Quick Installation Guide RTH2510/RTH2410 Series Programmable Thermostat 69-2726ES-01
Identify System Type This thermostat is compatible with the following systems: Gas, oil or electric furnace Central air conditioner Hot water system with or without pump Millivolt system Central heating and cooling system Heat pump without auxiliary/backup heat Heat pump with auxiliary/backup heat Do you need assistance? We are here to help. Call 1-800-468-1502 for wiring assistance before returning the thermostat to the store. This thermostat cannot be used on multistage systems.
1 Turn Off Power to Heating/ Cooling System OFF or 1 69-2726ES—01
2 Remove Old Thermostat Remove old thermostat but leave wallplate with wires attached. Do not remove wallplate yet Is there a sealed tube containing mercury? If so, see back cover for proper disposal instructions. EM. HEAT AUX. HEAT 50 60 70 80 50 60 70 80 F Old thermostat EM.
3 Label Wires with Tags Label the wires using the supplied wire labels as you disconnect them.
4 Separate Wallplate from New Thermostat Remove wallplate from the new thermostat and mount onto wall.
5 Mount Wallplate Mount the new wallplate using the included screws and anchors. W/ Aux Not Used M32714 Drill 3/16-in. holes for drywall Drill 3/32-in.
6 Connect Wires Simply match wire labels. WIRE HOLE G INSERT WIRES AND TIGHTEN SCREWS R Y W SCREW W/ Aux LABELED WIRES Not Used M32715 Remove metal jumper if you have both R and Rc wires. Labels don’t match? See page 22. Have a Heat Pump system? See page 23. We are here to help. Call 1-800-468-1502 for wiring assistance.
7 Install Batteries Install two AAA alkaline batteries.
8 Set fan operation switch Move the switch to the proper setting: Gas or Oil: For gas or oil heating systems, leave the fan operation switch in this factory-set position (for systems that control the fan in a call for heat). Electric or Heat Pump: Change the switch to this setting for heat pump or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal.
9 Install Thermostat onto Wallplate Install thermostat onto the wallplate on the wall.
10 Turn Power Back On Turn the power back on to the heating/cooling system.
11 If your system type is... If your system type is: q Single Stage Heat and Cool q Heat Only or Cool Only Congratulations, you’re done! If your system type is: q Heat Pump* with Backup Heat Continue with advanced installation on next page to match your thermostat to your system type. *Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.
Advanced Installation Enter system setup...............................................................13 Changing settings.................................................................14 System type..........................................................................15 Heating cycle rate.................................................................16 Early start.............................................................................17 Temperature display.....................................
RTH2510/RTH2410 System setup Enter System Setup SETUP To enter system setup, press and hold both the s and t buttons until the display changes (approximately 5 seconds).
Advanced Installation Guide SETUP System setup Changing Settings See pages 15–21 to change Function Settings. Function Set WIRING Hold Run 1 0 M33594 Change Function ASSISTANCE Setting Change Setting 1. Press the s or t button to change the setting. 2. Press the s and t buttons simultaneously for one second to advance to the next function. TROUBLESHOOTING 3. Press the Run button to exit and save settings.
RTH2510/RTH2410 System setup Function 1: System Type SETUP 1 0 M32718 Press the s or t button to select the type of Heat/Cool system you have in your home. When finished, press s and t to advance to the next function. AND M33591 15 69-2726ES—01 TROUBLESHOOTING OR Press to change setting. ASSISTANCE 1 Heat pump with auxiliary/backup heat: Outside compressor provides both heating and cooling.
Advanced Installation Guide System setup SETUP Function 5: Heating cycle rate WIRING 5 5 M32720 ASSISTANCE 5 Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient. 6 Electric furnace: Use this setting if you have any type of electric heating system. 3 Hot water or high-efficiency furnace: Use this setting if you have a hot water system or a gas furnace of greater than 90% efficiency.
RTH2510/RTH2410 System setup Function 13: Early Start SETUP 13 1 WIRING M32721 1 On 0 Off OR Press to change setting. When finished, press s and t to advance to the next function. AND M33591 17 69-2726ES—01 TROUBLESHOOTING Press the s or t button to select Early Start. ASSISTANCE Early start allows the heating or cooling to turn on before the program start time, so the temperature is reached at the time you set. Simply program the desired times and temperature into the schedule.
Advanced Installation Guide System setup SETUP Function 14: Temperature display 14 0 WIRING M32722 0 Fahrenheit temperature display (°F) TROUBLESHOOTING ASSISTANCE 1 Celsius temperature display (°C) Press the s or t button to select Fahrenheit or Celsius temperature display. OR Press to change setting. When finished, press s and t to advance to the next function.
RTH2510/RTH2410 System setup Function 15: Compressor Protection SETUP 15 1 M32723 WIRING 1 On 0 Off OR Press to change setting. When finished, press s and t to advance to the next function. AND M33591 19 69-2726ES—01 TROUBLESHOOTING Press the s or t button to select Compressor Protection settings. ASSISTANCE Compressor Protection: This feature forces the compressor to wait approximately 5 minutes before restarting, to prevent equipment damage.
Advanced Installation Guide System setup SETUP Function 20: Clock Display 20 0 WIRING M32724 0 12-hour display TROUBLESHOOTING ASSISTANCE 1 24-hour display Press the s or t button to select clock display. OR Press to change setting. When finished, press s and t to advance to the next function.
RTH2510/RTH2410 System setup Function 21: Change Filter Timer SETUP 21 0 M33631 WIRING 0 Off 1 30 days 2 90 days ASSISTANCE 3 6 months 4 9 months 5 1 year OR Press to change setting. When finished, press s and t to advance to the next function. AND M33591 21 69-2726ES—01 TROUBLESHOOTING Press the s or t button to select Change Filter Timer.
Advanced Installation Guide System setup SETUP Function 40: Restore Program Schedule to Default 40 0 WIRING M32725 0 Off TROUBLESHOOTING ASSISTANCE 1 On - Program schedule default settings are listed in the operating manual. Press the s or t button to select restore program schedule to default settings. OR Press to change setting. When finished, press Run to exit and save changes.
RTH2510/RTH2410 About your new thermostat Wiring—Conventional System 4 4 SETUP If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (see notes, below). WIRING O G Y W/ NOT R AUX USED Rc M32726 If wires will be connected to both R and Rc terminals, remove metal jumper (see page 6). Do not use C or X. Wrap bare end of wire with electrical tape.
Advanced Installation Guide About your new Wiring—Heat Pump thermostat SETUP Connect wires: Heat Pump 1. Match each labeled wire with same letter on new thermostat. 2. Use a screwdriver to loosen screws, insert wires into hole under screw, then tighten screws until wire is secure. TROUBLESHOOTING ASSISTANCE WIRING 3. Push any excess wire back into the wall opening. O G Y Aux B O G Y W/ AUX R R Rc M32727 Labels don’t match? See page 24. Wiring complete, return to Step 7.
RTH2510/RTH2410 About your new Wiring—Heat Pump thermostat If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (see notes, below). 1 4 7 5 3 L E C B F X X2 O G H X B Y F O G Y1 M Y R AUX W W1 W2 NOT W/ AUX USED RC V VR R Rc 2 M32728 ASSISTANCE B 2 7 WIRING 6 SETUP Alternate wiring (for heat pumps with auxiliary or backup heat only) Leave metal jumper in place, connecting R & Rc terminals.
Advanced Installation Guide TROUBLESHOOTING ASSISTANCE WIRING SETUP Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • Make sure furnace door is closed securely. • Make sure fresh AAA alkaline batteries are correctly installed (see page 7). Heating or • Set System switch to Heat. Make cooling system sure the temperature is set higher does not than the Inside temperature.
RTH2510/RTH2410 Troubleshooting “Heat On” is not displayed • Set the System switch to Heat, and set the temperature level above the current room temperature. “Cool On” is not displayed • Set the System switch to Cool, and set the temperature level below the current room temperature. ASSISTANCE • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www.thermostat-recycle.org or 800238-8192 for information on how and where to properly and safely dispose of your old thermostat. CAUTION: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C). Automation and Control Solutions Honeywell International Inc.
Guía de instalación rápida Serie RTH2510/RTH2410 Termostato programable 69-2726ES-01
Identifique el tipo de sistema Este termostato es compatible con los siguientes sistemas: Calefactor a gas, aceite o eléctrico Aire acondicionado central Sistema a agua caliente con o sin bomba Sistema de milivoltios Calefacción y aire acondicionado centrales Bomba de calor sin calefacción auxiliar Bomba de calor con calefacción auxiliar ¿Necesita ayuda? ¡Aquí estamos! Llame al 1-800-468-1502 para obtener asistencia con el cableado antes de devolver el termostato a la tienda.
1 Desconecte la alimentación en el sistema de calefacción/ refrigeración APAGADO o 1 69-2726ES—01
2 Remueva su viejo termostato Retire el termostato existente pero deje la placa de montaje con los cables adheridos. No retirar la placa mural todavía ¿Hay un tubo sellado que contiene mercurio? Si es así, consulte en la cubierta de este manual las instrucciones para su desecho apropiado. EM. HEAT AUX. HEAT 50 60 70 80 50 60 70 80 F Termostato viejo EM.
3 Identifique los cables Identifique los cables a medida que los desconecta, utilizando las etiquetas que se suministran.
4 Separe la placa de montaje del termostato nuevo Retire la placa de montaje del termostato nuevo y móntela en la pared.
5 Coloque la placa de montaje Monte la nueva placa de montaje utilizando los tornillos y anclajes que se suministran. W/ Aux Not Used M32714 Taladre agujeros de 3/32 in. (2,4 mm) en yeso Taladre agujeros de 3/16 in.
6 Conecte los cables Simplemente haga corresponder las etiquetas de los cables. ORIFICIO DE CABLEADO G INSERTE LOS CABLES YAPRIETE LOS TORNILLOS TORNILLO R Y W W/ Aux CABLES ETIQUETADOS Not Used MS32715 Retire el empalme metálico si tiene los cables “R” y “Rc”. ¿Los rótulos no coinciden? Vea la página 22. ¿Tiene un sistema de bomba de calor? Ver página 23. Estamos aquí para ayudarle. Llame al 1-800-468-1502 para asistencia con el cableado.
7 Instale las baterías Instale dos baterías alcalinas AAA.
8 Configure el interruptor de funcionamiento del ventilador Mueva el interruptor a la configuración adecuada: Gas o aceite: para los sistemas de calefacción de gas o aceite, deje el interruptor del ventilador en esta posición configurada de fábrica (para sistemas que controlan el ventilador en una orden de calefacción). Eléctrico o bomba de calor: cambie el interruptor a esta configuración para sistemas de bomba de calor o de calefacción eléctrica.
9 Instale el termostato en la placa de montaje Instale el termostato en la placa de montaje en la pared.
10 Active nuevamente el suministro eléctrico Active nuevamente el suministro eléctrico del sistema de calefacción/aire acondicionado.
11 Si su tipo de sistema es... Si su tipo de sistema es: q Calor y frío de una sola etapa q Calefacción únicamente o Refrigeración únicamente ¡Felicitaciones, ya está listo! Si su tipo de sistema es: q Bomba de calor* con calor de respaldo Continúe con la instalación avanzada en la próxima página para adaptar el termostato a su tipo de sistema. *Bomba de calor —un acondicionador de aire que proporciona enfriamiento en el verano y también funciona en reversa en el invierno, proporcionando calor.
Guía de instalación avanzada Ingrese la configuración del sistema....................................13 Cómo cambiar la configuración............................................14 Tipo de sistema....................................................................15 Frecuencia del ciclo de calefacción......................................16 Encendido anticipado...........................................................17 Indicador de temperatura.....................................................
RTH2510/RTH2410 Configuración del sistema Para ingresar la configuración del sistema, presione y mantenga presionados los botones s (arriba) y t (abajo) hasta que el visualizador cambie (5 segundos aproximadamente).
Guía de instalación avanzada CONFIGURACIÓN Configuración del sistema Cómo cambiar la configuración Consulte las páginas 15-21 para cambiar la configuración de las funciones. WIRING Set ASSISTANCE Configuración Función Hold Run 1 0 M33594 Cambio de función Cambio de configuración 1. Presionar s o t para cambiar la configuración. 2. Presionar s y t al mismo tiempo por un segundo para ir a la función siguiente. TROUBLESHOOTING 3. Presione el botón Run para salir y guardar los cambios.
RTH2510/RTH2410 Configuración del sistema CONFIGURACIÓN Función 1: Tipo de sistema 1 0 M32718 Presione el botón s o t para elegir el tipo de sistema de calefacción/refrigeración que tenga en su hogar. Cuando termine, presione s y t para avanzar hasta la siguiente función. Y MS33591 15 69-2726ES—01 TROUBLESHOOTING O Presione para cambiar la configuración ASSISTANCE 1 Bomba de calor con calefacción auxiliar/de reserva: el compresor externo proporciona tanto calefacción como refrigeración.
Guía de instalación avanzada CONFIGURACIÓN Configuración del sistema About your new thermostat Función 5: Frecuencia del ciclo de calefacción 5 5 TROUBLESHOOTING ASSISTANCE WIRING M32720 5 Sistema de calefacción de gas o aceite: utilice esta configuración si tiene un sistema de calefacción estándar de gas o aceite cuyo rendimiento sea inferior al 90%. 6 Sistema de calefacción eléctrico: utilice esta configuración si tiene cualquier tipo de sistema de calefacción eléctrica.
RTH2510/RTH2410 Configuración del sistema About your new thermostat CONFIGURACIÓN Función 13: Encendido anticipado 13 1 M32721 WIRING 1 Encendido 0 Apagado O Presione para cambiar la configuración Cuando termine, presione s y t para avanzar hasta la siguiente función. Y MS33591 17 69-2726ES—01 TROUBLESHOOTING Presione los botones s o t para seleccionar Encendido anticipado.
Guía de instalación avanzada CONFIGURACIÓN Configuración del sistema Función 14: Indicador de temperatura 14 0 WIRING M32722 0 Indicador de temperatura en grados Fahrenheit (°F) TROUBLESHOOTING ASSISTANCE 1 Indicador de temperatura en grados Centígrados (°C) Presione el botón s or t para elegir el indicador de temperatura en grados Fahrenheit o Centígrados. O Presione para cambiar la configuración Cuando termine, presione s y t para avanzar hasta la siguiente función.
RTH2510/RTH2410 Configuración del sistema 15 1 CONFIGURACIÓN Función 15: Protección del compresor M32723 WIRING 1 Encendido 0 Apagado O Presione para cambiar la configuración Cuando termine, presione s y t para avanzar hasta la siguiente función. Y MS33591 19 69-2726ES—01 TROUBLESHOOTING Presione el botón s or t para elegir la configuración de protección del compresor.
Guía de instalación avanzada CONFIGURACIÓN Configuración del sistema Función 20: Visualizador del reloj 20 0 WIRING M32724 0 Visualizador de 12 horas TROUBLESHOOTING ASSISTANCE 1 Visualizador de 24 horas Presione el botón s or t para elegir el visualizador del reloj. O Presione para cambiar la configuración Cuando termine, presione s y t para avanzar hasta la siguiente función.
RTH2510/RTH2410 Configuración del sistema 21 0 CONFIGURACIÓN Función 21: Cambie el temporizador del filtro M33631 WIRING 0 Apagado 1 30 días 2 90 días ASSISTANCE 3 6 meses 4 9 meses 5 1 año O Presione para cambiar la configuración Cuando termine, presione s y t para avanzar hasta la siguiente función. Y MS33591 21 69-2726ES—01 TROUBLESHOOTING Presione el botón s or t para seleccionar Change Filter Timer (Cambio del temporizador del filtro).
Guía de instalación avanzada CONFIGURACIÓN About your new Configuración del thermostat sistema Función 40: Restablecimiento del cronograma del programa a la configuración predeterminada 40 0 WIRING M32725 0 Apagado TROUBLESHOOTING ASSISTANCE 1 Encendido - Las configuraciones predeterminadas del cronograma del programa se indican en el manual de funcionamiento. Presione el botón s or t para restituir las configuraciones predeterminadas del cronograma del programa.
RTH2510/RTH2410 About your new thermostat Cableado—Sistema convencional 4 SETUP Si las etiquetas no corresponden con las letras del termostato, revise la tabla que sigue y conecte al terminal como se indica aquí (refiérase a las notas que siguen). 4 CABLEADO No Conecte O G Y W/ NOT R AUX USED Rc MS32726 Si los cables se conectarán a los terminales R y Rc, retire el puente metálico (refiérase a la Page 6). ASSISTANCE B No utilice C o X.
Guía de instalación avanzada About your new thermostat Cableado—bomba de calor SETUP Conecte los cables: Bomba de calor 1. Coordine cada cable etiquetado con la misma letra del termostato nuevo. 2. Con un destornillador afloje los tornillos de los terminales, inserte los cables, luego ajuste los tornillos. TROUBLESHOOTING ASSISTANCE CABLEADO 3. Introduzca el excedente de cable en la abertura de la pared. O G Y Aux B O G Y W/ AUX R R Rc M32727 ¿Los rótulos no coinciden? Consulte la página 24.
RTH2510/RTH2410 About your new thermostat Cableado—bomba de calor Cableado alternativo (para bombas de calor con calefacción auxiliar o de reserva únicamente) 1 4 7 5 3 L E C B F X X2 O G H X B Y F Y1 M 7 2 AUX R W W1 W2 CABLEADO 6 RC V VR No Conecte O G Y NOT W/ AUX USED R Rc 2 MS32728 Deje el empalme en lugar, entre terminales de R y Rc.
Guía de instalación avanzada EN CASO DE DIFICULTADES ASSISTANCE WIRING SETUP Assistance En caso de à dificultades la clientèle Si usted tiene dificultades con su termostato, pruebe las sugerencias que figuran a continuación. La mayoría de los problemas se pueden solucionar rápida y fácilmente. Pantalla en blanco • Asegúrese de que la puerta del sistema de calefacción esté bien cerrada. • Asegúrese de que las baterías AAA alcalinas estén instaladas correctamente (vea la página 7).
RTH2510/RTH2410 Assistance la clientèle En caso de à dificultades Asegúrese de que las temperaturas de calor y frío estén configuradas en rangos aceptables: • “Heat”: De 40 °F a 90 °F (de 4,5 °C a 32 °C). • “Cool”: De 50 °F a 99 °F (de 10 °C a 37 °C). • Mueva el interruptor “System” hasta la posición “Heat” y configure el nivel de temperatura por encima de la temperatura ambiente actual.
AVISO DE MERCURIO: No arroje su viejo termostato a la basura si contiene mercurio en un tubo sellado. Comuníquese con Thermostat Recycling Corporation en www.thermostatrecycle.org o llame al 800-238-8192 para obtener información sobre cómo y dónde desechar de forma adecuada y segura su termostato usado. PRECAUCIÓN: Para evitar posibles daños al compresor, no utilice el aire acondicionado si la temperatura externa es inferior a 50ºF (10ºC). Automatización y control desenlace Honeywell International Inc.