déclaration de conformité à la FCC (partie 15,19) (États-Unis seulement) Cet appareil est conforme à la Partie 15 des règles de la FCC. Le fonctionnement de ce système est assorti aux deux conditions suivantes : (1) L’appareil ne peut causer d’interférences nuisibles, et (2) L’appareil doit accepter les interférences reçues, y compris celles qui pourraient nuire à son fonctionnement.
Guía de instalación del sistema Termostato Prestige™ Con accesorios inalámbricos Français : voir la page 17 • Español: vea la página 33 Control para los sistemas de bombas de calor de hasta 3 etapas de calor/2 etapas de frío o para sistemas convencionales de hasta 2 etapas de calor/2 etapas de frío. Guía de instalación para: • • • Termostatos THX9000 Prestige HD y Prestige SD Control remoto inalámbrico Sensor de aire exterior inalámbrico DESCONECTE LA ENERGÍA ANTES DE COMENZAR LA INSTALACIÓN.
Prestige™ Installation Guide Instalación del sistema a simple vista Termostato Sensor de aire exterior Control remoto Equipo de HVAC Procedimiento de instalación 1 2 3 4 5 Instale y conecte el termostato................................Págs. 35-39 Personalice el termostato (configuración del instalador)..Pág. 40 Instale las baterías en los accesorios inalámbricos ......Pág. 40 Conecte los accesorios al termostato ....................Págs. 41-42 Instale el sensor exterior ................................
Français : voir la page 17 • Español: vea la página 33 1 Instale y conecte el termostato Jale del cableado a través del orificio en la placa de montaje e instale según se indica a continuación. Tarugo de pared Panel de yeso: orificio de 3/16” (4,7 mm) Yeso: orificio de 7/32” (5,5 mm) Tornillo Cableado Quite el aislante a 1/4” (6,3 mm) y conecte los cables a los terminales de los tornillos como se indica a continuación (vea las guías de cableado en las páginas siguientes).
Prestige™ Installation Guide Guía de cableado Vea las guías de cableado detalladas para los tipos de sistemas específicos en las páginas siguientes. Letras convencionales de los terminales: C Cable común procedente del lateral secundario del transformador del sistema de refrigeración. Rc Energía para la refrigeración. Conéctelo al lateral secundario del transformador del sistema de refrigeración. R Energía de calefacción. Conéctelo al lateral secundario del transformador del sistema de calefacción.
Français : voir la page 17 • Español: vea la página 33 Guías de cableado específicas del sistema Sistemas convencionales Vea [las notas] en la pág. 38.
Prestige™ Installation Guide Guías de cableado específicas del sistema Sistemas de bomba de calor Vea [las notas] a continuación.
Français : voir la page 17 • Español: vea la página 33 Guías de cableado específicas del sistema Sistemas de humidificación Vea [las notas] a continuación.
Prestige™ Installation Guide 2 Personalice el termostato (opciones del instalador) MENÚ Presione MENÚ. Presione ▼ para desplazar hacia abajo, después presione CONFIGURACIÓN DEL INSTALADOR. Ingrese el código de seguridad cuando se lo pida. Configuración del instalador El código de seguridad es el código de fecha del termostato (impreso en la parte posterior de la placa de montaje). O presione MENÚ > ESTATUS DEL EQUIPO para encontrar el código.
Français : voir la page 17 • Español: vea la página 33 4 Accesorios inalámbricos para el termostato (opcional) MENÚ Presione MENÚ. Presione ▼ para desplazar hacia abajo, después presione CONFIGURACIÓN DEL INSTALADOR. Ingrese el código de seguridad cuando se lo pida. Configuración del instalador Dispositivo inalámbrico Administrador Añadir dispositivo El código de seguridad es el código de fecha del termostato (impreso en la parte posterior de la placa de montaje).
Prestige™ Installation Guide Conecte el control remoto al termostato (opcional) CONNECT WIRELESS SETUP Presione para conectar a otro termostato YES Presione para guardar y salir NO 1 Asegúrese de que el termostato muestre el temporizador de “Añadir Dispositivo” (vea la pág. 41). 2 Presione CONNECT en el control remoto. Habrá una breve demora mientras el control remoto busca una señal procedente del termostato. 3 Cuando la pantalla muestre “Connnected”, presione DONE.
Français : voir la page 17 • Español: vea la página 33 Instale el sensor exterior (opcional) Instale el sensor en una pared exterior vertical, a 6 pulg. (15,24 cm) como mínimo, debajo de cualquier alero. Elija una ubicación donde no haya luz solar directa. Coloque bien el sensor en el soporte, orientado en dirección opuesta a la pared.
Prestige™ Installation Guide Tablas de configuración del instalador Funciones de configuración 100 110 112 130 140 150 160 165 172 174 176 180 190 200 210 220 230 240 250 260 281 285 300 310 320 330 342 345 346 350 360 365 366 367 368 369 371 372 374 379 380 383 (listado de las configuraciones de fábrica) Idioma Inglés Número de zona Sin división de zona Nombre del dispositivo Termostato Año 2008 Mes Junio Día 15 Opciones de la configuración Programable Recuperar Energy Star No Selección del sistema Conv
Français : voir la page 17 • Español: vea la página 33 Tablas de configuración del instalador Funciones de configuración 384 390 391 392 393 394 500 502 510 520 530 540 580 600 610 630 640 650 660 670 680 690 700 701 702 703 710 (listado de las configuraciones de fábrica) Control del ventilador de deshumidificación Activa el ventilador Modo de deshumidificación de casa vacante Off (desactivado) Ventilador en modo de deshumidificación de casa vacante Automático Temp.
Prestige™ Installation Guide Reemplazo de los componentes del sistema Termostato Después de instalar un termostato nuevo, se deben volver a conectar todos los accesorios al termostato nuevo, como se indica a continuación. 1 Instale y conecte el termostato nuevo (vea las pág. 35 a la 39) 2 Personalice el termostato nuevo (vea la pág. 40) 3 Conecte los accesorios inalámbricos( vea las pág.
Français : voir la page 17 • Español: vea la página 33 Especificaciones y piezas de repuesto Temperatura ambiente de funcionamiento Termostato: 32 a 120° F (0 a 48,9°C) Control remoto: 32 a 120° F (0 a 48,9°C) Sensor de aire exterior: -40 a 140° F (-40 a 60°C) Humedad relativa de funcionamiento Termostato: del 5% al 90% (sin condensación) Control remoto: del 5% al 90% (sin condensación) Sensor de aire exterior: del 0% al 100% (condensación) Dimensiones físicas (altura, ancho, profundidad) Termostato: 3-9
Prestige™ Installation Guide Información reguladora Declaración de conformidad con las regulaciones FCC (Sección 15.19) (solo en los EE. UU.) Este dispositivo cumple con la Sección 15 de las regulaciones FCC. El funcionamiento está sujeto a las dos condiciones siguientes: 1 Este dispositivo no debe causar interferencia perjudicial. 2 Este dispositivo deberá aceptar cualquier interferencia que se reciba, incluso la interferencia que pudiese causar el funcionamiento no deseado.
Need Help? For assistance with this product please visit http://customer.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 ¿Necesita ayuda? Consulte sobre este producto en http://customer.honeywell.com o llamando sin cargo a atención al cliente de Honeywell 1-800-468-1502 Vous faut-il de l’aide ? Pour obtenir de l’assistance concernant ce produit, visitez http://customer.honeywell.