Portable Air Conditioner (Dual Hose) User Manual Read and save these instructions before use Model: MN10CED / MN10CHED MN12CED / MN12CHED MN14CED / MN14CHED Series Customer Support: Web: www.jmatek.com USA: 1-800-474-2147 | usinfo@jmatek.com CANADA^: 1-888-209-0999 | canadainfo@jmatek.com ^ Canada Customer Support service available for models sold in Canada only.
SAFETY READ AND SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. IN CASE THERE IS ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL PREVAIL. WARNING: • DO NOT operate the unit with a damaged plug or loose wall outlet.
SAFETY (CONTINUED) • This appliance has been manufactured for use in domestic environments and should not be used for other purposes. • Only use the installation kit provided to install this unit. DO NOT attempt to extend the exhaust Hose or install this unit using other methods other than that shown in this manual. Improper installation will void any existing warranties. • DO NOT use an extension cord with this unit.
THANK YOU Congratulations on your purchase of this Honeywell Portable Air Conditioner. Regarding the information pertaining to the installation, handling, servicing, cleaning and disposal of the appliance, please refer to the below paragraph of the manual. USER TIPS Portable Air Conditioners are ideal for spot cooling. The compressor, condenser and evaporator are housed in a compact unit. The air is dehumidified and cooled while a flexible exhaust Hose sends heat outside.
PARTS DESCRIPTION 5 2 6 1 11 3 9 12 10 8 4 1) Control Panel (Incl.
INSTALLATION It is important that the installation instructions below are followed for successful installation of this Portable Air Conditioner. Please call Customer Support if you have any difficulties or queries regarding these installation procedures. 1 2 3 x1 x2 4 x2 5 x2 x2 Installation Kit: 1. Window Bracket Kit (1 Set) 2. Window Bracket Panel Adapter (2 Pieces) Dia. 5.9" (15 cm) Dia. 5.1"(13 cm) 3. Hose Connector Dia. 5.9" (15 cm) Dia. 5.1" (13 cm) 4. Hole Cover (2 Pieces) 5.
INSTALLATION (CONTINUED) 2. The Window Brackets allow you to install to windows and balcony doors of different heights or width. 19.7" (50 cm) 1 part 19.7" (50 cm) to 38.2" (97 cm) 2 parts 47.2" (1.2 m) 3 parts Adjustable Knobs To install the window bracket to the window frame, you need to adjust the height or width of the window bracket by extending the length according to the height or width of the window.
INSTALLATION (CONTINUED) 4. Connect the window bracket to the window bracket panel adapters. Slide-in the window bracket panel adapter for the Hose with diameter of 5.9" (15 cm) then rotate anti-clockwise until it is locked in place. Slide-in the window bracket panel adapter for the Hose with diameter of 5.1" (13 cm) then rotate clockwise until it is locked in place. 5. Connect the window bracket to the window. 6. The Portable Air Conditioner is now ready to use.
INSTALLATION (CONTINUED) IMPORTANT: Do not replace or lengthen the exhaust Hose as this could cause the unit to malfunction. NOT RECOMMENDED MIN 35.6 cm MAX. 14" (36 cm) MAX. 40" (102 cm) 20" (50 cm) RECOMMENDED WARNING: Any warranties included with this product will be voided if an extra extension Hose is added to the originally provided installation kit or if the installation is performed differently than the manufacturer's instructions, without proper consultation.
USE AND OPERATION CONTROL PANEL (6) (5) (4) (4) (3) (1),(2) 1) Power Control / Standby Mode 4) Timer / Temperature Set Controls 2) Warning Light (when flashing) 5) Fan Speed Control 3) Mode Control 6) Timer Control FUNCTION BUTTONS POWER CONTROL The Power Control turns the unit on and off. When the unit is plugged in, this button lights up indicating it is in a Standby Mode ready to be switched on anytime. WARNING LIGHT Condensation may accumulate in the unit.
USE AND OPERATION (CONTINUED) FUNCTION BUTTONS (CONTINUED) • Dehumidifying Mode Air is dehumidified as it passes through the unit, without being in full cooling mode. If room temperature is higher than 25°C (77°F) fan speed can be adjusted; otherwise fan speed is preset to LOW. Note: If the unit will be used mainly as a dehumidifier, do not connect the exhaust Hoses. Continuous drainage is then necessary (refer to Continuous Draining for Dehumidifier Mode).
USE AND OPERATION (CONTINUED) FUNCTION BUTTONS (CONTINUED) TEMPERATURE / TIMER SET CONTROLS • Used for adjusting the timer and thermostat. • The default display is setting temperature. • In cooling mode, when ▼ or ▲ button is pressed, the set temperature is displayed and may be adjusted. After 10 seconds the display will revert back to room temperature. Temperature is only adjustable in cool mode. The time is adjustable between 1 - 24 hours.
USE AND OPERATION (CONTINUED) REMOTE CONTROL The functions work the same as the Portable Air Conditioner's Control Panel. All key functions can be accessed from the remote control. Temperature / Timer Set • Used for adjusting the timer and temperature. • When the ▼ or ▲ key is pressed, the set temperature is displayed and may be adjusted • Timer setting is available from 1 - 24 hours by pressing the key ▼ or ▲.
CLEANING AND MAINTENANCE Appliance Maintenance: 1. Turn off the appliance before disconnecting the power supply. 2. Only clean the appliance with a soft dry cloth. Dust Filter Maintenance: The dust filter is to be cleaned every two weeks to maintain air cooling efficiency. Please follow the below instructions for cleaning the dust filter: 1. Switch off and unplug the air conditioner from the electrical outlet. 2 . Remove the Upper Dust Filter. 3 .
CLEANING AND MAINTENANCE (CONTINUED) 5. Disconnecting the Window Installation Kit: • • • • Remove the Hose from the air exhaust outlet by rotating anti-clockwise to unlock the knob mechanism then sliding out. Remove the Hose from the air intake outlet by rotating clockwise to unlock the knob mechanism then sliding out. Remove the window bracket panel adapter for the Hose with diameter of 5.9" (15 cm) from the window bracket by rotating clockwise then pulling away.
WATER CONDENSATION DRAINAGE When there is excess water condensation inside the unit, the air conditioner stops running and shows a warning light (the Power Control button flashes with a red light). This warning light indicates that the water condensation needs to be drained using the following procedures: Manual Draining in Cooling, Dehumidifying and Heating* Modes Water may need to be drained in high humidity areas. 1. Unplug the unit from power source. 2.
WATER CONDENSATION DRAINAGE (CONTINUED) Continuous Draining for Dehumidifier Mode While using the unit in dehumidifier mode, continuous drainage is recommended. 1. Unplug the unit from power source. 2. Remove the upper rubber drain plug. Some residual water may spill so please have a pan to collect the water. See diagram. 3. Connect the drain connector to a ¾" Hose or standard garden Hose (not included). 4. The water can be continuously drained through the drain tube into a floor drain or bucket. 5.
TROUBLESHOOTING GUIDE The following troubleshooting guide addresses the most common problems. If problems persist, call customer support. Unplug and disconnect the appliance from the power source before attempting to troubleshoot. PROBLEM The air conditioning unit does not start Runs a short while only POSSIBLE CAUSE SOLUTION No electricity. Check for power. Batteries in the remote control need to be replaced. Change remote control batteries. The power cord is not properly plugged in.
TROUBLESHOOTING GUIDE (CONTINUED) PROBLEM POSSIBLE CAUSE SOLUTION A door or window is open. Make sure the window or door is closed. Runs but not cooling Will not run and Power button is blinking (water full indicator) The dust filter is dirty. Clean the dust filter. One or both of the Hoses are detached. Reinstall Hoses properly (refer to Installation section). Temperature setting is too high. Reduce temperature setting on control panel. Air outlet or intake is blocked. Remove blockage.
TROUBLESHOOTING GUIDE (CONTINUED) PROBLEM POSSIBLE CAUSE SOLUTION Heating function not Check that the Heating function has been activated. activated yet. will be illuminated when the The ambient temperature Heater is switched ON. is too high. Heater* is not switching ON. Heating is activated only when the ambient temperature is below 25°C (77°F). Switch on the Heating function when the ambient temperature reaches below 25°C (77°F). *Applicable for models with Heating feature only.
JMATEK North America LLC Mahwah, New Jersey 07495 USA Email: usinfo@jmatek.com Web: www.jmatek.com Made in China © 2019 JMATEK Limited. All rights reserved. The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured by Airtek Int'l Corp. Ltd. (subsidiary of JMATEK Ltd.).