IH25 UHF RFID Reader Quick Start Guide IH25-EN-QSG REV A
Introduction The IH25 UHF RFID Reader provides Ultra High Frequency (UHF) Radio Frequency Identification (RFID) connected to a mobile terminal. The unit can read and write to bar code, QR code and UHF RFID tags.
Battery Installation and Remove Install the battery before using the reader for the first time. 1. To access the battery compartment, remove the battery cover screws and then the battery cover. 2. Insert the battery into the battery compartment with the tape at the bottom. 3. Attach the battery cover and tighten the screws. Note that the torque should be 3.5kg.f. MODE 2 1 3.8V 4000 mAh Tape To uninstall the battery, remove the battery cover screws and then the battery cover.
Charging Before using the reader for the first time, ensure the battery is fully charged. To charge the reader, use the USB cable, the USB cable + AC charge adapter or a docking station.
Docking Station Charge Use the one slot or four-slot docking station to charge IH25 and the mobile terminal. Note: when charging, make sure the charging indicator is always on.
Fitting Device Case and Attaching Device 1. Insert the mobile terminal into the case and press it down. Note: When installing the bracket, pay attention to the angle and strength so as not to damage the product. 2 1 2. Turn on power to the reader and the mobile terminal. Use the mobile terminal to scan the QR code on the label attached at the bottom of the reader’s main body.
3. Check the stud on the bottom of the case and the socket on the reader are clean and free from dirt or debris. 4. Align the stud with the socket, ensuring that it is parallel, and press the two parts together firmly until they click into place.
Reading RFID Tags 1. Turn on power to the reader and it beeps one time. 2. Press and hold the MODE button for at least 3 seconds to switch to RFID mode. The RFID indicator is on and then off after 5 seconds. 3. Press the trigger button to read tags. RFID tags can be read when they are in range. The range (typical 0.2ft—20ft) at which a tag can be read depends on the tag type and size and the number of tags in the field.
MODE Button and Status Indicators MODE MODE MODE Press the MODE button to light on the current mode light. Release the button within 3 seconds, the mode light is off. Press and hold the MODE button for at least 3 seconds to switch between 1D/2D and RFID mode and the current mode light is on. Release the button, the current mode light is off. Solid amber: Charging Solid green: Fully charged Red flash/ Green and amber flash alternately: Charge error Solid red: Battery low warning (<20% capacity remaining.
Important Safeguards We recommend the use of Honeywell accessories and power adapters. Use of any non-Honeywell accessories or power adapters may cause damage not covered by the warranty. We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty. Ensure all components are dry prior to mating the unit and batteries with peripheral devices. Mating wet components may cause damage not covered by the warranty.
Support To search our knowledge base for a solution or to log into the Technical Support portal and report a problem, go to www.hsmcontactsupport.com. User Documentation For the user guide and other documentation, go to www.honeywellaidc.com. Limited Warranty For warranty information, go to www.honeywellaidc.com and click Get Resources > Product Warranty. Patents For patent information, see www.hsmpats.com. Trademarks The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
䕤ᇘᲈ䴆ໄᯢ ൟ᮴㒓⬉ᲈ䴆ঞ⡍ᅮᬊ⥛ 6$5 ⱘֵᙃ IH25 (900 MHz) Compliance Insert 䄺ਞ˖ ᴀ䆒ヺড়䰙䴲⬉⾏䕤ᇘֱᡸྨਬӮ ,&1,53 ǃ,((( & ǃ㕢㘨䙺䗮ֵྨਬӮᎹᡔᴃ䚼 2(7 %XOOHWLQ ǃࡴᣓ 566 ⌆⬉Ꮉᷛྨ࣪ޚਬӮ &(1(/(& 㾘ᅮⱘᇘ乥 5) 䕤ᇘᲈ䴆䰤ࠊDŽ 㒣䆌ৃ㗠Փ⫼㒓ঞ݊䰘ӊˈৃ㛑Ӯᇐ㟈ᴀѻકⱘヺড়ᗻ᮴ᬜˈৠᯊ䖬ৃ㛑Ӯᇐ㟈 5) ᲈ䴆䍙ߎᇍᴀ䆒ߎⱘ䰤ࠊDŽ For Users in English-Speaking Regions Caution: This marking indicates that the user should read all included documentation before use. Users of this product are cautioned to use accessories and peripherals approved by Honeywell.
Pour les utilisateurs canadiens Mise en garde : Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse. Les utilisateurs de ce produit sont avisés d’utiliser des accessoires et des périphériques approuvés par Honeywell. L’utilisation d’accessoires autres que ceux recommandés ou des changements à ce produit qui ne sont pas approuvés par Honeywell peuvent annuler la conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser l’équipement.
