69-2380ES-01 (RTH2510 7-day QIG) ENG USA.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 0 Tuesday, October 20, 2009 10:16 AM Do you need assistance? We are here to help. Call 1-800-468-1502.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 1 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 n Identify System Type 1. This thermostat is compatible with the following systems: • • • • • • • Gas, oil or electric furnace Central air conditioner Hot water system with or without pump Millivolt system Central heating and cooling system Heat pump without auxiliary/backup heat Heat pump with auxiliary/backup heat This thermostat cannot be used on multistage systems.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 2 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide o Remove Old Thermostat 1) Turn power off at the heating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. 2. Do not remove wallplate yet. MERCURY NOTICE: Do not put your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 3 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 p Identify Wires 3. If any wires are not attached to your old thermostat or are attached to a terminal marked C or C1, they will not be connected to your new thermostat. Wrap the bare metal end of each of these wires with electrical tape, so it cannot touch and short other wires. Do not use non-connected wires. Do not use C or C1 wires Identify and label each wire.
9-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 4 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide q 1) 2) 3) 4) 5) 6) 7) Mount New Wallplate 4. Loosen the locking screw at the bottom of the thermostat. Note that the screw is captive and cannot be removed from the wallplate. Separate the thermostat from the wallplate as per Figure 1. Position the wallplate against the wall and mark hole positions with a pencil.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 5 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 r Connect Wires 5. Conventional Systems (Typical Wiring) 1) Match each labeled wire with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any excess wire back into the wall opening. • Labels don’t match? See page 6. • Have a heat pump with auxiliary/backup heat, see pages 7-8.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 6 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide r Connect Wires (cont’d) 6. Conventional Systems (Alternate Wiring) Do not use C, C1 or X wire. Do not use B wire if you already have O wire. Wrap bare end of wire with electrical tape. This thermostat cannot be used if your old thermostat had any two of the following wires: R, RC, RH, 4 and V.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 7 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 r Connect Wires (cont’d) 7. Heat Pump Systems with Auxiliary/Backup Heat (Typical Wiring) 1) Match each labeled wire with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any excess wire back into the wall opening. Labels don’t match? See page 8.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 8 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide r Connect Wires (cont’d) 8. Heat Pump Systems with Auxiliary/Backup Heat (Alternate Wiring) If your old thermostat had E and Aux wires (or alternate wires), connect both wires to AUX terminal. Do not use L wire. Wrap bare end of wire with electrical tape. Do not use C or X wire. Do not use B wire if you already have O wire. Wrap bare end of wire with electrical tape.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 9 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 s Set Heating Fan Control 9. Set jumper JP1, on the back of the thermostat, if you have connected a wire to the G terminal. JP1 HG Leave the jumper in this factory-set position if you have a gas or oil furnace. HE Place the jumper to this position if you have an electric furnace. Incorrect jumper setting: An incorrect setting is noticeable in a gas or oil heating system.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 10 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide t Set Heat Pump Reversing Valve 10. Set jumper JP2, on the back of the thermostat, if you have a heat pump. JP2 O Leave the jumper in this factory-set position if you have connected O wire to the O/B terminal. B Place the jumper to this position if you have connected B wire to the O/B terminal. Incorrect jumper setting: The heat pump operation will be reversed, i.e.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 11 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 u Install Batteries and Thermostat 1) Install 2 AAA batteries on the back of the thermostat. 2) Align the two brackets on the top of the thermostat with the corresponding slots on the top of the wallplate. 3) Push the thermostat against the wallplate. 4) Tighten the screw at the bottom of the thermostat. 5) Turn power back on at the heating/ cooling system. 11 11.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 12 Tuesday, October 20, 2009 10:16 AM Quick Installation Guide v 12. System Setup Follow the procedure below to personalize and configure the thermostat according to the heating/ cooling system. 1) Press the Up and Down buttons simultaneously (for three seconds) until the display appears as shown below. See table on the next page. Function number Option number 2) Press the Up or Down button to change the option.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 13 Tuesday, October 20, 2009 10:16 AM Programmable Thermostat RTH2510 v System Setup (cont’d) Function 1 Temperature display format 2 Time display format Default setting 13.
69-2380ES-01 (RTH2510 7-day QIG) ENG USA.fm Page 14 Tuesday, October 20, 2009 10:16 AM Automation and Control Systems Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 http://DIYthermostats.honeywell.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 2 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida o Retirar el viejo termostato 1) Cortar la electricidad del sistema de calefacción/ aire acondicionado. 2) Retirar el viejo termostato pero dejar la placa mural con los cables conectados. 2. No retirar la placa mural todavía ADVERTENCIA SOBRE EL MERCURIO No arrojar el viejo termostato a la basura si contiene mercurio en un tubo sellado.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 3 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 p Identificar los cables 3. Si en el viejo termostato hubiera cables no conectados o conectados a un terminal marcado C o C1, estos cables no se usarán con el nuevo termostato. Recubrir el extremo de metal desnudo de cada uno con cinta aisladora para que no puedan tocarse y producir un corto circuito.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 4 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida q 1) 2) 3) 4) 5) Instalar la nueva placa mural 4. Aflojar los tornillos de la base del termostato. El tornillo está cautivo y no se lo puede retirar de la base. Separar el termostato de la placa mural como se indica en la Figura 1. Colocar la placa mural contra la pared y marcar la posición de los agujeros con un lápiz.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 5 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 r Conectar los cables 5. Sistemas convencionales (conexión típica) 1) Hacer coincidir cada cable etiquetado con el terminal de la misma letra. 2) Aflojar los tornillos del terminal con un destornillador, introducir los cables y reajustar los tornillos. 3) Empujar el exceso de cables en el agujero de la pared. • ¿Las etiquetas no coinciden? Ver la pág. 6.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 6 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida r Conectar los cables (cont.) 6. Sistemas convencionales (conexión alternativa) No usar los cables C, C1 o X. No usar el cable B si ya existe un cable O. Envolver el extremo desnudo de los cables con cinta aisladora. No puede usarse este termostato si el viejo termostato tuviera dos de los siguientes cables: R, RC, RH, 4 y V.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 7 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 r Conectar los cables (cont.) 7. Sistemas de bombas de calor con calefactor auxiliar (conexión típica) 1) Hacer coincidir cada cable etiquetado con el terminal de la misma letra. 2) Aflojar los tornillos del terminal con un destornillador, introducir los cables y reajustar los tornillos. 3) Empujar el exceso de cables en el agujero de la pared.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 8 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida r Conectar los cables (cont.) 8. Sistemas de bombas de calor con calefactor auxiliar (conexión alternativa) Si el viejo termostato tiene cables E y Aux (o cables alternativos), conectar ambos cables al terminal AUX. No usar el cable L. Envolver el extremo desnudo con cinta aisladora. No usar los cables C o X. No usar el cable B si ya hay un cable O.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 9 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 s Ajuste del control del ventilador de la calefacción 9. Ajustar el puente JP1, en la parte de atrás del termostato, si se conectó un cable al terminal G. JP1 HG Dejar el puente en este ajuste de fábrica en el caso de una estufa a gas o a aceite. HE Poner el puente en esta posición en el caso de una estufa eléctrica.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 10 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida t Ajuste de la válvula de inversión 10. Ajustar el puente JP2, en la parte de atrás del termostato, en el caso de una bomba de calor. JP2 O Dejar el puente en este ajuste de fábrica si hay un cable O conectado al terminal O/B. B Poner el puente en esta posición si hay un cable B conectado al terminal O/B.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 11 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 u Instalación de las pilas y del termostato 1) Instalar 2 pilas AAA en la parte de atrás del termostato. 2) Alinear las dos lengüetas de la parte superior del termostato con las ranuras correspondientes de la parte superior de la placa mural. 3) Empujar el termostato contra la placa mural. 4) Ajustar el tornillo en la parte inferior del termostato.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 12 Tuesday, October 20, 2009 10:09 AM Guía de instalación rápida v Configuración del sistema 12. El procedimiento a continuación permite personalizar y configurar el termostato según el sistema de calefacción/enfriamiento. 1) Presionar los botones Arriba y Abajo al mismo tiempo (3 seg.) hasta que se vea lo que se indica en la ilustración. Ver el cuadro en la página siguiente.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 13 Tuesday, October 20, 2009 10:09 AM Termostato programable RTH2510 v Configuración del sistema (cont.) Función 1 Formato de la temperatura 2 Formato de la hora Ajuste por defecto Opciones 0 0: Fahrenheit 1: Celsius 0 0: 12 horas 1: 24 horas 3 Ciclos de calefacción por hora 5 2 a 6 ciclos por hora • 2: 30 min. (vapor, gravedad) • 3: 20 min. (agua caliente, 90%+ estufa de alto rendimiento) • 4: 15 min. (gas o aceite) • 5: 12 min.
69-2380ES-01 (RTH2510 7-day QIG) SPA USA.fm Page 14 Tuesday, October 20, 2009 10:09 AM Sistemas para automatización y control Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 http://DIYthermostats.honeywell.com Impreso en EE.UU.
