Installation Instructions RCW35 and RCW25 Series Decorative Wired Chimes RCW250N, RCW251N, RCW35N, RCW3501N, RCW3502N, RCW3503N, RCW3504N, RCW3505N, RCW3506N 69-2173EFS_B.
Installation Instructions Contents Safety.............................................................................................................................................. 3 Checking pack contents................................................................................................................ 4 Installation...................................................................................................................................... 5 Power supply..........................
RCW35 Series and RCW25 Series VOLUME CONTROL CHANNEL INDICATOR LED PROGRAM BUTTON TUNE BUTTON WIRE CONNECTION PORT/TERMINAL LOW BATTERY LED HOLE FOR CABLE/WIRE ENTRY OPTIONAL POWER WITH FOUR x LR14C ALKALINE BATTERIES WIRED CHIME BASE DECORATIVE CHIME COVER SOLD SEPARATELY FROM RCW35N M27274 M27254 69-2173EFS_B.
Installation Instructions Compatible with most bell pushes, with standard normally open contacts, including Honeywell wired pushes marked with “B.” Can work with up to 3 push circuits. Illuminated bell push buttons can be used when the chime is powered by a transformer (Honeywell RCA900N). 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. • Chime is for indoor use only.
Installation Instructions Checking Pack Contents • Chime • 2 x fixing screws for chime • 2 x wall plugs You will need: • Wired push • 20 AWG minimum bell wire • 4 mm cross-head screwdriver • A small flat bladed screwdriver • 1/4-in. (6 mm) masonry drill bit • 4 x LR14 ‘C’ Alkaline batteries OR transformer (16V 10 VA) Honeywell part number RCA900N 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Installation 1. Open the chime cover M27275 69-2173EFS_B.
Installation Instructions Power Supply 2. Determine the type of power supply and type of wired push required to suit your installation. Use 4 x LR14 ‘C’ size alkaline batteries; OR a 16V, 10VA transformer as recommended in the table below below: ATTENTION! ATTENTION! ¡ATENCIÓN! 1 2 3 T 16 V~ M27276 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Mount the Chime 3. Mounting holes are marked with a screw symbol. � 2M 6 FT � M27250 69-2173EFS_B.
Installation Instructions Wiring OPTION 1: AC POWERED DO NOT USE BATTERIES Connect the wires from door push and transformer (where used) to the chime terminals as detailed in step 4. The wires can be surface mounted or direct from opening in the wall and enter the rear of the chime housing using the wire guide channels provided. x1 16V~ x3 120V~ AC V/AC C1 4a. Transformer powered - Wiring for standard/lighted push via a 16V 10VA transformer.
RCW35 Series and RCW25 Series OPTION 2: SERIES AC CONNECTION REQUIRED BATTERIES Note: Wire/cable length should not exceed 150 ft. (50 m). x1 x3 120V~ 16V~ AC V/AC C1 C2 C3 1 16V~ 2 3 120V~ M27280 69-2173EFS_B.
Installation Instructions 4b. Battery powered - Wiring for standard (non-lighted) push only. x1 x3 Note: Wire/cable length should not exceed 150 ft. (50 m). AC V/AC C1 C2 C3 1 2 3 M27281 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Operate Push 5. Chime will play the default tune. The associated channel LED will illuminate. 6. To adjust volume. M27277 11 69-2173EFS_B.
Installation Instructions To Change Tune 7. Chime tunes are provided plus an additional alert tone. Tunes Table Ding Dong St Clements Westminster Tube Chime Warm Brass Fantasy ! 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Press push button, chime will play tune, while the Channel LED on chime is flashing, press and release tune button . Press and release button again to cycle through the available tunes until you hear the tune you want to play. The last tune played will be stored after Channel LED stops flashing. To confirm, press the push button and chime will play tune you want. ! M27278 13 69-2173EFS_B.
Installation Instructions Program Button 8. The Program button can be used to: • Change the tune of the associated push without pressing the push button. Press and hold the program button l. The channel LED will illuminate in sequence. Release the program button when channel LED for the related push illuminates. The chime will play the latest tune, channel LED will flash. While channel LED is flashing, tune can be changed using the tune select button .
RCW35 Series and RCW25 Series 9. Clip on the front cover. 10. For customizable wood covers only: Choose your paint, wood stain/ varnish or wall paper and then apply to the cover. Follow manufacturers’ advice on the paint/vanish. It is possible to unscrew the four screws shown below for finishing. Ensure you screw it back with the same screws provided! Once completed, clip it onto the base. M27251 15 69-2173EFS_B.
Installation Instructions Specification Operating Temperature Sound Level (typical) Power Supply Battery Life (if applicable) (5 operations/day) 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Troubleshooting When the illuminated bell push is operated, very dim / no light appears on the push… Check the power supply. You should use a 16V 10VA transformer connection for an illuminated push. Follow step 4. The chime does not work… • Check that the wiring is done correctly according to step 4, using minimum 20AWG wire. If using batteries: • Check that the batteries are the correct type, LR14 ‘C’ cells. Only use alkaline batteries.
Installation Instructions Disposal & Recycling Batteries and waste electrical products should not be disposed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. Guarantee Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required; this does not affect your statutory rights. If you require further information about your product, call the Honeywell helpline at 1-800-468-1502.
RCW35 Series and RCW25 Series 19 69-2173EFS_B.
Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2008 Honeywell International Inc. 69-2173EFS—03 M.S. Rev. 04-08 69-2173EFS_B.
Installation Directives Instructions d’installation Séries RCW35 et RCW25 (51366SL) Carillons câblés décoratifs RCW250N, RCW251N, RCW35N, RCW3501N, RCW3502N, RCW3503N, RCW3504N, RCW3505N, RCW3506N 69-2173EFS_A.
Directives d’installation Table des matières Sécurité........................................................................................................................................ 25 Vérification du contenu de la boîte............................................................................................. 26 Installation.................................................................................................................................... 27 Alimentation électrique..............
Séries RCW35 et RCW25 RÉGLAGE DU VOLUME INDICATEUR DE VOIE DE TRANSMISSION BOUTON DE PROGRAMMATION BOUTON DE SÉLECTION DES MÉLODIES PORT/BORNE POUR CONNEXION PAR FIL INDICATEUR DE PILES FAIBLES OUVERTURE POUR PASSAGE DU CÂBLE/FIL ALIMENTATION OPTIONNELLE PAR 4 PILES ALCALINES LR14C BASE DE CARILLON CÂBLÉE COUVERCLE DÉCORATIF VENDU SÉPARÉMENT DU RCW35N MF27274 M27254 23 69-2173EFS_B.
Directives d’installation Compatible avec la plupart des sonnettes avec contacts normalement ouverts, y compris les sonnettes câblées marquées «B». Peut prendre en charge jusqu’à trois circuits de sonnette. Les boutons de sonnette lumineux peuvent être utilisés lorsque le carillon est alimenté par un transformateur (Honeywell RCA251N). 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Sécurité Avant de procéder à l’installation, veuillez prendre note des précautions suivantes : • Toujours suivre les directives du fabricant lors de la manipulation d’outils électriques et porter le matériel de protection qui convient (p. ex., lunettes de protection) avant de percer des ouvertures. • Avant de percer des trous dans les murs, vérifier s’il y a des conduites d’eau ou des câbles électriques dissimulés.
Directives d’installation Vérification du contenu de la boîte • Carillon • 2 vis de fixation pour le carillon • 2 chevilles d’ancrage Vous aurez besoin de : • Sonnette à fil • Fil pour sonnette de calibre d’au moins 20 AWG • Tournevis cruciforme de 4 mm • Un petit tournevis à lame plate • Un foret de maçonnerie de 6 mm (1/4 po) • 4 piles alcalines LR14, taille C ou transformateur (16 V 10 VA) Honeywell, numéro de pièce RCA900N 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Installation 1. Retirer le couvercle du carillon M27275 27 69-2173EFS_B.
Directives d’installation Alimentation électrique 2. Déterminer le type d’alimentation électrique et le type de sonnette câblée qui conviennent à l’installation. Installer quatre piles alcalines de type LR4, de taille C ou un transformateur de 16 V, 10 VA, selon les recommandations du tableau ci-dessous. ATTENTION! ATTENTION! ¡ATENCIÓN! 1 2 3 T 16 V~ M27276 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Installation du carillon 3. Les ouvertures de fixation sont indiquées par un symbole représentant une vis. � 2M 6 PI � MF27250 29 69-2173EFS_B.
Directives d’installation Raccordement OPTION 1 : ALIMENTATION CA NE PAS UTILISER DE PILES 16V~ x3 120V~ AC V/AC C1 C2 C3 1 16V~ 4a. Alimentation par transformateur - Câblage pour sonnette standard/lumineuse par l’entremise d’un transformateur 16 V 10 VA. x1 16V~ Raccorder les fils de la sonnette et du transformateur (selon le cas) aux bornes du carillon comme l’indique en détail l’étape 4.
Séries RCW35 et RCW25 OPTION 2 : CONNEXION SÉRIE CA PILES REQUISES Remarque : La longueur du fil/câble ne doit pas dépasser 46 m (150 pi). x1 x3 120V~ 16V~ AC V/AC C1 C2 C3 1 16V~ 2 3 120V~ MF27280 31 69-2173EFS_B.
Directives d’installation 4b. Alimentation par piles - Câblage pour sonnette standard (non lumineuse) seulement. x1 x3 Remarque : La longueur du fil/câble ne doit pas dépasser 46 m (150 pi). AC V/AC C1 C2 C3 1 2 3 M27281 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Faire fonctionner la sonnette 5. Le carillon fait entendre la mélodie par défaut. Le voyant de la voie de transmission associée s’allume. 6. Bouton pour régler le volume. M27277 33 69-2173EFS_B.
Directives d’installation Pour modifier la mélodie 7. Le carillon offre les mélodies suivantes ainsi qu’une tonalité d’alerte. Tableau des mélodies Ding Dong St Clements Westminster Carillon tubulaire Cuivres chaleureux Fantaisie ! 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Appuyer sur la sonnette pour faire entendre la mélodie; pendant que le voyant de la voie de transmission sur le carillon clignote, appuyer sur le bouton de mélodie et le relâcher. Appuyer sur le bouton puis le relâcher à nouveau pour faire entendre l’une après l’autre les mélodies offertes jusqu’à se fasse entendre celle de votre choix. La dernière mélodie entendue sera conservée en mémoire lorsque le voyant de la voie de transmission sera éteint.
Directives d’installation Bouton de programmation 8. Le bouton de programmation peut servir à ce qui suit : • Modifier la mélodie associée à la sonnette sans avoir à appuyer sur la sonnette. Appuyer sur le bouton de programmation l et le maintenir enfoncé. Le voyant de la voie de transmission associée s’allume en séquence. Relâcher le bouton de programmation lorsque le voyant de transmission de la sonnette associée s’allume. Le carillon fait entendre la mélodie la plus récente, et le voyant clignote.
Séries RCW35 et RCW25 9. Remettre le couvercle en place. 10. Dans le cas d’un couvercle en bois pouvant être recouvert, peint ou teint : Choisir une peinture, une teinture, un vernis ou un papier peint et l’appliquer sur le couvercle. Suivre les directives du fabricant de la peinture ou du vernis. Il est possible de dévisser les quatre vis illustrées ci-dessous en prévision de la peinture. S’assurer de remettre les mêmes vis en place. Une fois la peinture terminée, remettre le couvercle sur la base.
Directives d’installation Caractéristiques Température de service Niveau sonore (type) Alimentation électrique Durée de vie des piles (selon le cas) (5 utilisations par jour) 69-2173EFS—03 69-2173EFS_B.
Séries RCW35 et RCW25 Dépannage Lorsqu’on appuie sur la sonnette lumineuse, il y a peu ou pas du tout de lumière sur la sonnette… Vérifier l’alimentation électrique. Une sonnette lumineuse nécessite l’utilisation d’un transformateur 16 V 10 VA. Suivre l’étape 4. Le carillon ne fonctionne pas… • Vérifier si le raccordement est bien fait, comme l’explique l’étape 4, au moyen de fil de calibre d’au moins 20 AWG.
Directives d’installation Mise au rebut et recyclage Les piles et les produits électriques ne doivent pas être mis au rebut avec les ordures ménagères. Prière de recycler partout où les services adéquats sont à disposition. Communiquer avec la municipalité ou le détaillant pour obtenir des conseils en matière de recyclage. Garantie Honeywell garantit ce produit pendant une année à partir de la date d’achat. La preuve d’achat sera exigée sans que cela n’affecte les droits qui vous sont accordés par la loi.
Séries RCW35 et RCW25 41 69-2173EFS_B.
Honeywell International Inc. SRA, Régulateurs d’ambiance et de combustion 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Imprimé aux É.-U. sur du papier recyclé contenant au moins 10 % de fibres de papier recyclées après consommation. ® Marque enregistrée des É.-U. Copyright © 2008 Honeywell International Inc. 69-2173EFS—03 M.S. Rev. 04-08 69-2173EFS_B.
Installation Instrucciones de Instructions Instalación Series RCW35 y RCW25 (51366SL) Campanillas decorativas cableadas RCW250N, RCW251N, RCW35N, RCW3501N, RCW3502N, RCW3503N, RCW3504N, RCW3505N, RCW3506N 69-2173EFS_A.
Instrucciones de Instalación Índice Seguridad..................................................................................................................................... 47 Verificación del contenido del paquete...................................................................................... 48 Instalación.................................................................................................................................... 49 Suministro de energía................................
RCW35 Series and RCW25 Series CONTROL DE VOLUMEN LED INDICADOR DEL CANAL BOTÓN DE PROGRAMACIÓN BOTÓN DE MELODÍA PUERTO/TERMINAL DE CONEXIÓN DE LOS CABLES LED DE BATERÍA BAJA AGUJERO PARA LA ENTRADA DE LOS CABLES ENERGÍA OPCIONAL CON CUATRO BATERÍAS ALCALINAS LR14C BASE DE LA CAMPANILLA CABLEADA LA CUBIERTA DECORATIVA PARA LA CAMPANILLA SE VENDE SEPARADA DEL MODELO RCW35N MS27274 45 69-2173EFS_B.
Instrucciones de Instalación Compatible con la mayoría de los pulsadores de timbre, con contactos normalmente abiertos estándar y con los pulsadores cableados Honeywell con la marca “B”. Puede funcionar hasta con tres circuitos pulsadores. Los botones pulsadores del timbre iluminados pueden utilizarse cuando la campanilla está alimentada por un transformador (Honeywell RCA900N). 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Seguridad Antes de proceder con la instalación, observe las siguientes advertencias de seguridad: • Siempre siga las recomendaciones del fabricante cuando utilice herramientas eléctricas y utilice equipo protector adecuado (por ej.: gafas de seguridad) cuando taladre agujeros, etc. • Antes de taladrar agujeros en las paredes, revise si hay cables eléctricos o tuberías de agua ocultos. El uso de un localizador de cables/tuberías es aconsejable si tiene dudas.
Instrucciones de Instalación Verificación del contenido del paquete • Campanilla • 2 tornillos de fijación para la campanilla • 2 enchufes de pared Necesitará: • Pulsador cableado • Cable para timbre 20 AWG mínimo • Destornillador de cruceta de 4 mm • Un destornillador pequeño de hoja plana • Broca para taladro de mampostería de ¼ pulgadas (6 mm) • 4 baterías alcalinas LR14 “C” O transformador (16 V 10 VA) pieza de Honeywell número RCA900N 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Instalación 1. Abra la cubierta de la campanilla M27275 49 69-2173EFS_B.
Instrucciones de Instalación Suministro de energía 2. Determine el tipo de suministro de energía y el tipo de pulsador cableado requeridos para la instalación. Utilice 4 baterías alcalinas LR14 tamaño “C” O un transformador de 16 V, 10 VA tal como se recomienda en la siguiente tabla: ATTENTION! ATTENTION! ¡ATENCIÓN! 1 2 3 T 16 V~ M27276 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Instale la campanilla 3. Los agujeros de montaje están marcados con el símbolo de un tornillo. � 2M 6 FT � M27250 51 69-2173EFS_B.
Instrucciones de Instalación Cableado 16V~ x3 120V~ AC V/AC C1 1 16V~ 2 3 120V~ 69-2173EFS—03 69-2173EFS_B.indd 52 C2 C3 16V~ 4a. Alimentado por transformador: cableado para pulsador estándar/con luz a través de un transformador de 16 V 10 VA. x1 16V~ Conecte los cables del pulsador de puerta y del transformador (cuando se utilice) en los terminales de la campanilla tal como se detalla en el paso 4.
RCW35 Series and RCW25 Series OPCIÓN 2: LA SERIE CON CONEXIÓN DE CA REQUIERE BATERÍAS Nota: la longitud del cable no debe exceder los 150 pies (46 m). x1 x3 120V~ 16V~ AC V/AC C1 C2 C3 1 16V~ 2 3 120V~ MS27280 53 69-2173EFS_B.
Instrucciones de Instalación 4b. Alimentado por batería: cableado para pulsador (sin luz) estándar únicamente. x1 x3 Note: la longitud del cable no debe exceder los 150 pies (46 m). AC V/AC C1 C2 C3 1 2 3 M27281 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Accione el pulsador 5. La campanilla reproducirá la melodía predeterminada. Se iluminará el LED del canal asociado. 6. Para regular el volumen. M27277 55 69-2173EFS_B.
Instrucciones de Instalación Para cambiar melodías 7. Las melodías de la campanilla además cuentan con un tono de alerta adicional. Tabla de melodías Ding Dong St Clements Westminster Tube Chime Warm Brass Fantasy ! 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Presione el botón pulsador, la campanilla reproducirá la melodía, mientras el LED del canal esté destellando en la campanilla, presione y suelte el botón de melodía . Presione y suelte el botón nuevamente para alternar a través de las melodías disponibles hasta que escuche la melodía que desea reproducir. La última melodía reproducida se almacenará después de que el LED del canal deje de destellar.
Instrucciones de Instalación Botón de programación 8. El botón de programación puede utilizarse para: • Cambiar la melodía del pulsador asociado sin presionar el botón pulsador. Presione y mantenga presionado el botón de programación l. El LED del canal se iluminará en secuencia. Suelte el botón de programación cuando se ilumine el LED del canal del pulsador asociado. La campanilla reproducirá la última melodía, el LED del canal destellará.
RCW35 Series and RCW25 Series 9. Enganche la cubierta frontal. 10. Solo para cubiertas de madera personalizables: Elija la pintura, tinte/ barniz para madera o papel tapiz y luego aplíquelo a la cubierta. Siga las instrucciones del fabricante para aplicar la pintura/barniz. Para realizar el acabado, se pueden desatornillar los cuatro tornillos que se ilustran más abajo. ¡Asegúrese de atornillar nuevamente con los mismos tornillos que se incluyen! Una vez terminado, engánchela a la base.
Instrucciones de Instalación Especificación Temperatura de funcionamiento Nivel de sonido (promedio) Suministro de energía Vida de la batería (si corresponde) (5 activaciones por día) 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series Solución de problemas Cuando se acciona el pulsador del timbre iluminado, la luz no aparece o aparece muy tenue… Verifique el suministro de energía. Debe utilizar una conexión para transformador de 16 V 10 VA para un pulsador iluminado. Siga el paso 4. La campanilla no funciona… • Verifique que el cable esté instalado correctamente, de acuerdo con el paso 4 y con el cable 20 AWG mínimo. Si utiliza baterías: • Verifique que las baterías sean del tipo adecuado, LR14 “C”.
Instrucciones de Instalación Desecho y reciclaje Las baterías y los desechos procedentes de productos eléctricos no deben colocarse con los residuos domésticos. Recicle donde haya tales instalaciones. Verifique con las autoridades locales o el distribuidor la disponibilidad del servicio de reciclaje. Garantía Honeywell garantiza este producto por el lapso de 1 año a partir de la fecha de compra. La prueba de compra es necesaria; esto no afecta sus derechos legales.
RCW35 Series and RCW25 Series 63 69-2173EFS_B.
Instrucciones de Instalación 69-2173EFS—03 69-2173EFS_B.
RCW35 Series and RCW25 Series 65 69-2173EFS_B.
Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Impreso en los EE. UU., en papel reciclado que contiene por lo menos un 10% de fibras de papel reciclable. ® Marca registrada de los EE. UU. © 2008 Honeywell International Inc. 69-2173EFS—03 M.S. Rev. 04-08 69-2173EFS_B.