T9 THERMOSTAT Installation Guide Online Guides honeywellhome.com 33-00421ES_A.
Read before installing. Included in your box: Installation Guide Screws and anchors T9 Wi-Fi Thermostat Wireless room sensor UWP Wallplate C-Wire Adapter (optional) Wire labels Tools you will need: You may need: Phillips screwdriver Wire Stripper Small flat head screwdriver Needle-nose pliers Pencil Level Home Wi-Fi Password Drill and drill bit (7/32in) Flashlight 2 33-00421ES_A.
Compatibility Section • REQUIRED: A C-Wire (common wire) is needed for 24 VAC power. If you do not have a C-Wire, then a C-Wire Adapter is provided. This guide will help you determine if you have a C-Wire or will need to use the included C-Wire Adapter (Step 10). The C-Wire is a wire that originates from your heating and cooling system and needs to be connected to the C terminal on your thermostat. There is no universal color used to designate this type of wire.
Removing your old thermostat You will need: Screwdriver, needle-nose pliers 1 Turn off power ON To protect your equipment, turn off the power at the breaker box or switch that controls you heating and cooling equipment. Note: The thermostat off switch will not turn off the power to the equipment. OFF OR OFF Switch Breaker box 2 Check that your system is off Change the temperature on your old thermostat so that your system starts heating or cooling.
Compatibility Check 4 Do you have a line voltage system? Line voltage systems have thick black wires with wire nuts or are labeled high voltage (120V or higher). YES Your system is not compatible. Call 1-855-733-5465 to find a proinstaller in your area. Wire nut Thick black wire NO Continue to the next step. 5 Take a picture of your existing wall plate’s wiring In order to capture all of the letters next to the terminals, be sure to take multiple pictures from different angles.
8 Write down the colors of the wires Check the boxes and write down the color of the wires connected to terminals that are coming from the wall. Check all that apply (not all will apply). Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ Wire Color Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ A or L/A C Required* E G K O/B U (1 or 2) Wire Color R Rc Rh W W2 or Aux Y Y2 *A C-wire or C-Wire Power Adapter (included) is required. If there are wires in terminals that are not listed, you will need additional wiring support. Visit honeywellhome.
Only complete this section if you answered No to Step 10 Connecting Your Unused C-Wire You will need: Screwdriver, flashlight, wire strippers Compatibility Check 11 Do you have a zoning panel? You have a zoning panel if you have multiple thermostats and one furnace or heating system. Furnace YES Thermostat C-Wire Adapter installation is more complicated on zoned systems. Call 1-855-733-5465 to find a pro-installer. Zoning Panel NO Proceed to the next step.
14 Remove cover from furnace or heating system Open the heating and cooling system’s cover to find the control board. You should see the same terminal labels that are on your thermostat. Note: You may need to unscrew the cover. The control board may be at the top or bottom. G C R W Y 15 Find the other end of the unused wire Locate the bundle of wires that are the same as the ones at your thermostat. The unused wire should be the same color as the one near your existing thermostat.
Installing Your New Thermostat You will need: Level, pencil, drill and a 7/32in drill bit Thermostat Screws UWP wallplate Anchors Wall 9 33-00421ES_A.
18 Position wall plate Pull open the wall plate that was included with your new thermostat. Insert the bundle of wires through the back of the wall plate. - Make sure at least 1/4-inch of each wire is exposed for easy insertion into the wire terminals. UWP 19 Insert recommended wall anchors It is recommended that you use the wall anchors included in the box to mount your thermostat. You can use the wall plate to mark where you want to place the wall anchors.
20 Determine Correct R-Switch Position and Insert R-wire or wires Set the R-switch up or down based on your wiring notes in Step 8. Insert wires into the inner holes of the terminals on the wall plate. The tabs will stay down once the wire is inserted. If you have 1 R-Wire (R, RC, RH): 1. Ensure the right R-switch is in the up position. 2. Insert your R-wire (R, Rh or Rc) into R-terminal. OR If you have 2 R-Wires (R, RC, RH): 1. Set right R-switch to the down position. 2.
22 Close the door and mount the wall plate Mount the wall plate using the provided screws. Install all three screws for a secure fit on your wall. Tip: Prior to tightening the screws, use a level to ensure the wall plate is level. 23 Attach your thermostat Align the thermostat on the wall plate and firmly snap into place. Go back to your circuit breaker box. 24 Turn power back on Turn on the switch that controls your heating and cooling system.
Getting the most from the T9 Wi-Fi Thermostat Prioritize Rooms Prioritize a specific room or multiple rooms, or let comfort follow your move using built-in motion detection. Control on the Go Adjust your thermostat from anywhere using your tablet or smartphone. Save Energy With geofencing, you can save money on the most expensive part of your energy bill while you’re away. Simple Installation The thermostat automatically programs itself.
Using your thermostat The screen will wake up by pressing the center area of the displayed temperature. Indoor Temperature Displays the current indoor temperature. Current Priority Displays the type of priority and number of rooms being prioritized. Extend your thermostat’s reach with additional Wireless Room Sensors. Indoor Humidity Displays the current indoor humidity. 2 18% 74 Adjust Temperature Touch the up and down arrows to set your desired temperature.
Using Priority Priority creates an average temperature in your home based on specific rooms. This allows you to prioritize comfort where you want it. Selected Rooms Rooms you manually select create an average temperature in your home. 72 72 72 72 Unselected Room Will not contribute to the average temperature. Selected Room Will contribute to the average temperature. Active Rooms Rooms with detected motion are automatically selected to create an average temperature in your home.
Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • • Check circuit breaker and reset if necessary. Make sure power switch for heating & cooling system is on. Make sure furnace door is closed securely. Make sure the C wire is connected. Heating or cooling system does not respond • Press Menu > System Mode > Heat > Done to set the system to Heat mode.
2-year limited warranty Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of two (2) years from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).
Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422 www.resideo.com ©2018 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International Inc. 33-00421ES—02 M.S. 11-18 Printed in Mexico 33-00421ES_A.
TERMOSTATO T9 Guía de instalación Guías en línea honeywellhome.com 33-00421ES_A.
Leer antes de instalar. Contenido de la caja: Guía de instalación Tornillos y anclajes Accesorio del termostato T9 con conexión wifi Sensor inalámbrico para habitación Placa de pared UWP Adaptador para el cable C (opcional) Etiquetas de cableado Necesitará las siguientes herramientas: Podría necesitar: Destornillador Phillips Pelacables Destornillador plano pequeño Alicates de punta Lápiz Nivel Contraseña de la red wifi del hogar Taladro y broca (7/32”) Linterna 2 33-00421ES_A.
Sección de compatibilidad • REQUERIMIENTOS: Se requiere un cable C (común) para una alimentación de 24 V CA. Si no tiene un cable C, se suministra un adaptador del cable C. La presente guía lo ayudará a determinar si tiene un cable C o necesitará usar el adaptador del cable C provisto (paso 10). El cable C es un cable que sale de su sistema de calefacción y refrigeración y debe conectarse a la terminal C del termostato. No hay un color que se use universalmente para designar este tipo de cable.
Quitar el termostato anterior Necesitará lo siguiente: Destornillador, alicates de punta 1 Desconecte el suministro de energía ON Para proteger el equipo, desconecte el suministro de energía en el interruptor o la caja de disyuntores que controla el equipo de calefacción y refrigeración. Nota: El interruptor de apagado del termostato no interrumpirá el suministro de energía del equipo.
Verificación de compatibilidad 4 ¿Tiene un sistema de tensión de línea? Los sistemas de tensión de línea tienen cables negros y gruesos con conectores de cable o se etiquetan como de alto voltaje (120 V o superior). SÍ Conector de cables Su sistema no es compatible. Llame al 1-855-733-5465 para obtener información sobre un instalador profesional en su área. Cable negro y grueso NO Continúe con el siguiente paso.
8 Anote los colores de los cables Marque las casillas y anote el color de los cables conectados a las terminales que salen de la pared. Marque todos los que correspondan (no todos corresponderán). Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ Color de cable Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ A o L/A C Requerido* E G K O/B U (1 o 2) Color de cable R Rc Rh W W2 o Aux Y Y2 *Se requiere un cable C o un adaptador del cable C (incluido).
Complete esta sección solamente si respondió No en el paso 10 Conexión del cable C no usado Necesitará lo siguiente: Destornillador, linterna, pelacables Verificación de compatibilidad 11 ¿Tiene un panel de zonas? Tiene un panel de zonas si cuenta con varios termostatos y un sistema de calefacción o caldera. Caldera SÍ Termostato La instalación del adaptador del cable C es más complicada en sistemas con zona. Llame al 1-855-733-5465 para obtener un instalador profesional.
14 Retire la cubierta del sistema de caldera o calefacción Abra la cubierta del sistema de calefacción o refrigeración para ubicar la tarjeta de control. Debería ver las mismas etiquetas de terminales que se encuentran en el termostato. Nota: Es posible que necesite desatornillar la cubierta. La tarjeta de control puede encontrarse en la parte superior o en la inferior. G C R W Y 15 Encuentre el otro extremo del cable sin usar Ubique el conjunto de cables que son iguales a los del termostato.
Instalación del termostato nuevo Necesitará lo siguiente: Nivel, lápiz, taladro y una broca de 7/32” Termostato Tornillos Placa de pared UWP Anclajes Pared 9 33-00421ES_A.
18 Posicione la placa de pared Abra la placa de pared provista con el termostato nuevo. Inserte el conjunto de cables por el orificio que se encuentra en la parte trasera de la placa de pared. - Asegúrese que haya al menos 1/4 pulgada de cada cable expuesto para que sea más fácil la inserción en las terminales de cableado. UWP 19 Inserte los anclajes de pared recomendados Se recomienda que use los anclajes de pared provistos en la caja para montar el termostato.
20 Determine la posición correcta del interruptor R e inserte el/los cable/s R Establezca el interruptor R hacia arriba o abajo según las notas de cableado del paso 8. Inserte los cables por los orificios interiores de las terminales de la placa de pared. Las pestañas se mantendrán abajo una vez que se inserten los cables. Si tiene 1 cable R (R, RC, RH): 1. Asegúrese que el interruptor R derecho se encuentre hacia arriba. 2. Inserte el cable R (R, Rh o Rc) en la terminal R.
22 Cierre la puerta y monte la placa de pared Monte la placa de pared con los tornillos provistos. Instale los tres tornillos para lograr un ajuste seguro en la pared. Sugerencia: Antes de ajustar los tornillos, use un nivel para asegurarse que la placa de pared esté nivelada. 23 Fije el termostato Alinee el termostato con la placa de pared y empújelo con firmeza para ajustarlo en su lugar. Vuelva a la caja de disyuntores del circuito.
Aprovechar al máximo el termostato T9 Wi-Fi Priorice las habitaciones Priorice una o varias habitaciones específicas, o permita que la comodidad lo siga mediante la detección de movimiento incorporada. Control sobre la marcha Ajuste el termostato desde cualquier lugar usando su tablet o teléfono inteligente. Ahorre energía Con la geovalla, puede ahorrar la parte más costosa de su factura de energía mientras se encuentra fuera del hogar. Instalación simple El termostato se programa automáticamente.
Usar su termostato La pantalla se activará cuando presione el área central de la temperatura que se muestra. Temperatura interior Muestra la temperatura interior actual. Prioridad actual Muestra el tipo de prioridad y la cantidad de habitaciones priorizadas. Expanda el alcance de su termostato con sensores inalámbricos para habitación adicionales. Humedad interior Muestra la humedad interior actual. 2 18% 74 Ajustar temperatura Toque las flechas arriba y abajo para configurar su temperatura deseada.
Uso de la prioridad La configuración de prioridades genera una temperatura promedio en el hogar tomando como referencia habitaciones específicas. Esto le permite priorizar la comodidad en los espacios que desee. Habitaciones seleccionadas Las habitaciones que seleccione manualmente crean una temperatura promedio en el hogar. 72 72 72 72 Habitación no seleccionada No contribuirá a la temperatura promedio. Habitación seleccionada Contribuirá a la temperatura promedio.
Solución de problemas Si tiene dificultades con el termostato, intente las siguientes sugerencias. La mayoría de los problemas se puede corregir rápida y fácilmente. La pantalla está en blanco • • • • El sistema de calefacción y refrigeración no responde • • • • • • Revise el disyuntor del circuito y restablezca si es necesario. Asegúrese que el interruptor de alimentación del sistema de calefacción y refrigeración se encuentre encendido.
POLIZA DE GARANTIA IMPORTADO EN MEXICO POR: Instromet Mexicana S. de R.L. de C.V. Avenida Santa Fe 94, Torre A Piso 1, Zedec ED Plaza Santa Fe, Alvaro Obregon, Ciudad de Mexico, CP 01210 01-800-083-5925 Instromet Mexicana S. de R.L. de C.V. garantiza que éste producto está libre de defectos en su mano de obra y materiales contra cualquier defecto de fabricación y funcionamiento, bajo uso normal, por el término de 2 años a partir de la fecha de la compra por el consumidor.
Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422 www.resideo.com ©2018 Resideo Technologies, Inc. Todos los derechos reservados. La marca comercial Honeywell Home se utiliza en virtud de la licencia emitida por Honeywell International Inc.. 33-00421ES—02 M.S. 11-18 Impreso en México 33-00421ES_A.