Operating Manual RTH2300 5+2 Programmable Thermostat 69-2326ES-04
CAUTION: EQUIPMENT DAMAGE HAZARD To prevent possible compressor damage, do not use Cooling mode when the outdoor temperature is below 50°F (10°C). Need Help? For assistance with this product please visit http://DIYthermostats.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502. Read and save these instructions.
Programmable Thermostat RTH2300 Table of contents Overview Appendices Thermostat features ..............................2 Quick start .............................................3 Quick reference to controls ...................4 Quick reference to display.....................5 Battery replacement ........................... 15 In case of difficulty .............................. 16 Customer assistance .......................... 17 One-year limited warranty ..................
Operating Manual About your new thermostat Your new thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.
Programmable Thermostat RTH2300 This thermostat is ready to go Simply perform the three steps below and the thermostat is in operation: Set the clock ................................................................................................ See page 6 Select whether to heat or cool...................................................................... See page 7 Select whether to run the fan continuously or only when needed................
Operating Manual Quick reference to controls Screen Lit for 12 seconds when you press any button. Up/Down buttons Press to adjust temperature. Press to set clock, day or schedule (see pages 6 & 11). System switch (see page 7) • Cool: System is in Cooling mode. • Off: System is off. • Heat: System is in Heating mode. Press to override schedule and hold temperature (see page 13). Fan switch (see page 8) • On: Fan runs continuously. • Auto: Fan runs only when heating or cooling is activated.
Programmable Thermostat RTH2300 Quick reference to display Setpoint indicator Appears when the setpoint temperature is displayed. Temporary schedule override (see page 12) Low-battery warning (see page 15) Permanent schedule override (see page 13) Clock Temperature The ambient (measured) temperature is normally displayed. To view the setpoint temperature, press the Up or Down button once. The setpoint temperature will appear for five seconds.
Operating Manual Set the clock Press the Set button. Set Time will appear on the screen and the time display will flash. Press the Up or Down button to set the time. Press the Set button again. Set Day will flash on the screen. Press the Up or Down button to select the day of the week. Press the Run button to save the changes & exit. (The changes are also saved if you do not press any button for 60 seconds.) NOTE: The clock has lost its settings when the time display flashes.
Programmable Thermostat RTH2300 System switch (Heat/Cool) Use the System switch to place the system in one of the following modes: • Cool: System is in Cooling mode. • Off: System is off. • Heat: System is in Heating mode. CAUTION: EQUIPMENT DAMAGE HAZARD. Do not use Cooling mode when the outdoor temperature is below 50°F (10°C).
Operating Manual Fan switch (Auto/On) Use the Fan switch to select the fan operation. • Auto: The fan runs only when heating or cooling is activated (commonly used setting). • On: The fan runs continuously.
Programmable Thermostat RTH2300 Using the schedule Press the Run button to follow the programmed schedule. For maximum energy savings while maintaining comfort, you can program the schedule such that the temperature is at an economical level when you sleep or leave for work and at a comfortable level when you are awake and at home.
Operating Manual Energy saving default schedule This thermostat is pre-set with energy-saving program settings. See the next page if you wish to modify the settings. Period Wake Weekdays Start time 6:00 AM Heat Weekend Cool Start time 70°F (21°C) 78°F (25.5°C) 6:00 AM Heat Cool 70°F (21°C) 78°F (25.5°C) Leave 8:00 AM 62°F (16.5°C) 85°F (29.5°C) 8:00 AM 62°F (16.5°C) 85°F (29.5°C) Return 6:00 PM 70°F (21°C) 78°F (25.5°C) 6:00 PM 70°F (21°C) 78°F (25.5°C) Sleep 10:00 PM 62°F (16.5°C) 82°F (27.
Programmable Thermostat RTH2300 Modifying the schedule Press the Set button 3 times until Set Schedule appears. The Wake period is displayed. NOTE: To set another period, press the Set button as many times as needed until the desired period and the desired days are displayed and its time or temperature is flashing. When the time flashes, press the Up or Down button to set the time. Wake for the weekdays is set to 6 a.m. and 70°F Press the Set button.
Operating Manual Temporary override of schedule To temporarily ignore the schedule, press the Up or Down button until the desired temperature is displayed. The word Temporary will appear on the screen and the period display will flash to indicate that the current period has been overridden. The new temperature will be used until the next period begins. NOTE: Pressing the Up or Down button once will display the setpoint temperature. To change the setpoint temperature, press either button more than once.
Programmable Thermostat RTH2300 Permanent override of schedule To permanently ignore the schedule, press the Up or Down button until the desired temperature is displayed. Then, press the Hold button to maintain the new temperature indefinitely. The word Hold will appear on the screen. Press the Run button if you wish to cancel the override and resume the schedule. The word Hold will disappear and the thermostat will be set to the temperature programmed for the current period.
Operating Manual Built-in compressor protection Your thermostat has a feature that helps prevent damage to the compressor of your air conditioning or heat pump system. Because damage can occur if the compressor is restarted too soon after shutdown, this feature forces the compressor to wait 5 minutes before restarting. During the wait time, the message Cool On or Heat On flashes on the screen. When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
Programmable Thermostat RTH2300 Battery replacement Set the System switch to Off before removing the batteries. Otherwise, the heating/cooling system could remain activated even when batteries are removed. Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo Batt appears for 60 days before the batteries are depleted. Replace batteries once a year, or when you will be away for more than a month. Most settings are stored in non-volatile (permanent) memory.
Operating Manual In case of difficulty Screen is blank. • Ensure two fresh AAA alkaline batteries are correctly installed. Temperature settings cannot be • The System switch is off. changed. • You are setting the temperature outside its allowable range: • Heat: 40°F to 90°F (4.5°C to 32°C) • Cool: 50°F to 99°F (10°C to 37°C) Cool On or Heat On is flashing. • The compressor protection delay is underway. Wait for the delay to end (maximum of 5 minutes). HI appears on the screen.
Programmable Thermostat RTH2300 Customer assistance For assistance with this product, please visit http://DIYthermostats.honeywell.com. Or call Honeywell Customer Care toll-free at 1-800-468-1502. To save time, before calling, proceed as follows: 1) Loosen the locking screw at the bottom of the thermostat. Note that the screw is captive and cannot be removed from the wallplate. 2) Separate the thermostat from the wallplate as per figure on the right.
Operating Manual One-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
Programmable Thermostat RTH2300 Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited 35 Dynamic Drive Toronto, Ontario M1V 4Z9 http://DIYthermostats.honeywell.com © 2011 Honeywell International Inc. Printed in U.S.A. 69-2326ES-04 M.S. Rev.
Manual del usuario RTH2300 Termostato programable 5+2 69-2326ES-04
ADVERTENCIA: PELIGRO DE DAÑAR EL EQUIPO Para evitar posibles daños en el compresor, el termostato no se debe utilizar en Modo Enfriamiento cuando la temperatura exterior sea inferior a 50°F (10°C). ¿Asistencia? Para obtener asistencia relacionada con este producto, se recomienda visitar http://DIYthermostats.honeywell.com o llamar al número sin cargo del Servicio de Atención al Cliente de Honeywell: 1-800-468-1502.
Termostato programable RTH2300 Índice Generalidades Características del termostato...............2 Puesta en marcha rápida ......................3 Referencia rápida para los controles.....4 Referencia rápida para la pantalla ........5 Apéndices Reemplazo de las pilas ...................... 15 En caso de dificultades....................... 16 Asistencia al cliente ............................ 17 Garantía limitada de un año ............... 18 Programación y funcionamiento Ajuste del reloj..................
Manual del usuario Información sobre el termostato Este nuevo termostato ha sido diseñado para brindar muchos años de funcionamiento fiable y permitir un control climático fácil de usar con sólo apretar un botón. Características • Pantalla con luz de fondo de lectura fácil. • Indica la temperatura ambiente (medida) en todo momento. • Un sólo botón permite ver la temperatura del punto de ajuste. • Configuraciones de ahorro de energía para máximo ahorro de costos.
Termostato programable RTH2300 El termostato está listo para funcionar Basta con llevar a cabo las tres etapas siguientes para poner el termostato en marcha: Ajustar el reloj. .................................................................................................. página 6 Seleccionar calefacción o enfriamiento............................................................. página 7 Seleccionar el modo de funcionamiento del ventilador.....................................
Manual del usuario Referencia rápida para los controles Pantalla Se ilumina durante 12 segundos cuando se oprime un botón Presionar para ajustar el reloj, el día o el horario (ver las páginas 6 y 11) Botones Arriba/Abajo Presionar para ajustar la temperatura Conmutador del sistema (ver la página 7) • Cool: Modo Enfriamiento.
Termostato programable RTH2300 Referencia rápida para la pantalla Indicador de punto de ajuste Aparece cuando se visualiza el punto de ajuste de la temperatura Cancelación temporaria del horario (ver la página 12) Indicador de pilas débiles (ver la página 15) Cancelación permanente del horario (ver la página 13) Reloj Temperatura Indica normalmente la temperatura ambiente (medida). Para ver la temperatura del punto de ajuste, presionar el botón Arriba o Abajo una vez.
Manual del usuario Ajuste del reloj Presionar el botón Set. En la pantalla aparecerá Set Time y la hora parpadeará. Presionar el botón Arriba o Abajo para ajustar la hora. Presionar el botón Set otra vez. En la pantalla parpadeará Set Day. Presionar el botón Arriba o Abajo para elegir el día de la semana. Presionar el botón Run para salvaguardar los cambios y salir. (Las modificaciones se salvaguardan también si no se presiona ningún botón durante 60 segundos).
Termostato programable RTH2300 Conmutador del sistema (Calefacción/Enfriamiento) Utilizar el conmutador del sistema (System) para poner el termostato en uno de los modos siguientes: • Cool: el sistema está en Modo Enfriamiento • Off: el sistema está apagado • Heat: el sistema está en Modo Calefacción ADVERTENCIA: PELIGRO DE DAÑAR EL EQUIPO No se debe usar el Modo Enfriamiento cuando la temperatura exterior es inferior a 10°C (50°F).
Manual del usuario Conmutador del ventilador (Auto/On) Usar el conmutador del ventilador (Fan) para escoger el funcionamiento del ventilador. • Auto: el ventilador funciona únicamente cuando la calefacción o el enfriamiento están en marcha (ajuste más común). • On: el ventilador funciona continuamente.
Termostato programable RTH2300 Uso del horario Presionar el botón Run para seguir el horario programado. Para obtener una economía máxima conservando el confort, se puede programar el horario de manera que la temperatura esté en un nivel de Economía durante la noche y en un nivel confortable cuando los moradores están activos en casa.
Manual del usuario Programación predeterminada para ahorro de energía Este termostato viene predeterminado con configuraciones para un programa de ahorro de energía. Referirse a la página siguiente si se desea modificarlos. Días de semana Período Inicio Despertar 6:00 AM Calefacción Fin de semana Enfriamiento Comienzo 70°F (21°C) 78°F (25.5°C) 6:00 AM Calefacción Enfriamiento 70°F (21°C) 78°F (25.5°C) Salir 8:00 AM 62°F (16.5°C) 85°F (29.5°C) 8:00 AM 62°F (16.5°C) 85°F (29.
Termostato programable RTH2300 Modificación del horario Presionar el botón Set 3 veces hasta que aparezca Set Schedule. La hora de inicio de Despertar para los días de semana (lunes a viernes) parpadeará. Presionar el botón Up o Down para fijar la hora. Presionar el botón Up o Down para ajustar la temperatura. Presionar el botón Set. El ajuste de temperatura para el período parpadeará.
Manual del usuario Cancelación temporaria del horario Para ignorar temporariamente el horario, presionar el botón Arriba o Abajo hasta que la temperatura deseada aparezca en pantalla. Aparecerá el mensaje Temporary y el período en curso parpadeará en la pantalla para indicar que ha sido cancelado. La nueva temperatura estará vigente hasta que comience el próximo período. NOTA: presionando los botones Arriba o Abajo una vez se visualizará el punto de ajuste de la temperatura.
Termostato programable RTH2300 Cancelación permanente del horario Para cancelar el horario de manera permanente, presionar los botones Arriba o Abajo hasta que aparezca en pantalla la temperatura deseada. Presionar entonces el botón Hold para mantener la nueva temperatura de manera indefinida. La palabra Hold aparecerá en la pantalla. Presionar el botón Run si se desea anular la cancelación y retomar el horario.
Manual del usuario Protección del compresor incorporada El termostato tiene una función que protege el compresor del acondicionador de aire o del sistema de bomba de calor. El compresor puede dañarse si vuelve a encenderse inmediatamente después de apagarse. Esta función lo fuerza a esperar 5 minutos antes de volver a entrar en funcionamiento. Durante este tiempo, en la pantalla parpadeará el mensaje de Cool On o Heat On.
Termostato programable RTH2300 Reemplazo de las pilas Poner el conmutador System en OFF antes de retirar las pilas. De lo contrario, el sistema de calefacción/enfriamiento puede permanecer activado aun cuando se hayan sacado las baterías. Instalar dos pilas AAA nuevas cuando Lo Batt parpadee en la pantalla. Lo Batt aparecerá 60 días antes de que las pilas estén completamente descargadas. Reemplazar las pilas una vez por año o luego de una ausencia de más de un mes.
Manual del usuario En caso de dificultades No aparece nada en la pantalla. • Verificar que las dos pilas AAA estén cargadas y correctamente instaladas. No puede modificarse la temperatura. • El conmutador del sistema está apagado (Off). • La temperatura está fuera del margen permitido: • Calefacción: 40 °F a 90 °F (4,5 °C a 32 °C) • Enfriamiento: 50 °F a 99 °F (10 °C a 37 °C) Cool On o Heat On parpadean.
Termostato programable RTH2300 Asistencia al cliente Para obtener asistencia con este producto, se recomienda visitar el sitio http://DIYthermostats.honeywell.com o llamar al Servicio de Asistencia al Cliente de Honeywell al número sin cargo 1-800-468-1502. Para ahorrar tiempo, proceder de la siguiente manera antes de llamar: 1) Aflojar el tornillo en la base del termostato. El tornillo está cautivo y no se podrá retirar de la placa mural.
Manual del usuario Garantía limitada de un año Honeywell garantiza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricación o de los materiales, a partir de la fecha de compra por parte del consumidor, en condiciones normales de uso y servicio. Si en cualquier momento durante el período de garantía se verifica que el producto tiene un defecto o mal funcionamiento, Honeywell lo reparará o reemplazará (a elección de Honeywell).
Termostato programable RTH2300 La única responsabilidad de Honeywell será reparar o reemplazar el producto dentro de los plazos establecidos anteriormente. HONEYWELL NO RESPONDERÁ POR LA PÉRDIDA O DAÑO DE NINGÚN TIPO, INCLUIDO EL DAÑO INCIDENTAL O INDIRECTO DERIVADO, DIRECTA O INDIRECTAMENTE, DEL INCUMPLIMIENTO DE LAS GARANTÍAS, EXPRESAS O IMPLÍCITAS, O DE OTRAS FALLAS DE ESTE PRODUCTO.
. Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited 35 Dynamic Drive Toronto, Ontario M1V 4Z9 http://DIYthermostats.honeywell.com © 2011, Honeywell International Inc. Impreso en EE.UU. 69-2326ES-04 M.S. Rev.