HREP4, HREP8, HREP16 4-, 8-, 16-Channel Models Color Digital Video Recorder User Guide Document 800-06847 – Rev B – 08/10
User Guide
Revisions Issue Date Revisions A 05/10 New document. B 08/10 Inserted missing images in Table 2-1 and corrected the desciption of one of the buttons. Also edited the Front Panel and Rear Panel figures. Corrected the TOC to include level 1 headers. Edited the Marking Recorded Video and Archiving sections so that they are more thorough. Replaced Fig 2-21 with corrected images. Updated screen shots in Chapters 2 and 3. Added Configuring a PTZ Tour in Configuring the PTZ Setup.
HREP Color Digital Video Recorder User Guide Contents Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 About This Document . . . . . . . . . . . . . . . . . . . . . . . . Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . FCC Compliance Statement . . . . . . . . .
Contents Configuring Event/Sensor Settings. . . . . . . . Configuring Disk Management Settings . . . . . RECORD SETUP . . . . . . . . . . . . . . . . . . . . . . Configuring the Recording Behavior of your DVR Configuring Continuous/Motion Recording . . . Configuring Alarm Setup . . . . . . . . . . . . . Configuring Panic Recording . . . . . . . . . . . 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . .
HREP Color Digital Video Recorder User Guide Figures Figure 1-1 Typical System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 2-1 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 2-2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 2-3 Remote Control Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 8 Figure 2-34 SPOT OUT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 2-35 SPOT-OUT Edit Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 2-36 Spot Sequence Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Figure 2-37 Sound Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Figure 2-38 System Setup Window. . . . . . . . . . . . . . .
HREP Color Digital Video Recorder User Guide Figure 4-3 ActiveX Installation Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Figure 4-4 Internet Options Window in IE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Figure 4-5 Security Settings - Trusted Sites Zone Window . . . . . . . . . . . . . . . . . . . . . . . . 84 Figure 4-6 Live Mode in an Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 10
HREP Color Digital Video Recorder User Guide Tables Table 2-1 Front Panel Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 2-2 Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table 2-3 Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 2-4 Configurations for Continuous/Motion Recording . . . . . . . . . . . . . . . . . . . . . . .
Tables 12
HREP Color Digital Video Recorder User Guide About This Document This document introduces the HREP4-, 8-, and 16-Channel Color Digital Video recorders. It covers how to install and operate these DVRs. This document is intended for system integrators, installers, and end-user operators. Overview of Contents This document contains the following chapters and appendixes: • • • • • Chapter 1, Introduction, introduces the HREP DVR features and a typical setup.
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
HREP Color Digital Video Recorder User Guide EN55022 Class A Notice WARNING! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Important Safety Instructions • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings.
Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Operation Max temperature: 40°C USB Load condition: USB Ports(5 Vdc, Max. 500 mA) Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.
HREP Color Digital Video Recorder User Guide Font What it represents Swiss721 BT Bold Words or characters that you must type. The word “enter” is used if you must type text and then press the Enter or Return key. Italic Example Enter the password. Menu titles and other items you select Double-click Open from the File menu. Buttons you click to perform actions Click Exit to close the program.
1 Introduction Before You Install • • • • • • • • • Installation should be carried out only by qualified personnel and in accordance with any electrical regulations in force at the time. The DVR must be placed on a stable surface or mounted in an approved cabinet. Adequate ventilation must be provided, taking particular care not to block any of the air vents on the DVR. Adequate protection against lightning strikes and power surges must be installed to prevent damage to the DVR.
Introduction BACKUP: Recorded footage (including audio) can be archived to a USB memory stick or to a CD/DVD. Playback software is embedded with the backup files and the backup also contains the system event log and backup log for full traceability. REMOTE CONNECTION: Web connection allows simultaneous connection for up to four remote users per DVR. Depending on the user level, full DVR control is available over the internet as well as the ability to remotely configure the DVR.
HREP Color Digital Video Recorder User Guide Typical System Setup Figure 1-1 Document 800-06847 Rev B 08/10 Typical System Setup 21
Introduction 22
2 Installation Front Panel Description Figure 2-1 Front Panel G B A Table 2-1 C D E F Front Panel Description Group Function Description A USB Port Connect USB mouse or USB backup device B Status LED Power/Recording (including pre-recording)/Network/Alarm C POWER Turn ON/OFF the system power D Cursor Keys Allow you to navigate through the menus Increases reverse playback speed Zoom - for controlling PTZ cameras Starts reverse playback Pauses playback Parameter for PTZ cameras Start
Installation Table 2-1 Group Front Panel Description Function Description ENTER Apply or Select an item Set a PTZ camera RETURN Cancel or go to previous menu E Channel Selection Buttons Used to display individual channels in live display and playback. Also used to enter numeric passwords for the various login screens.
HREP Color Digital Video Recorder User Guide Rear Panel Description Figure 2-2 Rear Panel Example shown is the 16 channel model. The back panel layout might vary based on the model of the DVR. C C D B A Table 2-2 D E F G H I Rear Panel Description Group Name Description A CAMERA INPUTS Connect up to 4/8/16 camera inputs (depending on your model). B MONITOR Main BNC monitor. SPOT OUT BNC spot monitor. C AUDIO INPUTS/ OUTPUTS Up to 4 audio inputs and one audio output can be connected.
Installation Remote Control Figure 2-3 Remote Control Description SETUP Open System Setup menu POWER System power On/Off Channel selection buttons AUDIO Not supported ID button Select DVR ID RETURN Cancel/Deselect Previous screen ENTER Apply/Select/Go to next screen Navigation Buttons Used for playback control, menu navigation, and PTZ/focus control DISP Change the display screen SEARCH Go to Search mode PTZ Go to PTZ menu PANIC Start panic recording KEYLOCK Lock the Remote/Front keys SEQUENCE Chang
HREP Color Digital Video Recorder User Guide Setting the DVR ID Using the Remote Control 1. Press the ID button on the remote control. An Input ID message displays. 2. Press the Set ID, then press RETURN. Returning to the Original ID Settings 1. Press the ID button again. 2. Enter 255, then press the RETURN button on the remote control.
Installation Figure 2-4 Startup Screen The DVR startup screen detects and checks the status of the hard drives and the CDRW/DVD-RW drive. Logging On After startup diagnostics are complete, you must log onto the system. The default user name is ADMIN. Figure 2-5 Log On Screen Enter the default password 1234 using the channel selection buttons, then press ENTER. The DVR begins normal operation and shows the default display of 4, 8, or 16 channels (depending on your DVR model).
HREP Color Digital Video Recorder User Guide Figure 2-6 Default Display Navigating the Default Display The control bar at the bottom of the screen when the DVR is first turned on. After that, it will show the current time and date. Each channel has a title. The red square and letter 'C' in the top right corner of each channel display indicates that the channel is in Continuous recording mode.
Installation Live Display Configuring the Screen Division 1. Navigate to DISPLAY in the Control bar, then click The Display popup menu appears. Figure 2-8 2. . Display Popup Menu Select the screen division (1, 4, 6, 8, 9, 16, or a rotation sequence) from the popup menu. Sequencing the Channels Click SEQ in the display popup menu. Each channel is shown in full screen for a set period of time before switching to the next channel in the sequence.
HREP Color Digital Video Recorder User Guide Figure 2-9 PTZ Window Select the camera channel 2. Select the camera by channel. 3. Use the arrow buttons to reposition the PTZ camera field of view. 4. Use ZOOM, FOCUS, and IRIS to change the current camera view. 5. Click PARAMETER to configure PTZ camera parameters. See Table 2-1 on page 23 for descriptions of front panel and remote controller controls for PTZ cameras.
Installation Viewing the Log Navigate to LOG in the control bar, then click A LOG window appears. Figure 2-11 to see the current log. Log Window Select a log entry to view the associated video. Panic Recording Navigate to REC in the control bar, then click to start and stop Panic recording. The REC button changes to a red square with a “P” to indicate that panic recording has started. Use the RECORD SETUP window to configure the Panic recording settings. See Configuring Panic Recording on page 70.
HREP Color Digital Video Recorder User Guide Figure 2-12 Note Quick Menu You cannot access the Quick Menu if you are in a Display Sequence. Table 2-3 Quick Menu Function Description FREEZE ON/OFF Stop or freeze the live display of your selected channel on your HREP8 or HREP16; stop or freeze all channels on your HREP4. Even though other channels show live display, this particular channel display is stopped. Right-click and then select FREEZE OFF to exit the freeze mode.
Installation System Setup Navigate to MENU on the control panel, then click The SETUP window appears. Figure 2-13 . SETUP Window Click SYSTEM SETUP in the SETUP window. The MAIN menu window appears. Figure 2-14 MAIN Menu Window Use the cursor keys and menu. (ENTER) and (RETURN) to navigate the MAIN setup Use to select and change a particular item. Use particular setup screen. Select SYSTEM SETUP and then press to cancel a change or exit from a to set up all the main system functions.
HREP Color Digital Video Recorder User Guide Figure 2-15 Camera Setup Window Highlight the camera you want to configure, then press following: • • • . You can configure the TITLE: Enter the camera title (maximum 8 characters) COVERT: When COVERT is turned ON, the camera image is not displayed in Live display, but the DVR continues to record the video. When COVERT is turned ON and a Manager or User account is logged on, the live channel does not display in the Web Client display.
Installation Figure 2-16 COLOR SETUP Menu You can adjust the brightness, contrast, tint, and color for each channel. Select a channel and click to select that channel for configuration. The selected channel displays full screen. Figure 2-17 Example of Configuring the Color Setup Window Click the Up/Down arrows Click 36 to configure the brightness, contrast, tint, and color. when all changes are complete and you want to escape this window.
HREP Color Digital Video Recorder User Guide Configuring the PTZ Setup Click PTZ on the left side of the CAMERA window. The PTZ Setup menu appears. Figure 2-18 PTZ SETUP Menu Click each value in the ADDRESS, PROTOCOL, and BAUD RATE columns to configure them. Use the to change the following values: ADDRESS The unique ID of the PTZ device PROTOCOL The protocol of the PTZ device BAUD RATE The baud rate of the PTZ device DETAIL Detailed settings for the PTZ device.
Installation Use the Note to change the values, then click OK to save the settings. Some settings such as AUTO FOCUS might not be compatible with your particular PTZ equipment. If this is the case, then changing the value will not have an effect on the PTZ control. Configuring PTZ Presets in Live View Configure PTZ presets for a preset tour. See Configuring a PTZ Tour on page 39. 1. Navigate to PTZ appears. Figure 2-20 in the Control bar, then click to select.
HREP Color Digital Video Recorder User Guide Figure 2-21 PTZ Parameter Window Configuring a PTZ Tour You can configure a PTZ tour for each PTZ camera that is connected to the HREP. Before you can con figure a PTZ tour, you must configure the presets. See Configuring PTZ Presets in Live View on page 38. 1. Click TOUR on the PTZ SETUP menu (see Figure 2-18). The PTZ TOUR window appears. Figure 2-22 PTZ TOUR Window 2. Click next to MODE to select AUTO to enable PTZ Tour setup. 3.
Installation Figure 2-23 Motion Sensor Menu Use the to change the sensitivity level. The lowest level is 1, and the highest is 10. This setting determines the degree of motion required before recording is activated. Configuring the Motion Sensor Area Click the AREA SETUP button next to your desired channel. A grid appears over the video image for the chosen channel.
HREP Color Digital Video Recorder User Guide Figure 2-25 DISPLAY Window Configuring the On-Screen Display (OSD) If it isn’t already selected, click OSD on the left side of the DISPLAY window. See Figure 2-25. Use the to change the following values: STATUS BAR Choose how long the control bar displays before it disappears and the date/time displays. CAMERA TITLE Enable/disable the display of the camera title.
Installation Figure 2-26 Use the DISPLAY MONITOR Menu to change the following values: SEQUENCE DWELL Choose how long each screen is displayed in a sequence. SPOT DWELL Choose how long each screen is displayed on the spot monitor outputs. DE-INTERLACED MODE Set to ON when recording any channels in D1 resolution (704x576) to prevent shudder during playback. ALARM POP-UP MODE Set to ON so that the associated channel displays in full screen when an alarm is triggered.
HREP Color Digital Video Recorder User Guide Figure 2-27 SEQUENCE Menu When the SEQ button is pressed, the default sequence cycles through all 16 channels, one by one. Sequence setup allows you to define a custom sequence, using mixed multi screen views and any desired channels. Adding a Sequence 1. Click ADD at the bottom of the SEQUENCE menu. The Add window appears. Figure 2-28 Add Sequence Window 2. Click to bring up the virtual keyboard to change the Sequence Title from DEFAULT.
Installation Figure 2-29 5. Click ADD. The SEQUENCE SETUP window appears. Figure 2-30 6. Sequence Window SEQUENCE SETUP Window Select a screen display layout from the VIEW TYPE, select the channels for the layout from the CONFIGURE panel, then click CONFIRM. Click ADD to add another mode. Double-click the current sequence to modify it. The SEQUENCE SETUP window reappears. Click CLOSE when you are finished. Activating a Sequence Press SEQ on the front panel or select Sequence view.
HREP Color Digital Video Recorder User Guide Figure 2-31 2. Sequence EDIT Window Click MODIFY. The Sequence window opens. Figure 2-32 Sequence Window 3. Right-click on a step in the sequence, then choose to modify it, to delete it, or to cancel this action. 4. Make the changes, then click CONFIRM. Click CLOSE to close that sequence. Deleting a Sequence 1. Double-click in the List column the sequence you want to delete. The EDIT window appears. Figure 2-33 2. Sequence EDIT Window Click DELETE.
Installation Figure 2-34 2. Click the camera channel to turn the monitor ON/OFF. 3. Double-click the spot-out channel that you want to assign. The Edit window appears. Figure 2-35 46 SPOT OUT Menu SPOT-OUT Edit Window 4. Click to bring up the virtual keyboard to change the Spot Title from DEFAULT. Use the virtual keyboard to enter a name or reference number for the new sequence. 5. Turn the SCHEDULE ON or OFF. 6. Click MODIFY, then double-click the current display to modify it.
HREP Color Digital Video Recorder User Guide Figure 2-36 8. Spot Sequence Setup Window Select a screen display layout from the VIEW TYPE, select the channels for the layout from the CONFIGURE panel, then click CONFIRM. Note You can choose from Single or Quad display only. Click ADD to add another mode. Double-click the current sequence to modify it. The SEQUENCE SETUP window appears. Click CLOSE when you are finished. The new sequence is now saved and can be started by pressing SEQ when in live view.
Installation Configuring Audio Settings 1. Click AUDIO on the left side of the SOUND window. 2. Use the to configure the following settings: LIVE AUDIO When ON, the selected audio channel can be monitored on the AUDIO OUTPUT. DEFAULT AUDIO CHANNEL Specify which one of the four AUDIO INPUTS is routed to the AUDIO OUTPUT. NETWORK AUDIO TX When ON, live audio is transmitted to a remote PC connection. Recorded audio is transmitted with video to a remote PC for playback.
HREP Color Digital Video Recorder User Guide Configuring the System Date/Time 1. Click DATE/TIME on the left side of the SYSTEM window. 2. Use the to configure the following settings: DATE & TIME Set the current date and time DATE FORMAT Determine how the date is displayed. TIME FORMAT Determine how the time is displayed. NETWORK TIME SERVER If the DVR is connected to the internet, the time and date can be accurately set by selecting SYNC and pressing .
Installation The SYSTEM INFORMATION Window displays the following information: F/W Version Shows the firmware version of the DVR. H/W Version Shows the hardware version of the DVR. Video Signal Type PAL or NTSC according to the DIP switch setting on the rear panel of the DVR. See Table 2-2 on page 25. Disk Capacity The first value shows the amount of hard drive capacity used by recorded footage. The second value shows the total hard drive capacity installed.
HREP Color Digital Video Recorder User Guide 4. Select the firmware from the firmware list, then click UPGRADE. The firmware upgrade begins. FACTORY DEFAULT Use to restore factory default settings. SYSTEM DATA System settings can be saved to a USB memory stick. The settings can be reloaded in case of accidental factory default or can be transferred to another DVR if multiple units need to be installed with the same settings. All information is saved apart from the network settings and the system name.
Installation Figure 2-43 USER Setup Window By default, the DVR is configured with a user ID of ADMIN, belonging to the ADMIN group and with a password of 1234. You can add up to seven new users (for a total of eight) and edit existing user details. Modifying User Details 1. Highlight the user with the green cursor, press The Edit window appears. Figure 2-44 2. 52 .
HREP Color Digital Video Recorder User Guide 3. GROUP Assign the user to one of three groups: ADMIN, MANAGER, or USER. E-MAIL Enter the user’s e-mail address (up to 64 characters) if e-mail notification is required. E-MAIL NOTIFICATION Enable or disable e-mail notifications for the specified user. Click OK to save the settings. Adding a New User 1. Click ADD in the USER Setup window. The Add window appears. Figure 2-45 2. 3.
Installation Figure 2-46 USER AUTHORITY Menu Select and click to change the authority for the Manager and Users. Click APPLY after selecting each item. Note Any user can be deleted except the default ADMIN user. User authority is effective only when the PASSWORD is ON in the System Management Settings. See Configuring System Management Settings on page 49. Configuring User Log Out 1. Click LOG OUT on the left side of the USER window. The LOG OUT menu appears. Figure 2-47 2.
HREP Color Digital Video Recorder User Guide Configuring Network IP Settings Figure 2-48 IP NETWORK Setup Window Click the IP SETUP menu tab if it isn’t already selected, then configure the following: Document 800-06847 Rev B 08/10 DHCP When enabled, the DVR will obtain an IP address automatically if it is connected to a DHCP server or router. IP ADDRESS If DHCP is not being used, then the IP address can be manually set.
Installation RTSP SERVICE PORT If connected, then the router supports UPNP (Universal plug and play) function. When you click the AUTO PORT, the port forwarding is automatically set up. You can also delete a port and test a port’s functionality from here. WEB SERVER PORT If connected, then the router supports UPNP (Universal plug and play) function. When you click the AUTO PORT, the port forwarding is automatically set up. You can also delete a port from here.
HREP Color Digital Video Recorder User Guide Caution To use the DDNS function, you need to set up port forwarding: a. Default WEB SERVICE PORT: 8080 b. Default RTSP SERVICE PORT: 554 The default DDNS HOST NAME is your Mac address. You can connect in one of two ways: (Mac address/Host name) 00115ff00213.dvrlink.net 1234.dvrlink.net (You can enter any DDNS Host name.) Configuring for E-mail Notifications 1. Click E-MAIL on the left side of the NETWORK window. The E-MAIL setup menu appears. Figure 2-50 2.
Installation Configuring Event/Sensor Settings Select EVENT/SENSOR in the Main system setup window, then click EVENT/SENSOR setup window opens. Figure 2-51 . The EVENT/SENSOR Setup Window Configuring for HDD Events 1. Click HDD EVENT on the left side of the EVENT/SENSOR window if it is not already selected. The HDD EVENT setup menu appears. See Figure 2-51. 2. Configure the DVR to monitor the hard drives and detect problems: S.M.A.R.T. HDD ALARM Enables S.M.A.R.T. disk monitoring.
HREP Color Digital Video Recorder User Guide Figure 2-52 2. ALARM INPUT Setup Menu Click OPERATION and TYPE to edit those settings to determine the behavior of each of the alarm inputs: OPERATION Enable/disable alarm inputs. TYPE Set alarm inputs to N/O (normally open) or N/C (normally closed). Configuring Alarm Output 1. Click ALARM OUTPUT on the left side of the EVENT/SENSOR window. The ALARM OUTPUT setup menu appears.
Installation 2. 3. Configure the following behavior settings: ALARM OUT Choose to configure a specific alarm output. OPERATION Enable/disable the selected alarm output. MODE Select from TRANSPARENT (the output is active only when the trigger criteria are present) or LATCHED (the output is active for a set period of time after a trigger). DURATION In LATCHED mode, this is the time that the alarm output remains active after it has been triggered.
HREP Color Digital Video Recorder User Guide Figure 2-54 BUZZER OUT Setup Menu These settings determine the behavior and actions that will trigger the internal buzzer. 2. 3. Configure the following behavior settings: OPERATION Enable/disable the internal buzzer. HDD EVENT Determines whether a hard drive event triggers the buzzer. MODE Select from TRANSPARENT (the buzzer sounds only when the trigger criteria are present) or LATCHED (the buzzer sounds for a set period of time after a trigger).
Installation Figure 2-55 E-MAIL NOTIFICATION Setup Menu These settings determine the behaviors and actions that will send an e-mail to a remote user. 2. 3. Configure the behavior settings: NOTIFICATION Turn ON/OFF e-mail notification. SETUP CHANGE Configure whether a setup change triggers an e-mail notification. HDD EVENT Configure whether a hard drive event triggers an e-mail notification. BOOTING EVENT Configure whether a booting event triggers an e-mail notification.
HREP Color Digital Video Recorder User Guide Configuring Disk Management Settings Select DISK MANAGEMENT in the Main system setup window, then click MANAGEMENT setup window opens. Figure 2-56 . The DISK DISK MANAGEMENT Setup Window Highlight DISK MANAGEMENT, then press RECORD TIME LIMIT to manage the internal hard drives. In certain circumstances, it might be necessary to limit the amount of footage stored on the DVR (to comply with data protection laws for example).
Installation RECORD SETUP Click MENU on the control panel. The SETUP window appears. Figure 2-57 SETUP Window Click RECORD SETUP in the SETUP window. The RECORDING window appears. Figure 2-58 RECORDING Setup Window Configuring the Recording Behavior of your DVR Use the to configure the settings on the RECORDING OPERATION window. See Figure 2-58. 64 SCHEDULE MODE Select either DAILY (one schedule applies to every day of the week) or WEEKLY (each day of the week has its own schedule).
HREP Color Digital Video Recorder User Guide Configuring Continuous/Motion Recording 1. Click CONTINUOUS/MOTION RECORDING on the left side of the RECORDING setup window. The CONTINUOUS/MOTION RECORDING Setup window opens. 2. Press to choose this window. Figure 2-59 3. CONTINUOUS/MOTION RECORDING Setup Window Use this window to configure scheduled and motion detection settings.
Installation Figure 2-60 Configuring SIZE/FPS/QUALITY Time Bar Each green cursor box represents one hour. The table below the time bar shows the recording settings for this time period. 2. Select a length of time on the schedule. A new configuration window opens.
HREP Color Digital Video Recorder User Guide 3. Configure the SIZE, FPS, QUALITY, and AUDIO for each channel. Click setting. Click to cancel a setting and exit that setting. Table 2-4 to save a Configurations for Continuous/Motion Recording Configuration Description SIZE Select recording resolutions of 352x240, 704x240, or 704x460 (NTSC) can be selected for each channel. FPS Frame rates between 1 and 30 can be set for each channel.
Installation Configuring the Schedule 1. Use the cursor keys to navigate to SCHEDULE, then press Figure 2-62 Configuring the Schedule 2. To change the SCHEDULE settings, press The schedule box highlights in green. 3. Press and hold , then use the cursor keys to drag and select the recording time and the channels. Figure 2-63 4. 68 . again. Selected Channels and Time Click again when you have made your selection. The EVENT window opens.
HREP Color Digital Video Recorder User Guide Figure 2-64 5. EVENT Window Select the type of event recording (NONE, CONTINUOUS, MOTION, CONTINUOUS/MOTION), then click OK. The EVENT window closes. Color Codes for the Schedule Screen The schedule screen uses four differently colored blocks to indicate the different recording modes. Table 2-5 Color Codes for the Recording Modes Block Color Recording Mode PINK No scheduled or motion recording. SKY BLUE Continuous recording.
Installation Note Alarm-activated recording can be used in conjunction with Continuous/Motion Recording. For example, you can configure your DVR to record continuously at a low frame rate (set in Continuous/Motion Recording), and then to increase to a higher frame rate during an alarm input (set in ALARM SETUP). Configuring Panic Recording Click PANIC RECORDING on the left side of the RECORDING setup window. The PANIC RECORDING Setup window opens.
3 DVR Operation Searching for Video Use the SEARCH function to search for a particular section of recorded footage. To prevent unauthorized viewing of footage, only users with ADMIN or MANAGER user levels can play back footage. Searching for Video 1. Log on as ADMIN. See Logging On on page 28. 2. Navigate to SEARCH on the control panel, then click The SEARCH window appears. Figure 3-1 Calendar Document 800-06847 Rev B 08/10 .
DVR Operation The DVR uses a calendar and timeline search method for quick access to recorded footage. The calendar displayed on the left in Figure 3-1 shows the current month. Days highlighted in blue have recorded footage. The timeline on the right shows a 24-hour status of all channels for the selected day. The recorded time displays with a different color for each recording type.
HREP Color Digital Video Recorder User Guide Figure 3-2 PANO Playback Window Each channel screen contains a 3-hour segment of recorded data. Channel Time frame CH1 00:00 - 03:00 CH2 03:00 - 06:00 CH3 06:00 - 09:00 CH4 09:00 - 12:00 CH5 12:00 - 15:00 CH6 15:00 - 18:00 CH7 18:00 - 21:00 CH8 21:00 - 24:00 Select a channel, and you can play back the recorded video at a speed of up to 64x. See Changing the Playback Speed on page 74 for more information.
DVR Operation Figure 3-3 Playback Window This is the Multi View PLAY mode. The default playback mode is a 16-screen display. Figure 3-4 Playback Controls DISPLAY button Switching to Viewing a Single Channel Press DISPLAY (See Figure 3-4) or use the CHANNEL SELECTION buttons on the front panel or the remote control to select a channel for displaying on a single screen, or to choose other multi screen formats.
HREP Color Digital Video Recorder User Guide Marking Recorded Video During Playback for Archiving During playback, you can reserve recorded data that you want to archive. 1. Click at the point in the recorded video when you want to start archiving. Video playback stops and the INFORMATION window appears. Figure 3-5 INFORMATION Window 2. Enter a TAG name, then click START. The display returns to playback format and playing recorded video. 3. Click at the point at which you want archiving to end.
DVR Operation Exiting Playback Mode To exit the playback mode and return to the Search window (see Figure 3-1), press To exit the Search window and return to Live View, press . again. Searching for Events The DVR event log stores events such as motion- and alarm-activated recording, and video loss. 1. Log on as ADMIN. See Logging On on page 28. 2. Navigate to SEARCH on the control panel, then click The SEARCH window appears. Figure 3-6 3.
HREP Color Digital Video Recorder User Guide Figure 3-7 SEARCH BY EVENT Window Search button Search log 4. Select a channel and a condition, and then use 5. Click SEARCH to begin the search. to change the settings. Playing Event Footage Use the cursor keys to navigate the search log (see Figure 3-7), then click event. The playback window appears. Figure 3-8 to select an Playback Window Playback begins with the time of the selected event, and continues until you stop playback.
DVR Operation To stop playback and return to Live View, press repeatedly. Archiving Data Administrators can archive data to a USB memory stick or a CD/DVD. To protect unauthorized viewing and distribution of footage, only users with ADMIN level of authority (see Configuring User Authority on page 51) can archive data. Using NEW ARCHIVING to Archive Data 1. Press BACKUP on the front panel or use a mouse click ARCH on the control bar. The ARCHIVING window appears. Figure 3-9 2.
HREP Color Digital Video Recorder User Guide 3. Enter a TAG name in the TAG field. 4. Click RESERVE or BURN. The BURNING window appears after you click BURN. Figure 3-10 5. BURNING Window Select a DEVICE and a BURNING TYPE, then click START in the BURNING menu. Using RESERVED DATA MANAGEMENT to See Archived Data 1. Press BACKUP on the front panel or use a mouse click ARCH on the control bar. The ARCHIVING window appears. See Figure 3-9. 2.
DVR Operation The AVI ARCHIVING LIST displays the AVI archiving data that was reserved from the NEW ARCHIVING menu or archived during a search/playback session. See Marking Recorded Video During Playback for Archiving on page 75. Table 3-2 AVI ARCHIVING LIST Functions Button Function INFORMATION View the detailed information of reserved AVI data. DELETE Delete the reserved AVI data. BURN Backup the selected AVI data. Select a clip by name in the AVI ARCHIVE LIST, then click BURN. 3.
4 Using the Web Remote Viewer Preparing for an Internet Connection Port Forwarding For an internet connection, you should set ports 554 and 8080 in your Router for port forwarding. Refer to your Router manual for port forwarding settings. Minimum Internet Requirements Table 4-1 Document 800-06847 Rev B 08/10 Internet RA Minimum PC Requirements CPU P4 3.0 or higher RAM 512MB or higher VGA • • VGA Memory 64MB Monitor 1280x1024 OS Microsoft® Windows® XP2 IE Version IE6.
Using the Web Remote Viewer Connecting to the Internet 1. Open IE. 2. Enter the IP Address or the URL of your DVR into the IE Explorer Address bar. When using the DDNS services, enter the URL as shown below: • • http://1234.dvrlink.net:8080 (webport:8080), or http://1234.dvrlink.net (webport:80) The Windows Security window opens. Figure 4-1 3. 82 Entering the User Name and Password for Internet Connection Enter the Default ID (ADMIN) and password (1234), then click OK.
HREP Color Digital Video Recorder User Guide Figure 4-2 4. Select Run Add on to install ActiveX. An ActiveX Installation window opens. Figure 4-3 5. ATM-Windows Internet Explorer Add-on Option Window ActiveX Installation Window Click Install to install ActiveX. Enabling the Installation of ActiveX You might not be able to install ActiveX due to some Internet Explorer security settings. To change these security settings, go to Tools > Internet Options > Security > Custom Level.
Using the Web Remote Viewer Figure 4-4 6. Click Custom level.... The Security Settings - Trusted Sites Zone window appears. Figure 4-5 7. 84 Internet Options Window in IE Security Settings - Trusted Sites Zone Window Select Enable for all ActiveX-related options, then click OK to save the changes.
HREP Color Digital Video Recorder User Guide Live Mode Figure 4-6 Live Mode in an Internet Connection Table 4-2 Live Mode Functions Live Mode Function Description Select the division of the screen in Live view mode. Select from 1, 4, 8, 9, and 16 screens. • • • Move to next N cameras, for example from ch1-4 to ch5-8 in 2x2 view Move to the next camera Display Full Screen Manually select the live channel. Document 800-06847 Rev B 08/10 • • Activate Mic to send sound to the DVR.
Using the Web Remote Viewer Table 4-2 Live Mode Functions Live Mode Function Description Status Shows the active status of the DVR: Alarm - Indicates an Alarm input. Motion - Indicates detected Motion. Video Loss - Indicates when a Video Loss alarm is detected. Recording - Indicates the current recording mode (T=Continuous; M=Motion; A=Alarm recording) Alarm Out - Indicates when an Alarm Output is detected. Refresh Time - Set the interval of Refresh for the camera status and log.
HREP Color Digital Video Recorder User Guide Searching for Recorded Video Searching by Timeline 1. Click Search in the Live mode window. The Search window appears. Figure 4-7 Internet Search Window In this window, you can do the following functions: 2. Document 800-06847 Rev B 08/10 Function Description Refresh Refresh the data in the recording table. Play Play the data recorded from the system.
Using the Web Remote Viewer Figure 4-8 Searching By Timeline 3. Select a timeline on the timetable, or set an exact time, then click Play. 4. Click Backup, and the Backup configuration window opens. Figure 4-9 Backup Configuration Window Searching by Event 1. Click Search By Event. The Search By Event window opens. Figure 4-10 2. 88 Search By Event Window Select the type(s) of event(s) you want to search.
HREP Color Digital Video Recorder User Guide 3. Configure a time frame for the search in the From and To fields for the Time Period, then click Search. The results of the search display. Figure 4-11 Event Search Query Results Setup Mode In the Setup window, in the field on the left, you can access configuration menus for configuring: • • • • • • • • Cameras The display Sound parameters System setup Recording parameters Users The network connection Sensors Click Setup in the Live mode window.
Using the Web Remote Viewer Figure 4-12 Internet Connection Camera Setup Window Using an Internet Connection to Configure a Camera You can configure a camera’s title, live color display, PTZ setup, and motion detection settings. 1. Click Camera again under Camera in the field on the left. Figure 4-12 appears. 2. Make your configuration selections, and then click Ok to save. Configuring Motion Detection 1. 90 Click Motion under Camera. The Motion Setting window opens.
HREP Color Digital Video Recorder User Guide Figure 4-13 Motion Setting Configuration Window 2. Select a channel and a sensitivity level. 3. Drag your mouse on the image to select a detection area. 4. Click OK. See Configuring PTZ Camera Parameters on page 31 for more information. Configuring the On-Screen Display You can choose which text items display over the image. Click OSD under Display in the field on the left. The OSD Setting window opens.
Using the Web Remote Viewer See Configuring the Display on page 39 for more information about configuring the display. Configuring the Monitor Click Monitor under Display in the field on the left. The Monitor Setting window opens. Figure 4-15 Monitor Setting You can set the dwell time for a sequence or spot, and for the pop-up functions. See Configuring the Monitor Display on page 40 for more information. Configuring the Sound Settings Click Audio/Buzzer under Sound in the field on the left.
HREP Color Digital Video Recorder User Guide Audio Setting Enable/disable Audio and select a default audio channel. Buzzer Setting Enable/disable the buzzer for event notification. See Configuring Sound Settings on page 45 for more information. Configuring the System Setup Click System in the field on the left. The Date/Time Setting window opens.
Using the Web Remote Viewer Figure 4-18 Continuous/Motion Recording Setting Window You can configure the recording settings. Configuring recording settings is similar to configuring system settings. See Configuring the Users on page 49 for more information. Configuring Users Click User in the field on the left. The User Authority Setting window opens. Figure 4-19 User Authority Setting Window You can add a user, select a user’s authority level, and configure the user’s log-out time.
HREP Color Digital Video Recorder User Guide Configuring the Network Click Network under Network in the field on the left. The IP Setup Setting window opens. Figure 4-20 IP Setup Setting Window You can check the system’s network information and selectable speed level. You cannot change IP settings. The network IP can be set only on the DVR. See Configuring the Network Settings on page 52 for more information. Configuring E-mail Notification Click E-mail under Network in the field on the left.
Using the Web Remote Viewer Configuring Sensors Click Sensor under Sensor in the field on the left. The Alarm Output Setting window appears. Figure 4-22 Alarm Output Setting Window Users with ADMIN privileges can set all device options for Alarm in/out and buzzer out for event notification (HDD event, alarm input, alarm output, buzzer out, and e-mail notification). See Configuring Alarm Setup on page 67 for more information.
HREP Color Digital Video Recorder User Guide Figure 4-23 Document 800-06847 Rev B 08/10 Information About Your DVR 97
Using the Web Remote Viewer 98
5 Watermark Process This process applies to video clips that were burned to CD/DVD or to USB media using the Backup/Archive/Burn process from the front panel of the DVR. 1. Open the backup data from the device and then run the [bplayer] which is included in the backup folder. Figure 5-1 2. Document 800-06847 Rev B 08/10 bplayer Click the [Open file] button and open the backup file.
Watermark Process Figure 5-2 3. Click Yes when the Checking the watermark? message appears after opening the backup file.
HREP Color Digital Video Recorder User Guide The file opens. Note Document 800-06847 Rev B 08/10 If the backed-up AVI file has been modified, a Verification Failed message appears.
Watermark Process 102
Honeywell Systems Group (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywellvideo.com +1.800.796.2288 Honeywell Systems Group Northern Europe Ampèrestraat 41 1446 TR Purmerend, The Netherlands www.honeywell.com/security/nl +31.299.410.200 Honeywell Systems Group Europe/South Africa Aston Fields Road, Whitehouse Industrial Estate Runcorn, Cheshire, WA7 3DL, UK www.honeywell.com/security/uk +44.01928.
