Voyager™ 1400g Series Area-Imaging Scanner User’s Guide ™
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Product Agency Compliance USA FCC Part 15 Subpart B Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules.
UL Statement UL listed: UL60950-1, 2nd Edition. Canada Industry Canada ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Conformité à la règlementation canadienne Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Honeywell Scanning & Mobility Product Environmental Information Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information. Australia/NZ C-Tick Statement Conforms to AS/NZS 3548 EMC requirement Russia Gost-R certificate South Korea The product meets Korean agency approval for Class B equipment: 이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용 하는 것을 목적으로 하며 , 모든 지역에서 사용할 수 있습니다 .
Patents For patent information, please refer to www.hsmpats.com. Solids and Water Protection The Voyager 1400g has a rating of IP42, immunity of foreign particles and dripping water. Warning ! To reduce the possibility of heat-related injuries, avoid touching sections of the scanner that feel warm.
Required Safety Labels Compliance Markings information, Part Number, and Serial Number information Compliance Markings information
Table of Contents Chapter 1 - Getting Started About This Manual ...................................................... 1-1 Unpacking Your Device............................................... 1-1 Connecting the Device ................................................ 1-1 Connecting with USB ............................................ 1-1 Connecting with Keyboard Wedge ........................ 1-2 Connecting with RS232 Serial Port ....................... 1-4 Connecting with RS485.............................
Wincor Nixdorf Beetle™ Terminal Default Settings .....2-8 Keyboard Country Layout ............................................2-9 Keyboard Style ..........................................................2-15 Keyboard Conversion ................................................2-17 Control Character Output...........................................2-17 Keyboard Modifiers....................................................2-18 RS232 Baud Rate......................................................
In-Stand Sensor Mode ................................................ 3-6 Presentation Mode ...................................................... 3-7 Idle Illumination - Presentation Mode .................... 3-7 Presentation Sensitivity ......................................... 3-7 Presentation Centering.......................................... 3-8 CodeGate® .................................................................. 3-9 Mobile Phone Read Mode.........................................
Data Format Editor Commands ...................................5-4 Move Commands................................................... 5-5 Search Commands ................................................ 5-5 Miscellaneous Commands..................................... 5-6 Data Formatter.............................................................5-7 Primary/Alternate Data Formats ..................................5-8 Chapter 6 - Symbologies All Symbologies ......................................................
ISBN Translate .................................................... 6-34 EAN/JAN-8 ................................................................ 6-35 MSI ............................................................................ 6-37 GS1 DataBar Omnidirectional ................................... 6-39 GS1 DataBar Limited ................................................ 6-39 GS1 DataBar Expanded............................................ 6-40 Codablock A ................................................
Chapter 8 - Utilities To Add a Test Code I.D. Prefix to All Symbologies..............................................................8-1 Show Decoder Revision ..............................................8-1 Show Scan Driver Revision .........................................8-1 Show Software Revision..............................................8-1 Show Data Format.......................................................8-2 Test Menu....................................................................
Replacing an Interface Cable .............................. 11-2 Troubleshooting a Voyager 1400g Scanner.............. 11-2 Chapter 12 - Customer Support Appendix A - Reference Charts Symbology Charts .......................................................A-1 Linear Symbologies............................................... A-1 2D Symbologies .................................................... A-3 Postal Symbologies...............................................
viii
1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager™ 1400g area-imaging scanner. Product specifications, dimensions, warranty, and customer support information are also included. Note: The selections in this User’s Guide are dependent on the Voyager 1400g model you have purchased. PDF bar codes can only be read by models 1400gPDF or 1400g2D and cannot be read by model 1400g1D.
2. The scanner beeps. 3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The unit defaults to a USB PC Keyboard. Refer to page 2-4 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Application Note,” available at www.honeywellaidc.com.
3. Turn the terminal/computer power back on. The scanner beeps. 4. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to bar code data.
Connecting with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer. 3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 4. Once the scanner has been fully connected, power up the computer.
Connecting with RS485 A scanner or cordless base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. 2. Turn the terminal/computer power back on. The scanner beeps. 3. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. For further RS485 settings, refer to RS485, page 2-2.
Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view. The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read. Linear bar code 2D Matrix symbol The aiming beam or pattern is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit.
Setting Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before scannning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.
1-8
2 Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below.
RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It also changes the trigger mode to manual.
Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 EAN 13 UPC A UPC E 0C 16 0D 0A Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** MaxiCode 00 00 00 00 00 0A 0D 0A 18 2F 0B 0B 0B 0B 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface RS485 Packet Mode The following selection allows you to bre
USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register.
USB HID Scan the following code to program the scanner for USB HID bar code scanners. USB HID Bar Code Scanner USB Serial Scan the following code to program the scanner to emulate a regular RS232based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically uses a class driver.
Verifone® Ruby Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data format to 8 data bits, no parity bit, 1 stop bit.
Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Honeywell Bioptic Settings Datalogic™ Magellan© Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configuration.
NCR Bioptic Settings Wincor Nixdorf Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal.
Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language.
Keyboard Country (continued) Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) 2 - 10
Keyboard Country (continued) Estonia Faeroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) 2 - 11
Keyboard Country (continued) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia 2 - 12
Keyboard Country (continued) Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia 2 - 13
Keyboard Country (continued) Russian (MS) Russian (Typewriter) SCS Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) 2 - 14
Keyboard Country (continued) Switzerland (German) Tatar Turkey F Turkey Q Ukrainian United Kingdom United Stated (Dvorak right) United States (Dvorak left) United States (Dvorak) United States (International) Uzbek (Cyrillic) Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings. Default = Regular.
Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Conversion Alphabetic keyboard characters can be forced to be all upper case or all lowercase.
Default = Off. Control Character Output On * Control Character Output Off Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode.
Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode. Default = Off Turbo Mode On * Turbo Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600.
RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None.
RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the timeout. A transaction on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up.
RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the inside back cover, then scanning Save. RS232 Timeout XON/XOFF Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off).
the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off. ACK/NAK On * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Scanner-Bioptic ACK/NAK Mode Bioptic ACK/Nak On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The ScannerBioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default = Bioptic ACK/NAK Off. * Bioptic ACK/NAK Off Bioptic ACK/NAK On Scanner-Bioptic ACK/NAK Timeout This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response.
2 - 26
3 Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off Scanner * Power Up Beeper On Scanner Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.
Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper Good Read On. Beeper - Good Read Off * Beeper - Good Read On Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2400 Hz) High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz.
LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On. * LED - Good Read On LED - Good Read Off Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read.
Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = 0 ms (No Delay). * No Delay Short Delay (500 ms) Medium Delay (1,000 ms) Long Delay (1,500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
LED Illumination - Manual Trigger If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the scanner when the trigger is pressed. Default = High. Note: The LEDs are like a flash on a camera. The lower the ambient light in the room, the brighter the LEDs need to be so the scanner can “see” the bar codes.
Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LED dims until a bar code is presented to the scanner, then the LED brightens to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly. Presentation Mode Idle Illumination - Presentation Mode Scan one of the bar codes below to set the LED illumination for the scanner when it is in an idle state in Presentation Mode. Default = High.
Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read. Note: To adjust centering when the scanner is hand-held, see Centering (page 3-11). If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner.
Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right.
Mobile Phone Read Mode When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. Hand Held Scanning - Mobile Phone Presentation Scanning Mobile Phone Note: To turn off Mobil Phone Read Mode, scan the Manual Trigger Mode bar code (see page 3-5). Hands Free Time-Out The Scan Stand and Presentation Modes are referred to as “hands free” modes.
Use shorter delays in applications where repetitive bar code scanning is required. Reread Delay only works when in Presentation Mode (see page 3-7). Default = Medium. Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through the centering window, so it will not be read. 0% Bar Code 1 10 Bar Code 2 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100% Note: A bar code needs only to be touched by the centering window in order to be read.
Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save. Default Centering = 40% for Top and Left, 60% for Bottom and Right.
Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse Off bar code below is an example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes. Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video Reverse and Standard Bar Codes in order to read menu bar codes.
Working Orientation Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright. Upright: Vertical, Top to Bottom: (Rotate CW 90°) Upside Down: Vertical, Bottom to Top: (Rotate CCW 90°) Default = Upright.
3 - 16
4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), beginning on page A-4, for the prefix or suffix you wish to enter. Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 6.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix. Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Your change is automatically saved.
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-3. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
Interfunction Delay An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
you are programming. (See Primary/Alternate Data Formats on page 5-8 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 5-4) and locate the Terminal ID number for your PC. Scan three numeric bar codes on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge. Note: The wildcard for all terminal types is 099. Step 4. Code I.D.
Other Programming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page A-1), and the bar code data length for the specific data format that you want to delete. All other formats remain unaffected.
Terminal ID Table Terminal Model(s) IBM PC/AT and compatibles USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner True TTL PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Serial RS232 USB Terminal ID 003 128 129 000 000 124 125 134 131 130 Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character.
ASCII code, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-4 for decimal, hex and character codes. Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-4 for decimal, hex and character codes.
Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-4 for decimal, hex and character codes.
Default = Data Formatter On, Not Required, Keep Prefix/Suffix. * Data Formatter On, Not Required, Keep Prefix/Suffix Data Format Required, Keep Prefix/Suffix Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.
6 Symbologies This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults.
All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. All Symbologies On All Symbologies Off Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.
Codabar Codabar On/Off * On Off Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character.
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character.
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 0-48.
acter(s), it buffers Code 39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = Off. On * Off Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF.
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.
10), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly. Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80.
NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Off Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to the host computer.
which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 93 bar code that starts with a character other than a space. Default = Off. On * Off Code 93 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off On * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On/Off On * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Matrix 2 of 5 On/Off On * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Code 11 Code 11 On/Off On * Off Code 11 Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. On * Off Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Code 128 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
GS1-128 GS1-128 On/Off * On Off GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.
Telepen Telepen On/Off On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.
Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC-A UPC-A On/Off * On Off Note: When UPC-A Off is scanned, UPC-A bar codes are transmitted as EAN13.
UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 6-26. Default = Not Required. Required * Not Required UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On.
Default = Off. * Off Allow Concatenation Require Concatenation Coupon GS1 DataBar Output If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1 DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Output Off.
UPC-E0 UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 6-32). Default = On. * UPC-E0 On UPC-E0 Off UPC-E0 Expand UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.
UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Off UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
UPC-E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. To prevent transmission, scan Off. Default = On. * On Off UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 6-29). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. UPC-E1 On * UPC-E1 Off EAN/JAN-13 EAN/JAN-13 On/Off * On Off Note: If you want to convert UPC-A bar codes to EAN-13 format, scan the UPC-A Off bar code on page 6-25.
EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Off Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 6-27). ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.
EAN/JAN-8 EAN/JAN-8 On/Off * On Off EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required.
MSI MSI On/Off On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data.
GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On Off GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On Off 6 - 39
GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On Off GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
Codablock A Codablock A On/Off On * Off Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.
Codablock F Codablock F On/Off On * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Off PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On.
MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology. GS1 Composite symbologies allow for the co-existence of symbologies already in use.
GS1 Composite Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435. Minimum Message Length Maximum Message Length GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol.
Default = GS1 Emulation Off. GS1-128 Emulation GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.
QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On Off QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089.
information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = On. * On Off QR Code Page QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Off Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.
mined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = On. * On Off Data Matrix Code Page Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off On * Off MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Off Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.
ter(s), it buffers the number of Aztec bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = Off. On * Off Aztec Code Page Aztec Code pages define the mapping of character codes to characters.
Chinese Sensible (Han Xin) Code < Default All Han Xin Settings > Han Xin Code On/Off On * Off Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - Linear The following lists linear postal codes.
China Post (Hong Kong 2 of 5) On/Off On * Off China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Korea Post Korea Post On * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data.
Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D Postal Codes Off.
Planet Code On Also see Planet Code Check Digit, page 6-62. Postal-4i On Postnet On Also see Postnet Check Digit, page 6-62.
Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On Postal-4i and Intelligent Mail Bar Code On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and Intelligent Mail Bar Code On 6 - 60
Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On 6 - 61
Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.
Australian Post Interpretation This option controls what interpretation is applied to customer fields in Australian 4-State symbols. Bar Output lists the bar patterns in “0123” format. Numeric N Table causes that field to be interpreted as numeric data using the N Table. Alphanumeric C Table causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian Post Specification Tables. Combination C and N Tables causes the field to be interpreted using either the C or N Tables.
6 - 64
7 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-18 enable Control + ASCII mode.
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States [ \ ] 6 - Belgium [ < ] 6 - Scandinavia 8 < 9 6 - France ^ 8 $ 6 = Germany à + 6 - Italy \ + 6 - < ..
Supported Interface Keys ASCII HEX NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F IBM PC/AT and Compatibles, USB PC Keyboard Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Apple M
7-4
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Add Code I.D.
Show Data Format Scan the bar code below to show current data format settings. DFMBK3?. Data Format Settings Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The programming function will still occur, but in addition, the content of that programming code is output to the terminal. Note: This feature should not be used during normal scanner operation.
Scan Data Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial commands to the scanner and receive scanner response that can be seen in the Scan Data window. The data displayed in the Scan Data window can either be saved in a file or printed. Configure Configure displays the programming and configuration data of the scanner. The scanner's programming and configuration data is grouped into different categories.
Resetting the Factory Defaults ! This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the scanner to the factory default settings.
9 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS232 interface (see page 2-2). The following commands can be sent via a PC COM port using terminal emulation software.
Query Commands Several special characters can be used to query the device about its settings. ^ ? * What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a continuous range of values. A pipe (|) separates items in a list of non-continuous values.) :Name: Field Usage (Optional) This command returns the query information from the scanner.
NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters. When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.
the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value. Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings.
Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDP 1-7 Save Custom Defaults MNUCDS 1-7 Resetting the Custom Defaults Activate Custom Defaults DEFALT 1-7 Keyboard Wedge: IBM PC AT and Compatibles with CR suffix PAP_AT 2-1 Laptop Direct Connect with CR suffix PAPLTD 2-1 RS232 Serial Port PAP232 2-2 IBM Port 5B Interface PAPP5B 2-2 IBM Port 9B HHBCR-1 Interface
Selection Plug and Play Codes: USB Plug and Play Codes 9-6 Setting Serial Command # Indicates a numeric entry Page USB Keyboard (PC) PAP124 2-4 USB Keyboard (Mac) PAP125 2-4 USB Japanese Keyboard (PC) TRMUSB134 2-4 USB HID PAP131 2-5 USB Serial TRMUSB130 2-5 CTS/RTS Emulation On USBCTS1 2-5 CTS/RTS Emulation Off* USBCTS0 2-5 ACK/NAK Mode On USBACK1 2-5 ACK/NAK Mode Off* USBACK0 2-5 Verifone Ruby Terminal PAPRBY 2-6 Gilbarco Terminal PAPGLB 2-6 Honeywell Bioptic Aux Por
Selection Program Keyboard Country Setting Serial Command * Indicates default # Indicates a numeric entry Page *U.S.A.
Selection Program Keyboard Country 9-8 Setting Serial Command # Indicates a numeric entry Page Czech (Programmers) KBDCTY40 2-10 Czech (QWERTY) KBDCTY39 2-10 Czech (QWERTZ) KBDCTY38 2-10 Denmark KBDCTY8 2-10 Dutch (Netherlands) KBDCTY11 2-10 Estonia KBDCTY41 2-11 Faeroese KBDCTY83 2-11 Finland KBDCTY2 2-11 France KBDCTY3 2-11 Gaelic KBDCTY84 2-11 Germany KBDCTY4 2-11 Greek KBDCTY17 2-11 Greek (220 Latin) KBDCTY64 2-11 Greek (220) KBDCTY61 2-11 Greek (319 Latin)
Selection Program Keyboard Country Setting Serial Command # Indicates a numeric entry Page Latvia (QWERTY) KBDCTY43 2-13 Lithuania KBDCTY44 2-13 Lithuania (IBM) KBDCTY45 2-13 Macedonia KBDCTY34 2-13 Malta KBDCTY74 2-13 Mongolian (Cyrillic) KBDCTY86 2-13 Norway KBDCTY9 2-13 Poland KBDCTY20 2-13 Polish (214) KBDCTY57 2-13 Polish (Programmers) KBDCTY58 2-13 Portugal KBDCTY13 2-13 Romania KBDCTY25 2-13 Russia KBDCTY26 2-13 Russian (MS) KBDCTY67 2-14 Russian (Typewri
Selection Program Keyboard Country Keyboard Conversion Keyboard Style Control Character Output 9 - 10 Setting Serial Command # Indicates a numeric entry Page Ukrainian KBDCTY76 2-15 United Kingdom KBDCTY7 2-15 United Stated (Dvorak right) KBDCTY89 2-15 United States (Dvorak left) KBDCTY88 2-15 United States (Dvorak) KBDCTY87 2-15 United States (International) KBDCTY30 2-15 * Indicates default Uzbek (Cyrillic) KBDCTY77 2-15 *Keyboard Conversion Off KBDCNV0 2-17 Convert all Ch
Selection Keyboard Modifiers Baud Rate Setting * Indicates default Serial Command # Indicates a numeric entry Page *Control + ASCII Off KBDCAS0 2-18 DOS Mode Control + ASCII KBDCAS1 2-18 Windows Mode Control + ASCII KBDCAS2 2-18 Windows Mode Prefix/Suffix Off KBDCAS3 2-18 *Turbo Mode Off KBDTMD0 2-19 Turbo Mode On KBDTMD1 2-19 *Numeric Keypad Off KBDNPS0 2-19 Numeric Keypad On KBDNPS1 2-19 *Auto Direct Connect Off KBDADC0 2-19 Auto Direct Connect On KBDADC1 2-19 300 BPS 2
Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page 7 Data, 1 Stop, Parity Even 232WRD3 2-21 7 Data, 1 Stop, Parity None 232WRD0 2-21 7 Data, 1 Stop, Parity Odd 232WRD6 2-21 7 Data, 2 Stop, Parity Even 232WRD4 2-21 7 Data, 2 Stop, Parity None 232WRD1 2-21 7 Data, 2 Stop, Parity Odd 232WRD7 2-21 8 Data, 1 Stop, Parity Even 232WRD5 2-21 *8 Data, 1 Stop, Parity None 232WRD2 2-21 8 Data, 1 Stop, Parity Odd 232WRD8 2-21 RS232 Receiver Time-out R
Selection Scanner-Bioptic ACK/NAK Mode Scanner-Bioptic ACK/NAK Timeout Setting Serial Command # Indicates a numeric entry Page *Bioptic ACK/NAK Off 232NAK0 2-25 Bioptic ACK/NAK On 232NAK1 2-25 ACK/NAK Timeout *5100 232DLK##### 2-25 Power Up Beeper Off - Scanner BEPPWR0 3-1 *Power Up Beeper On - Scanner BEPPWR1 3-1 Beep on BEL On BELBEP1 3-1 *Beep on BEL Off BELBEP0 3-1 On BEPTRG1 3-1 *Off BEPTRG0 3-1 * Indicates default Input/Output Selections Power Up Beeper Beep on BEL Ch
Selection LED - Good Read Setting Serial Command # Indicates a numeric entry Page Off BEPLED0 3-4 *On BEPLED1 3-4 * Indicates default Number of Beeps Error *1 BEPERR3 3-4 Range 1 - 9 BEPERR# 3-4 Number of Beeps Good Read *1 BEPRPT1 3-4 Range 1 - 9 BEPRPT# 3-4 Good Read Delay *No Delay DLYGRD0 3-5 Short Delay (500 ms) DLYGRD500 3-5 Medium Delay (1000 ms) DLYGRD1000 3-5 Long Delay (1500 ms) DLYGRD1500 3-5 User-Specified Good Read Delay Range 0 - 30,000 ms DLYGRD##### 3
Selection Presentation Centering Window CodeGate Mobile Phone Read Mode Hands Free TimeOut Reread Delay User-Specified Reread Delay Setting Serial Command # Indicates a numeric entry Page Presentation Centering On PDCWIN1 3-9 *Presentation Centering Off PDCWIN0 3-9 Left of Presentation Centering Window (*40%) PDCLFT### 3-9 Right of Presentation Centering Window (*60%) PDCRGT### 3-9 Top of Presentation Centering Window (*40%) PDCTOP### 3-9 Bottom of Presentation Centering Window (*60%)
Selection Centering Window No Read Video Reverse Setting Serial Command # Indicates a numeric entry Page Centering On DECWIN1 3-13 *Centering Off DECWIN0 3-13 Left of Centering Window (*40%) DECLFT### 3-13 Right of Centering Window (*60%) DECRGT### 3-13 Top of Centering Window (*40%) DECTOP### 3-13 Bottom of Centering Window (*60%) DECBOT### 3-13 On SHWNRD1 3-13 *Off SHWNRD0 3-13 Video Reverse Only VIDREV1 3-14 Video Reverse and Standard Bar Codes VIDREV2 3-14 * Indicates
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Function Code Transmit *Enable RMVFNC0 4-4 Disable RMVFNC1 4-4 Intercharacter Delay Range 0 - 1000 (5ms increments) DLYCHR## 4-5 User Specified Intercharacter Delay Delay Length 0 - 1000 (5ms increments) DLYCRX## 4-5 Character to Trigger Delay DLY_XX## 4-5 Interfunction Delay Range 0 - 1000 (5ms increments) DLYFNC## 4-6 Intermessage Delay Range 0 - 1000 (5ms increments) DLYMSG## 4-6 DFMDF3 5-
Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page Symbologies All Symbologies Codabar Codabar Start/Stop Char. Codabar Check Char. All Symbologies Off ALLENA0 6-2 All Symbologies On ALLENA1 6-2 Default All Codabar Settings CBRDFT 6-3 Off CBRENA0 6-3 *On CBRENA1 6-3 *Don’t Transmit CBRSSX0 6-3 Transmit CBRSSX1 6-3 *No Check Char.
Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page Code 39 Message Length Minimum (0 - 48) *0 C39MIN## 6-7 Maximum (0 - 48) *48 C39MAX## 6-7 Code 39 Append *Off C39APP0 6-8 On C39APP1 6-8 *Off C39B320 6-8 On C39B321 6-8 Code 32 Pharmaceutical (PARAF) Code 39 Full ASCII Interleaved 2 of 5 *Off C39ASC0 6-9 On C39ASC1 6-9 Code 39 Code Page C39DCP 6-10 Default All Interleaved 2 of 5 Settings I25DFT 6-10 Off I25ENA0 6-10 *On I25ENA1
Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page NEC 2 of 5 Message Length Minimum (2 - 80) *4 N25MIN## 6-13 Maximum (2 - 80) *80 N25MAX## 6-13 Code 93 Default All Code 93 Settings C93DFT 6-14 Off C93ENA0 6-14 *On C93ENA1 6-16 Code 93 Message Length Minimum (0 - 80) *0 C93MIN## 6-14 Maximum (0 - 80) *80 C93MAX## 6-14 Code 93 Append On C93APP1 6-15 *Off C93APP0 6-15 Code 93 Code Page Code 93 Code Page C93DCP 6-15 Straight 2 of 5 In
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Matrix 2 of 5 Message Length Minimum (1 - 80) *4 X25MIN## 6-18 Maximum (1 - 80) *80 X25MAX## 6-18 Code 11 Default All Code 11 Settings C11DFT 6-19 *Off C11ENA0 6-19 On C11ENA1 6-19 Code 11 Check Digits Required 1 Check Digit C11CK20 6-19 *2 Check Digits C11CK21 6-19 Code 11 Message Length Minimum (1 - 80) *4 C11MIN## 6-20 Maximum (1 - 80) *80 C11MAX## 6-20 Code 128 Default All Code 128 S
Selection Telepen Setting Serial Command # Indicates a numeric entry Page Default All Telepen Settings TELDFT 6-24 *Off TELENA0 6-24 * Indicates default On TELENA1 6-24 *AIM Telepen Output TELOLD0 6-24 Original Telepen Output TELOLD1 6-24 Telepen Message Length Minimum (1 - 60) *1 TELMIN## 6-25 Maximum (1 - 60) *60 TELMAX## 6-25 UPC-A Default All UPC-A Settings UPADFT 6-25 Off UPAENA0 6-26 *On UPAENA1 6-26 Off UPACKX0 6-25 *On UPACKX1 6-26 Telepen Output UPC-A Che
Selection UPC-E0 Setting Serial Command # Indicates a numeric entry Page Default All UPC-E Settings UPEDFT 6-29 Off UPEEN00 6-29 * Indicates default *On UPEEN01 6-29 UPC-E0 Expand *Off UPEEXP0 6-29 On UPEEXP1 6-29 UPC-E0 Addenda Required Required UPEARQ1 6-30 *Not Required UPEARQ0 6-30 UPC-E0 Addenda Separator *On UPEADS1 6-30 Off UPEADS0 6-30 UPC-E0 Check Digit Off UPECKX0 6-30 *On UPECKX1 6-30 UPC-E0 Number System Off UPENSX0 6-31 *On UPENSX1 6-31 UPC-E0 Ad
Selection EAN/JAN-13 Addenda Separator ISBN Translate EAN/JAN-8 Setting Serial Command * Indicates default # Indicates a numeric entry Page Off E13ADS0 6-34 *On E13ADS1 6-34 *Off E13ISB0 6-34 On E13ISB1 6-34 Default All EAN/ JAN 8 Settings EA8DFT 6-35 Off EA8ENA0 6-35 *On EA8ENA1 6-35 EAN/JAN-8 Check Digit Off EA8CKX0 6-35 *On EA8CKX1 6-35 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 6-36 2 Digit Addenda On EA8AD21 6-36 *5 Digit Addenda Off EA8AD50 6-36 5 Digit
Selection MSI Check Character MSI Message Length GS1 DataBar Omnidirectional GS1 DataBar Limited Setting Serial Command # Indicates a numeric entry Page *Validate Type 10, but Don’t Transmit MSICHK0 6-38 Validate Type 10 and Transmit MSICHK1 6-38 Validate 2 Type 10 Chars, but Don’t Transmit MSICHK2 6-38 Validate 2 Type 10 Chars and Transmit MSICHK3 6-38 Validate Type 10 then Type 11 Char, but Don’t Transmit MSICHK4 6-38 Validate Type 10 then Type 11 Char and Transmit MSICHK5 6-38 Di
Selection GS1 DataBar Expanded Setting Serial Command # Indicates a numeric entry Page Default All GS1 DataBar Expanded Settings RSEDFT 6-40 Off RSEENA0 6-40 *On RSEENA1 6-40 * Indicates default GS1 DataBar Expanded Msg.
Selection MacroPDF417 MicroPDF417 Setting Serial Command # Indicates a numeric entry Page *On PDFMAC1 6-44 Off PDFMAC0 6-44 Default All Micro PDF417 Settings MPDDFT 6-44 On MPDENA1 6-44 * Indicates default *Off MPDENA0 6-44 MicroPDF417 Msg.
Selection Setting Serial Command # Indicates a numeric entry Page Minimum (1-7089) *1 QRCMIN#### 6-48 Maximum (1-7089) *7089 QRCMAX#### 6-48 QR Code Append *On QRCAPP1 6-49 Off QRCAPP0 6-49 QR Code Page QR Code Page (*3) QRCDCP## 6-49 Data Matrix Default All Data Matrix Settings IDMDFT 6-50 *On IDMENA1 6-50 Off IDMENA0 6-50 Minimum (1-3116) *1 IDMMIN#### 6-50 Maximum (1-3116) *3116 IDMMAX#### 6-50 *On IDMAPP1 6-51 Off IDMAPP0 6-51 Data Matrix Code Page Data Matrix
Selection Aztec Append Setting * Indicates default Serial Command # Indicates a numeric entry Page On AZTAPP1 6-54 *Off AZTAPP0 6-54 Aztec Code Page Aztec Code Page (*51) AZTDCP## 6-54 Chinese Sensible (Han Xin) Code Default All Han Xin Code Settings HX_DFT 6-55 On HX_ENA1 6-55 Chinese Sensible (Han Xin) Code Msg.
Selection Single 2D Postal Codes 9 - 30 Setting Serial Command # Indicates a numeric entry Page Australian Post On POSTAL1 6-58 British Post On POSTAL7 6-58 Canadian Post On POSTAL30 6-58 Intelligent Mail Bar Code On POSTAL10 6-58 Japanese Post On POSTAL3 6-58 KIX Post On POSTAL4 6-58 Planet Code On POSTAL5 6-59 Postal-4i On POSTAL9 6-59 Postnet On POSTAL6 6-59 Postnet with B and B’ Fields On POSTAL11 6-59 InfoMail On POSTAL2 6-59 * Indicates default
Selection Combination 2D Postal Codes Setting Serial Command # Indicates a numeric entry Page InfoMail and British Post On POSTAL8 6-59 Intelligent Mail Bar Code and Postnet with B and B’ Fields On POSTAL20 6-59 Postnet and Postal4i On POSTAL14 6-59 Postnet and Intelligent Mail Bar Code On POSTAL16 6-60 Postal-4i and Intelligent Mail Bar Code On POSTAL17 6-60 Postal-4i and Postnet with B and B’ Fields On POSTAL19 6-60 Planet and Postnet On POSTAL12 6-60 Planet and Postnet with B and
Selection Combination 2D Postal Codes (continued) Planet Code Check Digit Postnet Check Digit Australian Post Interpretation Setting Serial Command # Indicates a numeric entry Page Postnet, Postal-4i, and Intelligent Mail Bar Code On POSTAL24 6-61 Planet, Postal-4i, and Postnet with B and B’ Fields On POSTAL25 6-61 Planet, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On POSTAL26 6-61 Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On POSTAL27 6-61 Plane
Selection Setting Serial Command # Indicates a numeric entry Page Show Decoder Revision REV_DR 8-1 Show Scan Driver Revision REV_SD 8-1 Show Software Revision REVINF 8-1 Show Data Format DFMBK3? 8-2 Remove Custom Defaults DEFOVR 8-4 Activate Defaults DEFALT 8-4 Resetting the Factory Defaults * Indicates default 9 - 33
9 - 34
10 Product Specifications Voyager 1400g Scanner Product Specifications Parameter Specification Mechanical Height 1.7 inches (43mm) Length 7.1 inches (180mm) Width 2.6 inches (66mm) Weight 4.2 ounces (119g) Electrical Input Voltage 4 to 5.5VDC Operating Power 2W; 400 mA (typical) @ 5VDC Standby Power .
Parameter 6.7 mil PDF417 Specification 35 - 100mm (1.4 - 3.9 in.) 10mil Data Matrix 35 - 105mm (1.4 - 4.1 in.) 20mil QR Code 25 - 205mm (1 - 1.81 in.) Guaranteed Performance 5 mil Code 39 50 - 95mm (2 - 3.7 in.) 13 mil UPC-A 34 - 200mm (1.3 - 7.9 in.
Standard Connector Pinouts Note: The following pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
USB 10 Pin Modular Plug 1 2 3 4 5 6 7 8 9 10 Cable shield Cable select Supply ground +5V power Data + Data - RS485 Output 10 Pin RJ41 Modular Plug Note: RS485 signal conversion is performed in the cable.
11 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support on page 12-1). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Device Reading performance may degrade if the scanner’s window is not clean.
• Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing an Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the back of the scanner’s handle. This is the cable release. 4. Straighten one end of a paper clip. 5. Insert the end of the paper clip into the small hole and press in.
• You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview beginning on page 4-1 for further information. Does the scanner read the bar code incorrectly? If the scanner reads a bar code, but the data is not displayed correctly on the host screen: • The scanner may not be programmed for the appropriate terminal interface.
11 - 4
12 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below: Knowledge Base: www.hsmknowledgebase.com Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our Technical Support Portal (see below) provides an easy way to report your problem or ask your question. Technical Support Portal: www.hsmsupportportal.
This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to HII factory or authorized service center for inspection. No product will be accepted by HII without a Return Materials Authorization, which may be obtained by contacting HII.
A Reference Charts Symbology Charts Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID.
AIM Honeywell ID Possible modifiers (m) ID Hex GS1 DataBar ]em 0 y 79 GS1 DataBar Limited ]em { 7B GS1 DataBar Expanded ]em } 7D GS1-128 ]C1 I 49 ]X0 Q 51 Symbology GS1 2 of 5 China Post (Hong Kong 2 of 5) Interleaved 2 of 5 ]Im e 65 Matrix 2 of 5 ]X0 m 6D NEC 2 of 5 ]X0 Y 59 Straight 2 of 5 IATA ]Rm 0, 1, 3 f 66 f 66 0, 1 g 67 t 74 Straight 2 of 5 Industrial ]S0 MSI ]Mm Telepen ]Bm UPC 0, 1, 2, 3, 8, 9, A, B, C UPC-A ]E0 c 63 UPC-A with Add-On
2D Symbologies AIM Honeywell ID Possible modifiers (m) ID Hex Aztec Code ]zm 0-9, A-C z 7A Chinese Sensible Code (Han Xin Code) ]X0 H 48 Symbology All Symbologies 99 Codablock A ]O6 0, 1, 4, 5, 6 V 56 Codablock F ]Om 0, 1, 4, 5, 6 q 71 Code 49 ]Tm 0, 1, 2, 4 l 6C Data Matrix ]dm 0-6 w 77 GS1 ]em 0-3 y 79 GS1 Composite ]em 0-3 y 79 GS1 DataBar Omnidirectional ]em 0-3 y 79 MaxiCode ]Um 0-3 x 78 PDF417 ]Lm 0-2 r 72 ]Lm 0-5 R 52 ]Qm 0-6 s 73
AIM Symbology ID Possible modifiers (m) Honeywell ID Hex China Post ]X0 Q 51 InfoMail ]X0 , 2c Intelligent Mail Bar Code ]X0 M 4D Japanese Post ]X0 J 4A KIX (Netherlands) Post ]X0 K 4B Korea Post ]X0 ? 3F Planet Code ]X0 L 4C Postal-4i ]X0 N 4E Postnet ]X0 P 50 ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent.
Non-printable Keyboard Control + ASCII (CTRL+X) Mode ASCII control characters Windows Mode Control + X Mode On (KBDCAS2) DEC HEX Char Control + X Mode Off CTRL + X (KBDCAS0) CTRL + X function 11 0B VT Tab CTRL+ K hyperlink 12 0C FF Delete CTRL+ L list, left align 13 0D CR Enter / Ret CTRL+ M 14 0E SO Insert CTRL+ N New 15 0F SI ESC CTRL+ O Open 16 10 DLE F11 CTRL+ P Print 17 11 DC1 Home CTRL+ Q Quit 18 12 DC2 PrtScn CTRL+ R 19 13 DC3 Backspace CTRL+ S
Printable Characters (Continued) DEC HEX 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Character $ % & ' ( ) * + , .
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 † ‡ ˆ ‰ Š ‹ Œ å ç ê ë è ï î ì Ä Å É æ Æ ô ö ò û ù ÿ Ö Ü ¢ £ ¥ ₧ ƒ á í ó ú ñ Ñ ª º ¿ ⌐ ¬ ½ ¼ Home End Page Up Page Down Right ALT Right CTRL Reserved Reserved Numeric Keypad Enter Numeric Keypad / F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Numeric Keypad + Num
Extended ASCII Characters (Continued) PS2 Scan Code DEC HEX CP 1252 ASCII Alternate Extended 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 ® ¯ ° ± ² ³ ´ µ ¶ · ¸ ¹ º » ¼ ½ ¾ ¿ À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó ¡ « » ░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐ └ ┴ ┬ ├ ─ í ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧ ╨ ╤ ╥ ╙ Control Break 0x9D Alt Sequence with 1 Character 0x36 Ctrl Sequence with 1 Character 0x1D A-8 AD AE
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 Ô Õ Ö × Ø Ù Ú Û Ü Ý Þ ß à á â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù ú ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀ α ß Γ π Σ σ µ τ Φ Θ Ω δ ∞ φ ε ∩ ≡ ± ≥ ≤ ⌠ ⌡ ÷ ≈ ° · · D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA Alternate Extend
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII 251 252 253 254 255 û ü ý þ ÿ √ ⁿ ² ■ FB FC FD FE FF PS2 Scan Code Alternate Extended ISO 2022/ISO 646 Character Replacements Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Code Page Selection Method/Country Standard Keyboard Country Honeywell Code Page Option France ISO /IEC 646‐69 3 83 Germany ISO/IEC646‐21 4 84 Switzerland ISO /IEC 646‐CH 6 86 Sweden / Finland (extended Annex C) ISO/IEC 646‐11 2 82 Ireland ISO /IEC 646‐207 73 97 Danmark ISO/IEC 646‐08 8 88 Norway ISO/IEC 646‐60 9 94 Italy ISO/IEC 646‐15 5 85 Portugal ISO/IEC 646‐16 13 92 Spain ISO/IEC 646‐17 10 90 Spain ISO/IEC 646‐85 51 91 A - 11
64 91 92 93 94 96 123 124 125 126 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E US 0 1 # $ @ [ \ ] ^ ` { | } ~ CA 54 95 # $ à â ç ê î ô é ù è û CA 18 96 # $ à â ç ê É ô é ù è û JP 28 98 # $ @ [ ¥ ] ^ ` { | } ⎯ CN 92 99 # ¥ @ [ \ ] ^ ` { | } ⎯ GB 7 87 £ $ @ [ \ ] ^ ` { | } ˜ FR 3 83 £ $ à ° ç § ^ µ é ù è ¨ DE 4 84 # $ § Ä Ö Ü ^ ` ä ö ü ß CH 6 86 ù $ à é ç ê î ô ä ö ü û
Unicode Key Maps 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2B 4B 50 55 4C 51 56 2C 2E 2F 30 31 32 33 34 35 36 37 39 3D 3A 3B 3C 3E 3F 38 40 53 4F 54 59 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 104 Key U.S.
A - 14
Sample Symbols UPC-A 0 123456 7890 Code 128 Code 128 Code 39 BC321 Code 93 123456-9$ Interleaved 2 of 5 1234567890 EAN-13 9 780330 290951 Codabar A13579B Straight 2 of 5 Industrial 123456
Sample Symbols Matrix 2 of 5 GS1 DataBar 6543210 PDF417 (01)00123456789012 Car Registration Data Matrix QR Code Test Symbol Numbers 4-CB (4-State Customer Bar Code) 01,234,567094,987654321,01234567891 ID-tag (UPU 4-State) J18CUSA8E6N062315014880T
Sample Symbols Aztec Micro PDF417 Package Label MaxiCode Test Message Test Message Postnet Zip Code
Programming Chart 0 1 2 3 4 5 6 7 8 9
Programming Chart A B C D E F Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1400-UG Rev C 9/14
