Quick Installation Guide RTH2510/RTH2410 Series Programmable Thermostat 69-2602EF-01
Identify System Type This thermostat is compatible with the following systems: Gas, oil or electric furnace Central air conditioner Hot water system with or without pump Millivolt system Central heating and cooling system Heat pump without auxiliary/backup heat Heat pump with auxiliary/backup heat Do you need assistance? We are here to help. Call 1-800-468-1502 for wiring assistance before returning the thermostat to the store. This thermostat cannot be used on multistage systems.
1 Turn Off Power to Heating/ Cooling System M28097 1 69-2602EF—01
2 Remove Old Thermostat Remove old thermostat but leave wallplate with wires attached. Do not remove wallplate yet Is there a sealed tube containing mercury? If so, see back cover for proper disposal instructions.
3 Label Wires with Tags Label the wires using the supplied wire labels as you disconnect them.
4 Separate Wallplate from New Thermostat Remove wallplate from the new thermostat and mount onto wall.
5 Mount Wallplate Mount the new wallplate using the included screws and anchors. W/ Aux Not Used M32714 Drill 3/16-in. holes for drywall Drill 3/32-in.
6 Connect Wires Simply match wire labels. WIRE HOLE G INSERT WIRES AND TIGHTEN SCREWS R Y W SCREW W/ Aux LABELED WIRES Not Used M32715 Remove metal jumper if you have both R and Rc wires. Labels don’t match? See page 22. Have a Heat Pump system? See page 23. We are here to help. Call 1-800-468-1502 for wiring assistance.
7 Install Batteries Install two AAA alkaline batteries.
8 Set fan operation switch Move the switch to the proper setting: Gas or Oil: For gas or oil heating systems, leave the fan operation switch in this factory-set position (for systems that control the fan in a call for heat). Electric or Heat Pump: Change the switch to this setting for heat pump or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal.
9 Install Thermostat onto Wallplate Install thermostat onto the wallplate on the wall.
10 Turn Power Back On Turn the power back on to the heating/cooling system.
11 If your system type is... If your system type is: q Single Stage Heat and Cool q Heat Only or Cool Only Congratulations, you’re done! If your system type is: q Heat Pump* with Backup Heat Continue with advanced installation on next page to match your thermostat to your system type. *Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.
Advanced Installation Enter system setup...............................................................13 Changing settings.................................................................14 System type..........................................................................15 Heating cycle rate.................................................................16 Early start.............................................................................17 Temperature display.....................................
RTH2510/RTH2410 System setup Enter System Setup SETUP To enter system setup, press and hold both the s and t buttons until the display changes (approximately 5 seconds).
Advanced Installation Guide Changing Settings See pages 15–21 to change Function Settings. Function 0 M32717 Change Function ASSISTANCE Setting 1 WIRING SETUP System setup Change Setting 1. Press the s or t button to change the setting. 2. Press the s and t buttons simultaneously for one second to advance to the next function. TROUBLESHOOTING 3. Press the Run button to exit and save settings.
RTH2510/RTH2410 System setup Function 1: System Type SETUP 1 0 M32718 Press the s or t button to select the type of Heat/Cool system you have in your home. When finished, press s and t to advance to the next function. AND M32719 15 69-2602EF—01 TROUBLESHOOTING OR Press to change setting. ASSISTANCE 1 Heat pump with auxiliary/backup heat: Outside compressor provides both heating and cooling.
Advanced Installation Guide System setup SETUP Function 5: Heating cycle rate WIRING 5 5 M32720 ASSISTANCE 5 Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient. 6 Electric furnace: Use this setting if you have any type of electric heating system. 3 Hot water or high-efficiency furnace: Use this setting if you have a hot water system or a gas furnace of greater than 90% efficiency.
RTH2510/RTH2410 System setup Function 13: Early Start SETUP 13 1 WIRING M32721 1 On 0 Off OR Press to change setting. When finished, press s and t to advance to the next function. AND M32719 17 69-2602EF—01 TROUBLESHOOTING Press the s or t button to select Early Start. ASSISTANCE Early start allows the heating or cooling to turn on before the program start time, so the temperature is reached at the time you set. Simply program the desired times and temperature into the schedule.
Advanced Installation Guide System setup SETUP Function 14: Temperature display 14 0 WIRING M32722 0 Fahrenheit temperature display (°F) TROUBLESHOOTING ASSISTANCE 1 Celsius temperature display (°C) Press the s or t button to select Fahrenheit or Celsius temperature display. OR Press to change setting. When finished, press s and t to advance to the next function.
RTH2510/RTH2410 System setup Function 15: Compressor Protection SETUP 15 1 M32723 WIRING 1 On 0 Off OR Press to change setting. When finished, press s and t to advance to the next function. AND M32719 19 69-2602EF—01 TROUBLESHOOTING Press the s or t button to select Compressor Protection settings. ASSISTANCE Compressor Protection: This feature forces the compressor to wait approximately 5 minutes before restarting, to prevent equipment damage.
Advanced Installation Guide System setup SETUP Function 20: Clock Display 20 0 WIRING M32724 0 12-hour display TROUBLESHOOTING ASSISTANCE 1 24-hour display Press the s or t button to select clock display. OR Press to change setting. When finished, press s and t to advance to the next function.
RTH2510/RTH2410 System setup Function 40: Restore Program Schedule to Default SETUP 40 0 M32725 WIRING 0 Off 1 On - Program schedule default settings are listed in the operating manual. ASSISTANCE OR Press to change setting. When finished, press Run to exit and save changes. M32729 21 69-2602EF—01 TROUBLESHOOTING Press the s or t button to select restore program schedule to default settings.
Advanced Installation Guide If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (see notes, below). 4 4 TROUBLESHOOTING ASSISTANCE WIRING SETUP About your new thermostat Wiring—Conventional System B O G Y W/ NOT R AUX USED Rc M32726 If wires will be connected to both R and Rc terminals, remove metal jumper (see page 6). Do not use C or X. Wrap bare end of wire with electrical tape.
RTH2510/RTH2410 Wiring—Heat Pump Connect wires: Heat Pump 2. Use a screwdriver to loosen screws, insert wires into hole under screw, then tighten screws until wire is secure. SETUP 1. Match each labeled wire with same letter on new thermostat. 3. Push any excess wire back into the wall opening. WIRING G Y Aux Y W/ AUX R R Rc M32727 Labels don’t match? See page 24. Wiring complete, return to Step 7.
Advanced Installation Guide SETUP Wiring—Heat Pump Alternate wiring (for heat pumps with auxiliary or backup heat only) If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (see notes, below). 1 7 5 3 L E C B F ASSISTANCE WIRING 4 6 X X2 O G H X B B 2 7 Y F O G Y1 M Y R AUX W W1 W2 NOT W/ AUX USED RC V VR R Rc 2 M32728 Leave metal jumper in place, connecting R & Rc terminals.
RTH2510/RTH2410 Troubleshooting Display is blank • Make sure furnace door is closed securely. • Make sure fresh AAA alkaline batteries are correctly installed (see page 7). • Make sure heating & cooling power switches are on. 25 69-2602EF—01 TROUBLESHOOTING • Make sure furnace door is securely closed. • Wait 5 minutes for the system to respond. ASSISTANCE • Check circuit breaker and reset if necessary. WIRING Heating or • Set System switch to Heat.
Advanced Installation Guide ASSISTANCE WIRING SETUP Troubleshooting Temperature Make sure heating and cooling settings do not temperatures are set to acceptable change ranges: • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). “Cool On” or “Heat On” is flashing • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
One-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www.thermostat-recycle.org or 800238-8192 for information on how and where to properly and safely dispose of your old thermostat. CAUTION: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C). Automation and Control Solutions Honeywell International Inc.
Guide d’installation rapide Série RTH2510/RTH2410 Thermostat programmable 69-2602EF-01
Identifier le type de système Ce thermostat est compatible avec les systèmes suivants : Appareil de chauffage à gaz, mazout ou électrique Climatiseur central Système à eau chaude avec ou sans pompe Système à millivolts Système de chauffage et de refroidissement central Thermopompe sans chauffage de secours/auxiliaire Thermopompe avec chauffage de secours/auxiliaire Besoin d’aide? Nous sommes là pour vous aider.
1 Couper l’alimentation vers le système de chauffage/ refroidissement M28097 1 69-2602EF—01
2 Retirer l’ancien thermostat Retirer l’ancien thermostat mais laisser la plaque murale avec les fils attachés. Ne pas retirer la plaque murale à ce stade Un tube scellé contenant du mercure est-il présent? Si oui, voir au dos les consignes de mise au rebut.
3 Étiqueter les fils Étiqueter les fils au fur et à mesure qu’ils sont débranchés à l’aide des étiquettes fournies.
4 Détacher la plaque murale du nouveau thermostat Retirer la plaque murale du nouveau thermostat et la monter sur le mur.
5 Monter la plaque murale Monter la nouvelle plaque murale à l’aide des vis et des ancrages inclus. W/ Aux Not Used M32714 Percer des trous de 3/16 po pour les cloisons sèches. Percer des trous de 3/32 po pour le plâtre.
6 Brancher le câblage Il suffit de faire correspondre les étiquettes des fils. OUVERTURE POUR LES FILS G INSÉRER LES FILS ET SERRER LES VIS Y W VIS W/ Aux FILS ÉTIQUETÉS R Not Used MF32715 Retirer le cavalier métallique si les fils R et Rc sont présents. Les étiquettes ne correspondent pas? Consulter la page 22. Thermopompe présente dans le système? Consulter la page 23. Nous sommes là pour vous aider. Appeler le 1-800-468-1502 pour obtenir de l’aide pour le câblage.
7 Installer les piles Installer deux piles alcalines AAA.
8 Régler le sélecteur de fonctionnement du ventilateur Mettre le sélecteur sur le réglage désiré : Gas or Oil (Gaz ou mazout) : Pour les systèmes de chauffage à gaz ou à mazout, laisser le sélecteur de fonctionnement du ventilateur dans la position réglée en usine (pour les systèmes qui contrôlent le ventilateur lors d’un appel de chauffage). Electric or Heat Pump (Thermopompe ou électrique) : Mettre le sélecteur sur ce réglage pour les systèmes à thermopompe ou électriques.
9 Installer le thermostat sur la plaque murale Installer le thermostat sur la plaque murale sur le mur.
10 Rétablir l’alimentation Rétablir l’alimentation sur le système de chauffage/refroidissement.
11 Si le système est de type… Si le système est de type : q Chauffage et refroidissement à étage unique q Chauffage uniquement ou refroidissement uniquement Félicitations, vous avez terminé! Si le système est de type : q Thermopompe* avec chauffage de secours Passer à l’installation avancée à la page suivante pour adapter le thermostat au type de système présent. *Thermopompe—un climatiseur qui assure le refroidissement durant l’été et fonctionne à l’inverse en hiver pour assurer le chauffage.
Installation Avancée Entrer en mode de configuration du système..................... Modifier les réglages …...................................................... Type de système ................................................................ Cycle de chauffage …......................................................... Démarrage précoce …........................................................ Affichage de la température ............................................... Protection du compresseur …...........
RTH2510/RTH2410 Configuration du système Pour entrer en mode de configuration du système, appuyer sans relâcher sur les boutons s et t jusqu’à ce que l’affichage change (environ 5 secondes).
Guide d’installation avancé Modifier les réglages Voir les pages 15 à 21 pour modifier les réglages de fonction. Fonction 0 M32717 Modifier fonction ASSISTANCE Réglage 1 WIRING CONFIGURATION Configuration du système Modifier réglage 1. Appuyer sur s ou t pour modifier le réglage. 2. Appuyer simultanément sur les boutons s et t pendant une seconde pour passer à la fonction suivante. TROUBLESHOOTING 3.
RTH2510/RTH2410 Configuration du système CONFIGURATION Fonction 1 : Type de système 1 0 M32718 Appuyer sur le bouton s ou t pour sélectionner le type de système de chauffage/refroidissement utilisé dans la maison. ET Une fois terminé, appuyer sur s et t pour passer à la fonction suivante. MF32719 15 69-2602EF—01 TROUBLESHOOTING OU Appuyer sur pour modifier le réglage.
Guide d’installation avancé TROUBLESHOOTING ASSISTANCE WIRING CONFIGURATION À propos du nouveau Configuration du système thermostat Fonction 5 : Cycle de chauffage 5 5 M32720 5 Appareil de chauffage à gaz ou à mazout : Utiliser ce réglage si l’appareil de chauffage est un modèle à gaz ou à mazout standard et efficace à moins de 90 %. 6 Appareil de chauffage électrique : Utiliser ce réglage pour tout type de système de chauffage électrique.
RTH2510/RTH2410 À propos du nouveau Configuration du système thermostat CONFIGURATION Fonction 13 : Démarrage précoce 13 1 WIRING M32721 1 Marche 0 Arrêt OU Appuyer sur pour modifier le réglage. ET Une fois terminé, appuyer sur s et t pour passer à la fonction suivante. MF32719 17 69-2602EF—01 TROUBLESHOOTING Appuyer sur le bouton s ou t pour sélectionner le démarrage précoce.
Guide d’installation avancé CONFIGURATION Configuration du système Fonction 14 : Affichage de la température 14 0 WIRING M32722 0 Affichage de température en Fahrenheit (°F) TROUBLESHOOTING ASSISTANCE 1 Affichage de température en Celsius (°C) Appuyer sur le bouton s et t pour sélectionner l’affiche de la température en Fahrenheit ou en Celsius. OU Appuyer sur pour modifier le réglage. ET MF32719 69-2602EF—01 18 Une fois terminé, appuyer sur s et t pour passer à la fonction suivante.
RTH2510/RTH2410 Configuration du système 15 1 CONFIGURATION Fonction 15 : Protection du compresseur M32723 WIRING 1 Marche 0 Arrêt OU Appuyer sur pour modifier le réglage. ET Une fois terminé, appuyer sur s et t pour passer à la fonction suivante. MF32719 19 69-2602EF—01 TROUBLESHOOTING Appuyer sur le bouton s et t pour sélectionner les réglages de protection du compresseur.
Guide d’installation avancé CONFIGURATION Configuration du système Fonction 20 : Affichage de l’horloge 20 0 WIRING M32724 0 Format 12 heures TROUBLESHOOTING ASSISTANCE 1 Format 24 heures Appuyer sur le bouton s et t pour sélectionner l’affichage de l’horloge. OU Appuyer sur pour modifier le réglage. ET 69-2602EF—01 20 MF32719 Une fois terminé, appuyer sur s et t pour passer à la fonction suivante.
RTH2510/RTH2410 Configuration du système 40 0 CONFIGURATION Fonction 40 : Restaurer le programme par défaut M32725 WIRING 0 Arrêt 1 Marche - Les réglages par défaut du programme sont indiqués dans le manuel de fonctionnement. ASSISTANCE OU Appuyer sur pour modifier le réglage. Une fois terminé, appuyer sur Run (marche) pour quitter et enregistrer les changements. MF32729 21 69-2602EF—01 TROUBLESHOOTING Appuyer sur le bouton s et t pour restaurer le programme par défaut.
Guide d’installation avancé SETUP Câblage—Système conventionnel Si les étiquettes ne correspondent pas aux lettres sur le thermostat, consulter le tableau ci-dessous et faire le branchement aux bornes comme illustré ici (voir les notes ci-dessous). 4 CÂBLAGE ou ou ASSISTANCE ou ou ou Ne pas connecter B TROUBLESHOOTING ou 4 O G Y NOT W/ AUX USED R Rc MF32726 Si les fils vont être connectés aux bornes R et Rc, retirer le cavalier métallique (voir page 6). Ne pas utiliser C ou X.
RTH2510/RTH2410 Câblage—Thermopompe Brancher les fils : thermopompe 2. Utiliser un tournevis pour desserrer les vis, insérer les fils dans l’orifice sous la vis, puis serrer les vis pour maintenir les fils. SETUP 1. Faire correspondre chaque fil étiqueté avec la même lettre sur le nouveau thermostat. 3. Repousser le fil en excès dans l’ouverture du mur. CÂBLAGE G Y Aux Y W/ NOT AUX USED R R Rc MF32727 Les étiquettes ne correspondent pas? Consulter la page 24.
Guide d’installation avancé Câblage—Thermopompe SETUP Autre option de câblage (pour les thermopompes avec chauffage auxiliaire ou de secours uniquement) Si les étiquettes ne correspondent pas aux lettres sur le thermostat, consulter le tableau ci-dessous et faire le branchement aux bornes comme illustré ici (voir les notes ci-dessous).
RTH2510/RTH2410 Dépannage Rien n’apparaît • S’assurer que la porte de l’appareil de chauffage est bien fermée. à l’écran • S’assurer que des piles alcalines AAA neuves sont correctement installées (voir page 7). Régler le sélecteur sur Heat (chauffage). S’assurer que le point de consigne est plus élevé que la température ambiante. • Vérifier le disjoncteur et le réinitialiser si nécessaire. ASSISTANCE Régler le sélecteur sur Cold (refroidissement).
Guide d’installation avancé ASSISTANCE WIRING SETUP Dépannage Les réglages de la S’assurer que les températures de température chauffage et de refroidissement sont ne changent pas réglées dans les plages permises : • Chauffage : 4,5 à 32 °C (40 à 90 °F). • Refroidissement : 10 à 37 °C (50 à 99 °F). « Cool On » • (refroidissement sur marche) ou « Heat On » (chauffage sur marche) clignote La fonction de protection du compresseur est activée.
Garantie limitée d’un an Honeywell garantit ce produit, à l’exception des piles, contre tout défaut de pièce ou de main-d’œuvre, durant une période d’un (1) an à partir de la date d’achat par le consommateur si le produit est utilisé et entretenu convenablement. En cas de défectuosité ou de mauvais fonctionnement pendant la période de garantie, Honeywell remplacera ou réparera le produit, à sa discrétion.
AVIS RELATIF AU MERCURE : Ne pas jeter l’ancien thermostat dans la poubelle s’il contient du mercure dans un tube scellé. Contacter le Thermostat Recycling Corporation à www. thermostat-recycle.org ou le 800-238-8192 pour obtenir de l’information sur la façon et l’endroit appropriés de se débarrasser du vieux thermostat. MISE EN GARDE : Pour éviter d’endommager le compresseur, ne pas faire fonctionner le climatiseur si la température extérieure est inférieure à 10 °C (50 °F).