Glowfly Q3200U Installation Instructions

ManualsBrandsHoneywell ManualsReplacement PartsGlowfly™ Hot Surface Ignitor

Table Of Contents

INSTALLATION INSTRUCTIONS

69-2334EF-01

Q3200U/Q3205U Universal Hot

Surface Igniter Kit

Fig. 1.

APPLICATION

The Q3200U and Q3205U Universal Hot Surface igniter

Kit is designed to provide a robust field service

replacement igniter in gas fired appliances with Norton /

St Gobain 12Vac Silicon Carbide Hot Surface Igniters.

They use a 120 Volt Silicon Nitride igniter designed with

long life and high resistance to damage or burn out in the

appliance. The kit includes the specially designed silicon

nitride igniter and six different bracket configurations to

adapt the igniter to the specific appliance application

along with accessory parts to allow mounting and wiring

of the igniter. Clear instructions and application templates

are provided to simplify selection of the proper bracket

and ease installation of the replacement.

BEFORE YOU START

1. Review this instruction sheet fully to ensure you are

familiar with the steps and information necessary to

complete the installation properly, including the

WARNING section on this page.

2. Confirm the existing hot surface igniter has failed:

a. Run an appliance cycle and observe the installed

igniter.

b. If the igniter glows, the problem is not the igniter.

c. If the igniter does not glow during an ignition

cycle:

(1) Unplug the igniter lead wires.

(2) Set a voltmeter’s scale to 300 VAC and con-

nect the voltmeter to the igniter harness.

(3) Run another cycle and confirm 120 VAC

power at the harness during the igniter warm

up time.

3. Check the appliance construction and wiring dia-

gram (typically located on an appliance panel) and

confirm that the appliance does not use the hot sur-

face igniter as the flame sensor. Do not use the

Q3200 or Q3205 kit if the existing igniter is also the

flame sensor. Use an original equipment part. The

Q3200/Q3205 is not designed to be used as a flame

sensor.

4. If the appliance is a sealed combustion model,

determine if the existing hot surface igniter ceramic

is part of the sealing of the burner box. If it is, check

carefully to determine if this kit will allow the proper

appliance function.

5. Confirm the kit components:

a. six brackets stamped A, B, C, D, E, and F

b. one hot surface igniter with wiring leads

c. two wire nuts and a thread forming screw

6. The Q3200/Q3205 should not be handled by the

black silicon nitride igniter. Use care to handle the

Q3200/Q3205 by the ceramic casing or the bracket.

INSTALLATION

When Installing This Product…

Read these instructions carefully. Failure to follow them

could damage the product or cause a hazardous condi-

tion.

2. Check the cross reference table on page 5 and the

templates (Fig. 2 on page 3 and Fig. 3 on page 4) to

make sure the proper igniter bracket is used for your

application.

1-25/32

(45)

2-19/64

(58)

1-23/64

(35)

2-13/16

(72)

3-23/64

(85)

15-45/64

(399)

GLOWFLY

GLOWFLY PRO

1-21/32

(42)

15-45/64

(399)

M37744

Summary of content (12 pages)

PAGE 1
Q3200U/Q3205U Universal Hot Surface Igniter Kit INSTALLATION INSTRUCTIONS BEFORE YOU START 1. 1-21/32 (42) 1-25/32 (45) 2-19/64 (58) 1-23/64 (35) 2. 3-23/64 (85) 2-13/16 (72) 3. 15-45/64 (399) 15-45/64 (399) 4. GLOWFLY GLOWFLY PRO M37744 5. Fig. 1. APPLICATION The Q3200U and Q3205U Universal Hot Surface igniter Kit is designed to provide a robust field service replacement igniter in gas fired appliances with Norton / St Gobain 12Vac Silicon Carbide Hot Surface Igniters.
PAGE 2
Q3200U/Q3205U UNIVERSAL HOT SURFACE IGNITER KIT 3. 4. This product is intended for installation by a trained and experienced service technician. If a service technician is not available, the individual installing this product must be knowledgeable in the design, construction, and operation of the gas fired appliance being serviced. After installation is complete, check out appliance operation as provided in these instructions. WARNING Fire or Explosion or Electrical Shock Hazard.
PAGE 3
Q3200U/Q3205U UNIVERSAL HOT SURFACE IGNITER KIT 4. 5. 6. 7. Remove the call for heat signal. Turn the gas supply on. Initiate a call for heat. Observe the light off sequence and confirm that the appliance lights properly and stays lit once the actual gas flow starts. If the appliance lights and the main flame stays stable, remove the call for heat and allow the shut down sequence to be completed. Repeat step 6 two more times to assure the light off of the appliance is reliable.
PAGE 4
Q3200U/Q3205U UNIVERSAL HOT SURFACE IGNITER KIT A 1 TAB 1 HONEYWELL BRACKET AND ASSY (NOT TO SCALE) 2 HOLE FOR 1 THREAD FORMING SCREW TAB 2 BRACKET A F 2 5/32 (54.7) [ACTUAL] PLACE REMOVED IGNITER OVER TEMPLATE OUTLINE USE BRACKET C 2 5/16 (58.4) [ACTUAL] USE BRACKET D 2 5/16 (58.4) [ACTUAL] USE BRACKET E 2 ORANGE GASKET FOR BRACKET E, REUSE ORANGE GASKET FROM IGNITER BEING REPLACED. EACH BRACKET HAS A HOLE FOR THE THREAD FORMING SCREW, WHICH IS INCLUDED IN THE IGNITER KIT.
PAGE 5
Q3200U/Q3205U UNIVERSAL HOT SURFACE IGNITER KIT Table 1. Igniter Bracket Replacement Cross Reference.a Mfr. American Road Equip. Arco Air Q3200 Bracketb OEM # 201W A 1096048 D 1380680 D Armstrong 38322B001 Air A Mfr.
PAGE 6
Q3200U/Q3205U UNIVERSAL HOT SURFACE IGNITER KIT Resideo Inc., 1985 Douglas Drive North, Golden Valley, MN 55422 www.resideo.com 69-2334EF—01 M.S. 01-19 | Printed in United States ©2019 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International Inc.
PAGE 7
Trousse universelle d’allumeur par incandescence Q3200U/Q3205U NOTICE D’INSTALLATION AVANT DE COMMENCER 1. 1-21/32 (42) 1-25/32 (45) 2-19/64 (58) 1-23/64 (35) 3-23/64 (85) 2-13/16 (72) 15-45/64 (399) 15-45/64 (399) GLOWFLY GLOWFLY PRO M37744 2. 3. 4. Fig. 1.
PAGE 8
TROUSSE UNIVERSELLE D’ALLUMEUR PAR INCANDESCENCE Q3200U/Q3205U INSTALLATION Lors de l'installation de ce produit... 1. 2. 3. 4. Lire attentivement ces instructions. Le non-respect des instructions peut endommager le produit ou provoquer une situation dangereuse. Vérifier le tableau des références à la page 5 et les modèles (Fig. 2 page 3 et Fig. 3 page 4) pour s'assurer que le support d'allumeur adéquat est utilisé en fonction de l'application.
PAGE 9
TROUSSE UNIVERSELLE D’ALLUMEUR PAR INCANDESCENCE Q3200U/Q3205U 5. 6. Repérer le faisceau de câblage de l'allumeur de l'appareil. Couper le connecteur et dénuder les deux fils de 6 mm (1/4 po). Utiliser les serre-fils fournis pour attacher les fils de l'allumeur au faisceau de câblage de l'appareil. Les fils de l'allumeur peuvent être coupés si nécessaire. Les dénuder de 6 mm (1/4 po) avant de les attacher au faisceau de câblage de l'appareil. Vérifier l'installation 1. 2. 3. 4. 5. 6. 7.
PAGE 10
TROUSSE UNIVERSELLE D’ALLUMEUR PAR INCANDESCENCE Q3200U/Q3205U PLACER L’ALLUMEUR RETIRÉ SUR LE TRACÉ DU MODÈLE UTILISER LE SUPPORT A. RETIRER LA LANGUETTE 1. 2 5/16 (58,4) [ACTUEL] UTILISER LE SUPPORT A. RETIRER LA LANGUETTE 1. 2 5/16 (58,4) [ACTUEL] UTILISER LE SUPPORT A. RETIRER LA LANGUETTE 2.
PAGE 11
TROUSSE UNIVERSELLE D’ALLUMEUR PAR INCANDESCENCE Q3200U/Q3205U Tableau 1. Références pour le remplacement du support de l'allumeura Fabricant American Road Equip.
PAGE 12
TROUSSE UNIVERSELLE D’ALLUMEUR PAR INCANDESCENCE Q3200U/Q3205U Resideo Inc., 1985 Douglas Drive North, Golden Valley, MN 55422 www.resideo.com 69-2334EF—01 M.S. 01-19 | Imprimé aux États-Unis ©2019 Resideo Technologies, Inc. Tous droits réservés. La marque de commerce Honeywell Home est utilisée sous licence avec l’autorisation d’Honeywell International Inc.