Submittal Sheet

SPECIFICATION DATA
Put Bar Code Here
63-1296-03
MSXX10 Series
88 LB-IN (10 NM) SPRING RETURN
DIRECT COUPLED ACTUATORS
N314
MS4110, MS7510, MS8110 S10 Series Spring Return Direct
Coupled Actuators (DCA) are used within heating, ventilating,
and air-conditioning (HVAC) systems. They can drive a variety
of quarter-turn, final control elements requiring spring return
fail-safe operation. Applications include:
Volume control dampers, mounted directly to the drive
shaft or remotely (with the use of accessory hardware).
Quarter-turn rotary valves, such as ball or butterfly valves
mounted directly to the drive shaft.
Linear stroke globe or cage valves mounted with linkages
to provide linear actuation.
FEATURES
Brushless DC submotor with electronic stall protection
for floating/modulating models.
Brush DC submotor with electronic stall protection for
2-position models.
Self-centering shaft adapter (shaft coupling) for wide
range of shaft sizes.
Models available for use with two-position, single pole
single throw (spst), line- (Series 40) or low- (Series 80)
voltage controls.
Models available for use with floating or switched
single-pole, double-throw (spdt) (Series 60) controls.
Models available for use with proportional current or
voltage (Series 70) controls.
Models available with combined floating/modulating
control in a single device.
Models available with adjustable zero and span.
Models available with line-voltage internal end switches.
Models available with 3-foot, 18 AWG color-coded
cable.
Access cover to facilitate connectivity.
Metal housing with built-in mechanical end limits.
Spring return direction field-selectable.
Shaft position indicator and scale.
Manual winding capability with locking function.
UL (cUL) listed and CE compliant.
All Models are plenum-rated per UL873.
SPECIFICATIONS
Torque Ratings:
Typical Holding, Driving, Spring Return: 88 lb-in. (10 Nm).
Stall Maximum (fully open at 75°F): 200 lb-in. (22.6 Nm).
Electrical Ratings:
See Table 3.
Electrical Connections:
Field wiring 14 to 22 AWG (2.0 to 0.344 mm sq) to screw
terminals, located under the removable access cover.
Stroke:
95° ±3°, mechanically limited.
Controller Type:
See Models.
Modulating (Series 70) or Floating (Series 60); controlled
by selector switch.
Input Impedance: 95K ohms minimum.
Feedback Signal: 0 or 2-10 Vdc;
Driving current is 3 mA minimum.
Timing (At Rated Torque and Voltage):
Drive Open (typical):
Floating, Modulating Models: 90 seconds.
Two-Position Models: 45 seconds ±5 seconds.
Spring Close: 20 seconds typical.
Temperature Ratings:
Ambient: -40°F to 140°F (-40°C to 60°C).
Shipping and Storage: -40°F to 158°F (-40°C to 70°C).
Humidity Ratings:
5% to 95% RH noncondensing.
Design Life (at Rated Voltage):
Two-position models: 50,000 full stroke cycles;
50,000 full stroke spring returns.
Floating and Modulating models: 60,000 full stroke cycles;
1,500,000 repositions; 60,000 full stroke spring returns.
End Switches (Two SPDT):
Dry Contact
Settings (fixed): 7° nominal stroke, 85° nominal stroke.
Ratings (maximum load): 250 Vac, 5A resistive.
Dimensions:
See Fig. 1.
Device Weight:
6 lb (2.7 kg)
Mounting:
Self-centering shaft adapter (shaft coupling).
Round Damper Shafts: 0.375 to 1.06 in. (10 to 27 mm).
Square Damper Shafts: 1/2 to 3/4 in. (13 to 19 mm).
Actuator can be mounted with shaft in any position.
Minimum Damper Shaft Length:
1 in. (25 mm); 3 in. (76 mm) recommended.
Noise Rating at 1m (Maximum):
Holding: 20 dBA (no audible noise).
Two-position models:
Driving: 50 dBA.
Spring Return: 65 dBA.
Floating and Modulating models:
Driving: 40 dBA.
Spring Return: 50 dBA.
Vibration:
Not suitable for high vibration applications (Example
installation environment: Truck Trailers or Railroad Cars)
Acceptable Vibration Levels 0.6g at 30 to 300 Hz.
Environmental Protection Ratings:
NEMA2 (US Models) or IP54 (European Models) when
mounted on horizontal shaft with access cover below the
shaft.
Approvals:
UL/cUL.
UL873 Plenum Rating, File No. E4436; Guide No. XAPX.
CE.
C-TICK.

Summary of content (2 pages)