Installation Instructions RCWL200A and RCWL210A Portable Chime (51375SL; 51376SL) With Push (51381SL) 69-2112EFS-07 69-2112EFS_D.
Installation Instructions LED INDICATES TRANSMITION FLASHING LIGHT (FOR RCWL210A ONLY) PUSH BUTTON VOLUME CONTROL SWITCH M27176 LED PROGRAMMING BUTTON FLASHING LIGHT AND SOUND SELECTION SWITCH (FOR RCWL210A ONLY) 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.
Installation Instructions 2. Installing Batteries CR2032 + CR2032 + M27182 – – 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 3. Change Tune or Program New Push Press and release programming button, LED will illuminate, press push button to hear the tune. Press push button again to hear another tune. To save the tune selected, press and release programming button. M27183 Note: Pressing the program button for more than 15 sec will erase all memory. Follow step 3 to re-program. M27145 3 69-2112EFS_D.
Installation Instructions 4. Install Back Cover Using Screws or Adhesive Pad Provided TOP TOP Note: Before final installation adjust distance and position between push and chime to optimize the chime within your environment. Dense walls and metal can reduce range. M27184 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 5. Volume Adjustment 5 69-2112EFS_D.
Installation Instructions 6. Strobe and Sound Selections Light and sound selection (applicable to RCWL210A only). 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 7. Low Battery Indication Tune + 2 beeps + 2 LED flashes = change batteries in chime. Tune + 3 beeps + 3 LED flashes = change battery in push. – + BEEP 2 + BEEP 3 + x2 + x3 – + – CR2032 + 7 69-2112EFS_D.
Installation Instructions Specification Operating Temperature RF Frequency – US Range (open field) Sound Level (typical) RF Power Battery Type Battery Life (5 operations/day) Water Proof Tunes 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A Troubleshooting Two ‘beep’ sounds are heard and LED flashes twice after the normal chime sound… This indicates a low battery in the chime. Install new batteries, type LR14 C size alkaline batteries. Three ‘beep’ sounds are heard and LED flashes three times after the normal chime sound… This indicates a low battery in the bell push that activated the chime. Install a new battery, type CR2032.
Installation Instructions Troubleshooting The chime does not sound… • Check the chime switch position. • Check that the volume control is not at the minimum setting. Chime does not play tune selected… Chime might not have learned the tune selected. Follow programming sequence as in step 3. The range is reduced… • Metal structures, including uPVC door frames can reduce the range of the product. Avoid mounting the push or chime on or near metal structures.
RCWL200A and RCWL210A Guarantee Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required; this does not affect your statutory rights. If you require further information about your product, call the Honeywell helpline at 1-800-468-1502. Declaration Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards.
Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2009 Honeywell International Inc. 69-2112EFS—07 M.S. Rev. 12-09 69-2112EFS_D.
Directives d’installation RCWL200A et RCWL210A Carillon portatif (51375SL; 51376SL) et sonnette (51381SL) 69-2112EFS_C.
Directives d’installation VOYANT – CONFIRME LA TRANSMISSION DU SIGNAL STROBOSCOPE (RCWL210A SEULEMENT) SONNETTE BOUTON DE RÉGLAGE DU VOLUME MF27176 VOYANT BOUTON DE PROGRAMMATION BOUTON DE SÉLECTION DU SON ET DU STROBOSCOPE (RCWL210 SEULEMENT) 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A Sécurité Avant de commencer l’installation, veuillez respecter les consignes de sécurité suivantes : • Toujours suivre les recommandations du fabricant lorsqu’on utilise des appareils électriques et toujours se servir d’un équipement protecteur (par ex. des lunettes de protection) lorsqu’on perce des trous, etc. • Avant de percer un trou dans un mur, vérifier qu’il n’y a pas de canalisations ou de câbles électriques encastrés.
Directives d’installation 2. Insertion des piles CR2032 + CR2032 + M27182 – – 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 3. Modifier la mélodie ou programmer une nouvelle sonnette Appuyer sur le bouton de programmation et le relâcher; le voyant s’allumera, et il faudra ensuite appuyer sur le bouton de la sonnette pour entendre la mélodie. Appuyer à nouveau sur le bouton de la sonnette pour entendre une autre mélodie. Pour sauvegarder la mélodie sélectionnée appuyer sur le bouton de programmation et le relâcher.
Directives d’installation 4. Installation de la plaque arrière à l’aide de vis ou du tampon adhésif fourni HAUT HAUT Remarque : Avant d’installer la sonnette, ajuster sa position et vérifier la distance entre la sonnette et le carillon pour optimiser le fonctionnement du système. MF27184 Type de mur Réduction de la portée Mur de partition en gypse 10–30 % 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 5. Réglage du volume 19 69-2112EFS_D.
Directives d’installation 6. Sélection du stroboscope et du son Sélection du stroboscope et du son (RCWL210A seulement. M27180 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A 7. Indicateur de piles faibles Mélodie + 2 bips + voyant qui clignote 2 fois = remplacer les piles du carillon. Mélodie + 3 bips + voyant qui clignote 3 fois = remplacer les piles de la sonnette. – + BEEP 2 + BEEP 3 + x2 + x3 – + – CR2032 + 21 69-2112EFS_D.
Directives d’installation Caractéristiques techniques Température de service Fréquence RF - ÉtatsUnis Portée (à ciel ouvert) Niveau sonore (type) Puissance émise Type de pile Durée de vie de la pile (5 déclenchements/jour) Infiltration d’eau Mélodies 69-2112EFS—07 69-2112EFS_D.
RCWL200A and RCWL210A Dépannage Deux bips retentissent et le voyant clignote deux fois après le carillon normal… Ce signal indique que les piles du carillon sont faibles. Installer des piles alcalines neuves de type LR14, de taille C. Trois bips retentissent et le voyant clignote trois fois après le carillon normal… Cela signifie que la pile de la sonnette qui a déclenché le carillon est faible. Installer une nouvelle pile de type CR2032.
Directives d’installation Dépannage Le carillon ne sonne pas… • Vérifier la position de l’interrupteur du carillon. • Vérifier que le volume n’est pas réglé au minimum. Le carillon ne fait pas entendre la mélodie sélectionnée… Le carillon n’a pas appris la mélodie sélectionnée. Suivre les étapes de programmation décrites au numéro 3. La portée est réduite… • Les structures métalliques, notamment les cadres de fenêtre et de porte en PVC-U, peuvent réduire la portée du produit.
RCWL200A and RCWL210A Mise au rebut et recyclage Mise au rebut et recyclage. Prière de recycler partout où les services adéquats existent. Communiquer avec la municipalité ou le détaillant pour obtenir des conseils en matière de recyclage. Déclaration Par la présente, Honeywell déclare que ce carillon sans fil est conforme aux exigen-ces de la partie 15 des règles de la FCC et aux normes d’Industrie Canada.
Garantie Honeywell garantit ce produit pendant une durée de un an à partir de la date d’achat. La preuve d’achat sera exigée sans que cela n’affecte les droits qui vous sont accordés par la loi. Pour obtenir de plus amples informations concernant notre produit, prière de communiquer avec les Services à la clientèle de Honeywell en composant le 1-800-468-1502. Honeywell International Inc. SRA, Régulateurs d’ambiance et de combustion 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.
Instrucciones de Instalación RCWL200A y RCWL210A Campanilla portátil (51375SL; 51376SL) con pulsador (51381SL) 69-2112EFS_C.
Instrucciones de Instalación LUZ ESTROBOSCÓPICA (PARA RCWL210A ÚNICAMENTE) LED – INDICA ACTIVACIÓN DE TRANSMISIÓN BOTÓN PULSADOR INTERRUPTOR DE CONTROL DE VOLUMEN MS27176 LED BOTÓN DE PROGRAMACIÓN LUZ ESTROBOSCÓPICA E INTERRUPTOR DE SELECCIÓN DE SONIDO (PARA RCWL210 ÚNICAMENTE) 69-2112EFS—07 69-2112EFS_D.
RCWL200A y RCWL210A Seguridad Antes de proceder con la instalación, por favor observe las siguientes advertencias sobre seguridad: • Siempre siga las recomendaciones del fabricante cuando utilice herramientas eléctricas y utilice equipo protector adecuado (por ej.: gafas de seguridad) cuando taladre agujeros, etc. • Antes de taladrar agujeros en las paredes, revise si existen cables de electricidad o tuberías de agua ocultos.
Instrucciones de Instalación 2. Instalación de baterías CR2032 + CR2032 + M27182 – – 69-2112EFS—07 69-2112EFS_D.
RCWL200A y RCWL210A 3. Cambie la melodía o programe el pulsador nuevo Presione y suelte el botón de programación, el LED se iluminará, presione el pulsador para escuchar la melodía. Presione el botón pulsador nuevamente para escuchar otra melodía. Para guardar la melodía seleccionada presione y suelte el botón de programación. M27183 Nota: Presionar el botón de programación durante más de 15 segundos borrará toda la memoria. Siga el paso 3 para reprogramar. 31 69-2112EFS_D.
Instrucciones de Instalación 4. Instale la cubierta posterior utilizando tornillos o la almohadilla adhesiva que se suministra PARTE SUPERIOR PARTE SUPERIOR Nota: Antes de la instalación final regule la distancia y la posición entre el pulsador y la campanilla para optimizar la campanilla en su ambiente. Las paredes gruesas y el metal pueden disminuir el alcance.
RCWL200A y RCWL210A 5. Regulación de volumen 33 69-2112EFS_D.
Instrucciones de Instalación 6. Luz estroboscópica y surtido de sonidos Luz y surtido de sonidos (aplica a RCWL210A únicamente). M27180 69-2112EFS—07 69-2112EFS_D.
RCWL200A y RCWL210A 7. Indicación de batería baja Melodía + 2 pitidos + 2 destellos del LED = cambio de baterías en la campanilla. Melodía +3 tonos +3 destellos del LED = cambie las baterías de la campanilla. – + BEEP 2 + BEEP 3 + x2 + x3 + – + – CR2032 + + CR2032 + M27181 35 69-2112EFS_D.
Instrucciones de Instalación Especificación Temperatura de funcionamiento Frecuencia RF – US Alcance (campo abierto) Nivel de sonido (promedio) Potencia RF Tipo de batería Vida de la batería (5 activaciones por día) A prueba de lluvia Melodías 69-2112EFS—07 69-2112EFS_D.
RCWL200A y RCWL210A Localización y solución de problemas Se escuchan dos “tonos” y el LED destella dos veces después del sonido normal de la campanilla... Esto indica batería baja en la campanilla. Instale nuevas baterías, tipo LR14 tamaño C alcalinas. Se escuchan tres “tonos” y el LED destella tres veces después del sonido normal de la campanilla... Esto indica que la batería del pulsador del timbre que activa la campanilla está baja. Coloque una nueva batería tipo CR2032.
Instrucciones de Instalación Localización y solución de problemas La campanilla no suena... • Verifique la posición del interruptor de la campanilla. • Verifique que el control de volumen no esté en la posición mínima. La campanilla no reproduce la melodía seleccionada… La campanilla podría no haber memorizado la melodía seleccionada. Siga la secuencia de programación como en el paso 3. Se ha reducido el alcance...
RCWL200A y RCWL210A Garantía Honeywell garantiza este producto por el lapso de 1 año a partir de la fecha de compra. La prueba de compra es necesaria; esto no afecta sus derechos legales. Si necesita mayor información sobre su producto, llame a la línea de ayuda de Honeywell al 1-800-468-1502. Declaración Honeywell por la presente declara que este producto cumple con la Parte 15 de las regulaciones FCC y las normas industriales de Canadá.
Instrucciones de Instalación 69-2112EFS—07 69-2112EFS_D.
RCWL200A y RCWL210A 41 69-2112EFS_D.
Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Impreso en los EE. UU., en papel reciclado que contiene por lo menos un 10% de fibras de papel reciclable. ® Marca registrada de los EE. UU. © 2009 Honeywell International Inc. 69-2112EFS—07 M.S. Rev. 12-09 69-2112EFS_D.