Atomic Projection Clock User Manual

ManualsBrandsHoneywell ManualsClockPCR11ELW

Atomic Projection Clock

with Temperature

(PCR11ELW)

USER MANUAL

INTRODUCTION

Thank you for selecting the Honeywell Atomic Projection Clock

with Temperature. This device includes precise time keeping,

alarm, moonphase, temperature monitoring and projection

features that you can use from the comfort of your home.

In this package you will find:

¥ Atomic Projection Clock with Temperature

¥ AC/DC adaptor

Please keep this manual handy as you use your new item. It

contains practical step-by-step instructions, as well as technical

specifications and precautions you should know.

Summary of content (9 pages)

PAGE 1
Atomic Projection Clock with Temperature (PCR11ELW) USER MANUAL INTRODUCTION Thank you for selecting the Honeywell Atomic Projection Clock with Temperature. This device includes precise time keeping, alarm, moonphase, temperature monitoring and projection features that you can use from the comfort of your home. In this package you will find: ¥ Atomic Projection Clock with Temperature ¥ AC/DC adaptor Please keep this manual handy as you use your new item.
PAGE 2
SNOOZE/ Backlight/ Projection Light key FEATURES * Current time image is projected onto the wall or ceiling in bright red digits. * Precise time and date are set via RF signal from the US Atomic Clock in Colorado.
PAGE 3
1 ATOMIC DISPLAYING PROJECTED INFORMATION CONTINUOUSLY Connect AC/DC adapter as shown below. CLOCK PM DATE 1 CONTINUE PROJECTION MONTH SET 2 SET DC 3V MODE 2 SIZE AA/UM3 ROTATE SIZE AA/UM3 3 4 Battery compartment FLIP Use 2 X AA, 1.5V batteries and AC-DC adapter (AC120V, 60Hz-DC3V, 100mA) included. Important: Please make sure your household voltage matches the voltage supported by the adapter, or it will damage your clock and adapter.
PAGE 4
ATOMIC TIME AND WWVB SIGNAL The NIST (National Institute of Standards and Technology) radio station is located in Ft. Collins Colorado. It transmits an exact time signal continuously throughout the continental United States at 60 KHz frequency. The Atomic Projection Clock with Temperature can receive this WWVB signal through its internal antenna from up to 2,000 miles away. Due to the nature of the Earth’s ionosphere, reception can be limited during the daylight hours.
PAGE 5
DISPLAYING TEMPERATURE AND ALARMS *Press MODE to display the ALARM 1 time: MONTH *Press MODE again to display the Alarm 2 time: DATE DATE ALARM 2 DATE SETTING TIME AND DATE MANUALLY The time piece date and time can be set by pressing and holding the MODE buttons for 3 seconds in Time/Temperature display with the atomic time receiver disabled. To disable atomic time receiver, press and hold [ — ] key until the atomic reception icon will appear from the display.
PAGE 6
SETTING 12 OR 24 HOUR TIME FORMAT *Pressing "+" will display time in 12 or 24 hour format. N.B.:1. If no key pressed within 30 seconds, the clock returns to the Time / Temperature Display setting. 2. During any programming press and hold UP [+] or DOWN [–] key for 2 seconds for faster scrolling through the digits.
PAGE 7
Activating the Alarm When the ALARM 1 or ALARM 2 is ringing, the relative alarm icon [ 1 ] or [ 2 ] will be flashing. * Press SET1 / SET2 key to turn the alarm off. * Press button 1 - alarm stops and the backlight will turn on for 5 seconds with the repeat alarm indicator ( ZZ) flashing. * If the alarm is not turned off, it will stop in 4 minutes. *Turn the 4 [FOCUS] key knob to adjust the focus of projected image. * Press 3 [FLIP] key to rotate the projection image 180˚ clockwise.
PAGE 8
5. Only use fresh batteries as specified in the user’s manual. Do not mix new and old batteries as the old ones may leak. Always replace both batteries at the same time. 6. Always read the user’s manual thoroughly before operating the unit. 7. Replace the batteries promptly when necessary (display becomes dim) or store the batteries when not in use. 8. A soft cloth or paper towel may be used to clean your unit. 9. Keep the unit clean and dry to avoid any problems.
PAGE 9
STANDARD WARRANTY INFORMATION This product is warranted from the manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.hidekielectronics.us. Click Online Product Registration under the Customer Service menu.