Installation Guide RTH4300B Programmable Thermostat 69-1772EF
TURN OFF POWER at the heating/cooling system or the fuse/circuit breaker panel before you begin. MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal. Need Help? For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 Read and save these instructions. ® U.S.
RTH4300B Programmable Thermostat Table of contents Getting started System setup Installation tips............................................ 2 Pre-installation checklist............................ 3 How to change settings........................... 17 Set system type........................................ 18 Set heating cycle rate............................... 19 Set temperature display........................... 20 Old thermostat removal Remove old thermostat..............................
Installation Guide Installation is easy — even if you’ve never done it before! Your new thermostat has been designed for fast, easy installation. Just follow the simple, step-by-step instructions in the following pages. Install in three simple steps • Label wires and remove your old thermostat (see pages 5-8). • Install and wire your new thermostat (see pages 9-16). • Set your new thermostat to match your heating/cooling system (see pages 17-20).
RTH4300B Programmable Thermostat Pre-installation checklist Check to make sure your package includes the following items: RTH4300B thermostat (wallplate attached to back) Quick reference card Wall anchors and mounting screws (2 each) Operating manual Wire labels
Installation Guide Pre-installation checklist Required tools & supplies • No.
RTH4300B Programmable Thermostat Remove your old thermostat 1. Turn off power at heating/cooling system (or fuse/circuit-breaker panel). 2. Remove cover and thermostat, but leave wallplate with wires attached. Leave wallplate in place Is there a sealed tube containing mercury? If so, see inside front cover of this manual for proper disposal instructions.
Installation Guide Did you purchase right thermostat? Count wires to check. Count the number of wires coming out of the wall and attached to terminals in your old thermostat. If any of them are attached to a terminal marked “C” or “C1” do not count that wire in your total. If the total (not counting C or C1) is 5 wires or less, proceed to the next page. If you have 6 or more wires, your new thermostat may not be compatible with your system. Stop installation and call 1-800-468-1502 for advice.
RTH4300B Programmable Thermostat Identify wires you will not use If any wires are not attached to terminals in your old thermostat, do not connect them to your new thermostat. If a wire is attached to a terminal marked “C” or “C1,” disconnect it. You will not connect it to your new thermostat. Wrap the bare metal ends of each unused wire with electrical tape, so it cannot touch and short out other wires. Do not use unconnected wires. Do not use C or C1 wire.
Installation Guide Label wires and remove old wallplate Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with the label matching the letter on your old thermostat. (Adhesive labels are supplied in your thermostat package.) Remove the old wallplate only after all wires are labeled. Be careful not to let loose wires fall into the wall opening. Wrap supplied labels securely around each wire.
RTH4300B Programmable Thermostat Remove wallplate and install quick reference card Pull at bottom to remove thermostat from wallplate. Insert quick reference card after wallplate is mounted (see mounting instructions on page 11).
Installation Guide Mark wallplate mounting position 1. Pull wires through wallplate. 2. Level wallplate if desired (lay level across tabs). 10 3. Mark positions of both screw holes.
RTH4300B Programmable Thermostat About your Mount wallplate new thermostat 1. Drill holes at pencil-marked locations: 3/16” holes for drywall 7/32” holes for plaster. 2. Use hammer to tap anchors into holes until flush with wall. 3. Place wallplate over anchors and insert screws. Check level if desired, then tighten screws.
Installation Guide Connect wires (typical installation) 1. Match each labeled wire with same letter on terminal. Remove metal jumper if you have both R and Rc wires. 2. Use a screwdriver to loosen screw terminals, insert wires, then tighten screws. 3. Push any excess wire back into the wall opening. Labels don’t match? If labels do not match letters on thermostat, see next page.
RTH4300B Programmable Thermostat Connect wires (less common wire designations) If labels do not match letters on the thermostat, check the chart at right and connect to terminal as shown here (see notes, below). If wires will be connected to both R and Rc terminals, remove metal jumper (see page 12). Do not use C, X, or B. Wrap bare end of wire with electrical tape. Do not connect both O and B if you have a heat pump. Connect O wire to O. Wrap B wire with electrical tape and do not use.
Installation Guide Install batteries Install two fresh AA alkaline batteries in back of thermostat. After installation, batteries can be changed without removing the thermostat from the wall (see Operating Manual for more information).
RTH4300B Programmable Thermostat About Set fanyour operation new thermostat switch Move the switch to the proper setting: F: For gas or oil heating systems, leave the fan operation switch in this factory-set position (for systems that control the fan in a call for heat). E: Change the switch to this setting for heat pump or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal.
Installation Guide About your Mount thermostat new thermostat and restore electrical power 1. Align the 4 tabs on the wallplate with corresponding slots on the back of the thermostat, then push gently until the thermostat snaps into place. Wallplate 2. Restore electrical power at the heating/cooling system, or at the fuse/circuit-breaker panel. Thermostat TIP: If wires interfere when you try to mount the thermostat, push excess wire back into the wall opening.
RTH4300B Programmable Thermostat About your System setup new (set thermostat thermostat to match your system) Next, you must set the thermostat to match the heating/cooling system in your home. Press and hold the s and t buttons to enter system setup. Function number Setting 1 Setup 0 Press t to change settings. Press s to advance to next function. Press and hold ts to exit and save settings. To begin, press and hold the s and t buttons until the display changes.
Installation Guide About your Function 1: new System thermostat type 1 Setup 0 Press the t button to select the type of climate control system you have in your home: 0 Heating & cooling: Gas, oil or electric heating with central air conditioning. 1 Heat pump: Outside compressor provides both heating and cooling. Press to change setting. When finished, press to advance to the next function.
RTH4300B Programmable Thermostat About your Function 5: new Heating thermostat cycle rate 5 Setup 5 Press the t button to select your heating system and optimize its operation: 5 Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient. 9 Electric furnace: Use this setting if you have any type of electric heating system.
Installation Guide About your Function 14:new Temperature thermostatdisplay 14 Setup 0 Press the t button to select Fahrenheit or Celsius temperature display: 0 Fahrenheit temperature display (°F) 1 Celsius temperature display (°C) Press to change setting.
RTH4300B Programmable Thermostat About In caseyour of difficulty new thermostat If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • • Check circuit breaker and reset if necessary. Make sure heating & cooling power switches are on. Make sure furnace door is closed securely. Make sure fresh AA alkaline batteries are correctly installed (see page 14).
Installation Guide About In caseyour of difficulty new thermostat Temperature settings do not change Make sure heating and cooling temperatures are set to acceptable ranges: • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). “Cool On” or “Heat On” is flashing • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
RTH4300B Programmable Thermostat Customer assistance Pull at bottom to remove thermostat from wallplate. Turn thermostat over to find model number and date code. For assistance with this product, please visit http://yourhome.honeywell.com. Or call Honeywell Customer Care toll-free at 1-800-468-1502. To save time, please note your model number and date code before calling. Accessories To order, please call Honeywell Customer Care toll-free at 1-800-468-1502. Cover plate*................. Part No.
Installation Guide 1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
RTH4300B Programmable Thermostat 1-year limited warranty INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT.
Automation and Control Systems Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2006 Honeywell International Inc. 69-1772EF M.S.
Guide d’installation RTH4300B Thermostat programmable 69-1772EF
COUPER L’ALIMENTATION du système de chauffage/climatisation, ou du panneau à disjoncteurs, avant de commencer. REMARQUE À PROPOS DU MERCURE : Ne pas jeter l’ancien thermostat aux ordures s’il contient du mercure scellé dans un tube. Consulter l’administration locale de gestion des déchets pour connaître les instructions relatives au recyclage et à l’élimination. Besoin d’aide? Pour obtenir de l’assistance au sujet de ce produit, consulter le http://yourhome.honeywell.
Thermostat programmable RTH4300B À propos Table desdu matières thermostat Pour commencer Réglage du système Conseils d’installation................................. 2 Liste de vérification avant l’installation....... 3 Comment changer les réglages............... 17 Régler le type de système........................ 18 Régler le rythme de cycle de chauffage.... 19 Régler l’indicateur de température.......... 20 Enlèvement de l’ancien thermostat Enlever l’ancien thermostat........................
Guide d’installation À propos du Installation facile thermostat — même si vous ne l’avez jamais fait auparavant! Votre nouveau thermostat a été conçu pour être installé rapidement et facilement. Vous n’avez qu’à suivre les instructions pas à pas des pages suivantes. Installation en trois étapes toutes simples • Marquer les fils et enlever l’ancien thermostat (pages 5-8). • Installer et brancher le nouveau thermostat (pages 9-16).
Thermostat programmable RTH4300B Liste de vérification avant l’installation L’emballage doit contenir les éléments suivants : Thermostat RTH4300B (plaque murale fixée à l’arrière) Carte de référence rapide Fixations murales et vis de montage (2 chacune) Guide d’utilisation Étiquettes de fils
Guide d’installation Liste de vérification avant l’installation Éléments requis • Tournevis cruciforme no 2 • Petit tournevis de poche • Perceuse • Foret (3/16 pour cloison sèche, 7/32 pour plâtre) • Marteau • Crayon • Ruban isolant • Niveau (optionnel) • Deux piles alcalines AA neuves
Thermostat programmable RTH4300B Enlever l’ancien thermostat 1. Couper l’alimentation du système de chauffage/climatisation (ou du panneau à disjoncteurs). 2. Enlever le couvercle et le thermostat, mais laisser la plaque murale et les fils en place. Laisser la plaque murale en place Y a-t-il un tube hermétique contenant du mercure? Si c’est le cas, consulter les directives d’élimination sur la deuxième de couverture de ce guide.
Guide d’installation Avez-vous acheté le bon thermostat? Comptez les fils pour vérifier. Comptez le nombre de fils sortant du mur et branchés aux bornes de l’ancien thermostat. Si des fils sont branchés à une borne marquée «C» ou «C1» ne pas les ajouter au total. Si le total (sans compter C ou C1) est de 5 fils ou moins, allez à la page suivante. Si vous avez 6 fils ou plus, votre nouveau thermostat pourrait ne pas être compatible avec votre système.
Thermostat programmable RTH4300B Identifier les fils dont vous ne vous servirez pas Si des fils ne sont pas branchés aux bornes de l’ancien thermostat, ne pas les brancher au nouveau thermostat. Si un fil est branché à une borne marquée «C» ou «C1», débranchez-le. Il ne sera pas branché au nouveau thermostat. Recouvrir le bout dénudé de chaque fil non utilisé de ruban isolant, pour éviter qu’ils ne se touchent et court-circuitent les autres fils. Ne pas se servir des fils débranchés.
Guide d’installation Étiqueter les fils et enlever l’ancienne plaque murale Employer un tournevis pour débrancher les fils un à un. Enrouler l’étiquette de fil correspondant à la lettre de l’ancien thermostat sur chaque fil à mesure que vous les débranchez. (Des étiquettes adhésives sont incluses avec le thermostat.) Enlever l’ancienne plaque murale seulement après avoir étiqueté tous les fils. Faire attention à ne pas laisser les fils débranchés tomber dans le mur.
Thermostat programmable RTH4300B Enlever la plaque murale et installer la carte de référence. Tirer le thermostat par le bas pour le détacher de la plaque murale. Insérer l’aide-mémoire après avoir fixé la plaque murale au mur (voir les directives d’installation à la page 11).
Guide d’installation Marquer l’emplacement d’installation de la plaque murale 1. Passer les fils au travers de la plaque murale. 2. Si désiré, niveler la plaque murale (placer le niveau sur les languettes). 10 3. Marquer l’emplacement des deux trous de vis.
Thermostat programmable RTH4300B À propos l’emplacement Marquer du thermostat d’installation de la plaque murale 1. Percer les trous aux endroits marqués : trous 3/16 pour cloison sèche et 7/32 pour le plâtre 2. Employer un marteau pour enfoncer les fixations dans les trous jusqu’à ce qu’elles soient encastrées dans le mur. 3. Placer la plaque murale sur les fixations et insérer les vis. Si désiré, mettre de niveau, puis serrer les vis.
Guide d’installation Brancher les fils (installation habituelle) 1. Associer chaque fil étiqueté à la lettre correspondante sur la borne. Enlever le cavalier en métal si vous avez des fils R et Rc. 2. Employer un tournevis pour dévisser les bornes à vis, insérer les fils et serrer les vis. 3. Repousser tous les fils excédents dans le mur. Les étiquettes ne correspondent pas? Si les étiquettes ne correspondent pas aux lettres du thermostat, consulter la page suivante.
Thermostat programmable RTH4300B Brancher les fils (configurations rares) Si les étiquettes ne correspondent pas aux lettres du thermostat, consulter la grille à droite (voir les notes dessous). Si des fils seront branchés aux bornes R et Rc, enlever le cavalier en métal (page 12). Ne pas se servir de C, X, ou B. Enrouler du ruban isolant sur le bout dénudé du fil. Ne pas brancher Ne pas brancher O et B si vous avez une thermopompe. Brancher le fil O à O.
Guide d’installation Placer les piles Placer deux piles alcalines AA neuves à l’arrière du thermostat. Après l’installation, les piles peuvent être remplacées sans enlever le thermostat du mur (voir le Guide d’utilisation pour obtenir plus d’information).
Thermostat programmable RTH4300B À propos du Réglages du thermostat ventilateur Placer le sélecteur à la position qui correspond au système : F : S’il s’agit d’un système de chauffage au gaz ou au mazout, laisser le sélecteur à la position réglée en usine (pour les systèmes qui commandent la mise en marche du ventilateur lors d’une demande de chaleur). E : Déplacer le commutateur à cette position si le système est une thermopompe ou un appareil de chauffage électrique.
Guide d’installation À proposleduthermostat Installer thermostatet rétablir le courant 1. Placer les fentes à l’arrière du thermostat vis à vis des languettes correspondantes de la plaque murale, puis appuyer doucement jusqu’à ce qu’elles s’engagent une dans l’autre. Plaque murale 2. Rétablir l’alimentation du système de chauffage/climatisation ou du panneau à disjoncteurs. Thermostat ASTUCE : Si des fils nuisent à l’installation du thermostat, pousser les fils non utilisés dans le mur.
Thermostat programmable RTH4300B Réglage du système (pour faire correspondre le thermostat à votre système) Ensuite, configurer le thermostat pour le réglage du système de chauffage et de climatisation de votre résidence. Appuyer sur les touches s et t et les maintenir enfoncées pour initier la configuration. Numéro Réglage de fonction 1 Setup 0 Appuyer sur t pour modifier les réglages. Appuyer sur s pour passer à la fonction suivante.
Guide d’installation À propos 1du: Type Fonction thermostat de système 1 Setup 0 Appuyer sur cette touche pour changer le réglage. Après avoir terminé, appuyer sur cette touche pour aller à la prochaine fonction. Appuyer sur les touches t pour sélectionner le type de système de climatisation que vous avez dans votre résidence : 0 Chauffage et climatisation : Chauffage au gaz naturel, au mazout ou à l’électricité avec climatiseur central.
Thermostat programmable RTH4300B À propos 5du: Rythme Fonction thermostat de cycle de chauffage 5 Setup 5 Appuyer sur cette touche pour changer le réglage. Après avoir terminé, appuyer sur cette touche pour aller à la prochaine fonction.
Guide d’installation À propos 14 Fonction du :thermostat Affichage de la température 14 Setup 0 Appuyer sur les touches t pour choisir d’afficher la température en Fahrenheit ou en Celsius : 0 Affichage de la température en Fahrenheit (°F) 1 Affichage de la température en Celsius (°C) Appuyer sur cette touche pour changer le réglage. Une fois terminé, appuyer sur le bouton RUN ou appuyer simultanément sur les boutons s et t et les maintenir enfoncés pour quitter et sauvegarder les changements.
Thermostat programmable RTH4300B À propos En cas dedu problème thermostat Si le thermostat cause des ennuis, essayer l’une de ces suggestions. La plupart des problèmes peuvent être réglés rapidement et facilement. L’écran est vide • • • • Le système de chauffage ou de climatisation ne fonctionne pas • • • • • • Vérifier le disjoncteur et réinitialiser si nécessaire. S’assurer que les commutateurs de chauffage et de climatisation fonctionnent.
Guide d’installation À propos En cas dedu problème thermostat Les réglages de S’assurer que le réglage des températures de chauffage et de climatisation la température est acceptable : ne changent pas • Heat : 4,5 à 32°C (40 à 90°F) • Cool : 10 à 37°C (50 à 99°F) Les mentions “Cool On” ou “Heat On” clignotent • La fonction de protection du compresseur est activée. Attendre 5 minutes que le système redémarre en toute sécurité, sans endommager le compresseur.
Thermostat programmable RTH4300B Assistance à la clientèle Tirer le thermostat par le bas pour le détacher de la plaque murale. Pour obtenir de l’aide avec ce produit, veuillez consulter le site http://yourhome.honeywell.com. Regarder au dos du thermostat pour connaître le numéro de modèle et le code dateur. Pour gagner du temps, écrire le numéro de modèle et le code dateur avant d’appeler. Ou téléphoner sans frais au Centre de service à la clientèle de Honeywell au 1 800 468-1502.
Guide d’installation Garantie limitée d’un an Honeywell garantit ce produit, à l’exception des piles, contre tout défaut de pièce ou de maind’oeuvre, durant une période d’un (1)an à partir de la date d’achat si le produit est utilisé et entretenu convenablement. Si, à n’importe quel moment de la période de garantie, le produit est défectueux, Honeywell le réparera ou le remplacera (à sa discrétion).
Thermostat programmable RTH4300B Garantie limitée d’un an OU DOMMAGE DE TOUTES SORTES, INCLUANT LES DOMMAGES ACCIDENTELS OU CONSÉCUTIFS RÉSULTANT, DIRECTEMENT OU INDIRECTEMENT, DE TOUT MANQUEMENT À N’IMPORTE QUELLE GARANTIE, EXPRESSE OU IMPLICITE, OU DE TOUTE AUTRE DÉFAILLANCE DU PRODUIT. Certains États ou provinces ne permettent pas l’exclusion ou la restriction des dommages accidentels ou consécutifs, cette restriction pourrait donc ne pas s’appliquer.
Systèmes d’automatisation et de contrôle Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com Imprimé aux É.-U. sur du papier recyclé contenant au moins 10 % de fibres de papier recyclées après consommation. ® Marque déposée aux É.-U. © 2006 Honeywell International Inc. 69-1772EF M.S.