Submittal Sheet

ManualsBrandsHoneywell ManualsDampers120V Non-Spring Return Foot Mounted Actuator w/ 2 Internal Aux. switches, 150 lb-in

PRODUCT DATA

63-2640-06

Series 71, 72, and 76

Modutrol IV™ Motors

APPLICATION

The Series 71, 72 and 76 Modutrol IV Motors are spring return

and non-spring return motors used to control dampers and

valves. The motors accept a current or voltage signal from an

electronic controller to position a damper or valve at any point

between open and closed.

FEATURES

• Replaces M734H,J,; M744S,T,Y; and M745L,S,T,Y

Motors.

• M7164, M7261, M7284, and M7294 are non-spring

return motors; M7282, M7285, M7286 and M7685 are

spring return motors.

• Integral spring return returns motor to normal position

when power is interrupted.

• Integral junction box provides NEMA 3 weather

protection.

• Motor and circuitry operate from 24 Vac. Models

available with factory installed transformer, or a field

added internal transformer.

• Quick-connect terminals are standard—screw terminal

adapter is available.

• Adapter bracket for matching shaft height of older

motors is available.

• Most motors have field adjustable stroke (90° to 160°).

• Die-cast aluminum housing.

• Integral auxiliary switches are available factory

mounted, or can be field added.

• Nominal timing standard of 30 seconds (90° stroke),

and 60 seconds (160° stroke). Other timings available.

• Spring return motors can operate valve linkages from

power end or auxiliary end shafts for normally closed

or normally open valve applications.

• All models have dual shafts (slotted and tapped on

both ends).

• All models have auxiliary switch cams.

• Fixed torque throughout the entire voltage range.

• Motors are designed for either normally open or

normally closed valves and dampers.

• Models available with adjustable start (zero) and span.

• Models available with 4 to 20 mA input signal.

• Models available with 2 to 10 Vdc input signal.

Contents

Application ........................................................................ 1

Features ........................................................................... 1

Specifications ................................................................... 2

Ordering Information ........................................................ 2

Installation ........................................................................ 5

Settings and Adjustments ................................................. 8

Operation and Checkout .................................................. 11

Summary of content (12 pages)

PAGE 1
Series 71, 72, and 76 Modutrol IV™ Motors PRODUCT DATA FEATURES • Replaces M734H,J,; M744S,T,Y; and M745L,S,T,Y Motors. • M7164, M7261, M7284, and M7294 are non-spring return motors; M7282, M7285, M7286 and M7685 are spring return motors. • Integral spring return returns motor to normal position when power is interrupted. • Integral junction box provides NEMA 3 weather protection. • Motor and circuitry operate from 24 Vac.
PAGE 2
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS SPECIFICATIONS Ambient Temperature Ratings: -40 to 150°F (-40 to 66°C). Models: TRADELINE models are selected and packaged to provide ease of stocking, ease of handling and maximum replacement value. TRADELINE model specifications are the same as those of standard models unless specified otherwise. IMPORTANT The specifications given in this publication do not include normal manufacturing tolerances.
PAGE 3
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS Fig. 1. Stroke VERTICAL REFERENCE FULLY CLOSED 10 VERTICAL REFERENCE VERTICAL REFERENCE 10 VERTICAL REFERENCE FULLY CLOSED 10 45 90 FULLY CLOSED FULLY CLOSED 160 160 90 FULLY OPEN FULLY OPEN FULLY OPEN 90 DEGREE STROKE 160 DEGREE STROKE 90 DEGREE STROKE FULLY OPEN 160 DEGREE STROKE Table 4. Modutrol IV Motors Series 2 Version Order Number Guide. M M Motor 71 72 76 72 10.5 - 13.
PAGE 4
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 4-1/16 (103) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222). FOR NON-SPRING RETUIRN MODELS 7-5/16 (185).
PAGE 5
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS Accessories: 220736A Internal Auxiliary Switch Kit; one switch. Can be field-installed. 220736B Internal Auxiliary Switch Kit; two switches, can be field-installed on TRADELINE models. 220738A Adapter Bracket raises motor shaft height by 3/4 in (19 mm) to match that of previous Modutrol Motor models. 220741A Screw Terminal Adapter converts the standard quickconnect terminals to screw terminals.
PAGE 6
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS To mount the motor with the bracket: 1. Mount the bracket to the equipment with existing or standard bolts. 2. Using the provided bolts, mount the motor to the bracket threaded holes. See Fig. 3. For valve linkage applications (other than the Q5001): 1. Mount the bracket to the linkage. 2. Position the motor on the bracket to align the motor shaft with the linkage. 3. Attach the motor to the bracket with the four bolts provided. See Fig. 4.
PAGE 7
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS 3. Replace wiring box cover. JUNCTION BOX MOTOR 1 L1 (HOT) T1 POWER END OF MOTOR CONTROLLER MOTOR Q5001 VALVE LINKAGE T2 - - + + F L2 24V 2 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQURED. 2 CONNECTING F TO – WILL DRIVE MOTOR TO FULLY OPEN. M5778 VALVE 1/4-20 UNC 1 in. LONG MOUNTING BOLTS Fig. 5. Typical system wiring. DAMPER MOTOR + C M18994 L1 (HOT) L1 L2 L2 R 1 MODULATING DC VOLTAGE SOURCE F Fig. 4.
PAGE 8
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS 4-20 mA CONTROLLER L1 L2 (HOT) SETTINGS AND ADJUSTMENTS 1 Before Setting Stroke MOTOR - - T1 + + T2 F 1. 2. 3. 2 MOTOR - T1 + T2 F IMPORTANT Detach linkage from motor before adjusting stroke. CAUTION 2 Careless Installation Hazard. Use of excessive force while adjusting cams damages the motor. To avoid damaging motor end switches, set cams by moving only the screwdriver top. MOTOR - T1 + T2 F Remove the top cover from the motor.
PAGE 9
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS Zero and Span Adjustment for M7284Q, M7285Q, and M7294Q 3. 4. M7284Q, M7285Q, and M7294Q actuators have the capability of adjustable zero and span. Fig. 10 shows the module with the zero and span potentiometers. 5. Zero: Sets input voltage to define the 0% angle of rotation. It is factory set to minimum position and can be adjusted to the maximum position of 20mA or 10V. 6. Span: Adjusts motor response to travel a full stroke through the selected input span.
PAGE 10
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS Motors with factory added auxiliary switches are shipped in the closed position (fully counterclockwise, as viewed from the motor power end) with auxiliary cams set to actuate switches 30° from the closed position and to provide 1° degree differential. With the motor in the closed (fully counterclockwise) position, the auxiliary switch breaks contacts R-B. See Fig. 12 for auxiliary switch wiring.
PAGE 11
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS MOVE SCREWDRIVER AT TOP ONLY TO ADJUST CAM. NOTE: CAMS ARE OFFSET VERTICALLY TO PROVIDE BETTER VIEW OF BACK CAM. 1/8 INCH STRAIGHT-BLADE SCREWDRIVER SLOW RISE PORTION (APPROX. 10 DIFF.) RIGHT/INNER AUXILIARY SWITCH INNER AUXILIARY CAM (BLUE) FAST RISE PORTION (APPROX. 1 DIFF.) LEFT/OUTER AUXILIARY SWITCH FAST RISE PORTION (APPROX. 1 DIFF.) OUTER AUXILIARY CAM (RED) SLOW RISE PORTION (APPROX. 10 DIFF.
PAGE 12
SERIES 71, 72, AND 76 MODUTROL IV™ MOTORS Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Registered Trademark © 2009 Honeywell International Inc. 63-2640—06 E.K. Rev.