Installation Guide RTH4300B Programmable Thermostat 69-1772ES
TURN OFF POWER at the heating/cooling system or the fuse/circuit breaker panel before you begin. MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal. Need Help? For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 Read and save these instructions. ® U.S.
RTH4300B Programmable Thermostat Table of contents Getting started System setup Installation tips............................................ 2 Pre-installation checklist............................ 3 How to change settings........................... 17 Set system type........................................ 18 Set heating cycle rate............................... 19 Set temperature display........................... 20 Old thermostat removal Remove old thermostat..............................
Installation Guide About your new Installation is easy thermostat — even if you’ve never done it before! Your new thermostat has been designed for fast, easy installation. Just follow the simple, step-by-step instructions in the following pages. Install in three simple steps • Label wires and remove your old thermostat (see pages 5-8). • Install and wire your new thermostat (see pages 9-16). • Set your new thermostat to match your heating/cooling system (see pages 17-20).
RTH4300B Programmable Thermostat About your new checklist Pre-installation thermostat Check to make sure your package includes the following items: RTH4300B thermostat (wallplate attached to back) Quick reference card Wall anchors and mounting screws (2 each) Operating manual Wire labels
Installation Guide About your new checklist Pre-installation thermostat Required tools & supplies • No.
RTH4300B Programmable Thermostat About your Remove your new oldthermostat thermostat 1. Turn off power at heating/cooling system (or fuse/circuit-breaker panel). 2. Remove cover and thermostat, but leave wallplate with wires attached. Leave wallplate in place Is there a sealed tube containing mercury? If so, see inside front cover of this manual for proper disposal instructions.
Installation Guide About Did youyour purchase new thermostat right thermostat? Count wires to check. Count the number of wires coming out of the wall and attached to terminals in your old thermostat. If any of them are attached to a terminal marked “C” or “C1” do not count that wire in your total. If the total (not counting C or C1) is 5 wires or less, proceed to the next page. If you have 6 or more wires, your new thermostat may not be compatible with your system.
RTH4300B Programmable Thermostat About your Identify wires new you thermostat will not use If any wires are not attached to terminals in your old thermostat, do not connect them to your new thermostat. If a wire is attached to a terminal marked “C” or “C1,” disconnect it. You will not connect it to your new thermostat. Wrap the bare metal ends of each unused wire with electrical tape, so it cannot touch and short out other wires. Do not use unconnected wires. Do not use C or C1 wire.
Installation Guide About wires Label your new and thermostat remove old wallplate Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with the label matching the letter on your old thermostat. (Adhesive labels are supplied in your thermostat package.) Remove the old wallplate only after all wires are labeled. Be careful not to let loose wires fall into the wall opening. Wrap supplied labels securely around each wire.
RTH4300B Programmable Thermostat About your Remove wallplate new thermostat and install quick reference card Pull at bottom to remove thermostat from wallplate. Insert quick reference card after wallplate is mounted (see mounting instructions on page 11).
Installation Guide Aboutwallplate Mark your newmounting thermostat position 1. Pull wires through wallplate. 2. Level wallplate if desired (lay level across tabs). 10 3. Mark positions of both screw holes.
RTH4300B Programmable Thermostat About your Mount wallplate new thermostat 1. Drill holes at pencil-marked locations: 3/16” holes for drywall 7/32” holes for plaster. 2. Use hammer to tap anchors into holes until flush with wall. 3. Place wallplate over anchors and insert screws. Check level if desired, then tighten screws.
Installation Guide About your Connect wires new(typical thermostat installation) 1. Match each labeled wire with same letter on terminal. Remove metal jumper if you have both R and Rc wires. 2. Use a screwdriver to loosen screw terminals, insert wires, then tighten screws. 3. Push any excess wire back into the wall opening. Labels don’t match? If labels do not match letters on thermostat, see next page.
RTH4300B Programmable Thermostat About your Connect wires new(less thermostat common wire designations) If labels do not match letters on the thermostat, check the chart at right and connect to terminal as shown here (see notes, below). If wires will be connected to both R and Rc terminals, remove metal jumper (see page 12). Do not use C, X, or B. Wrap bare end of wire with electrical tape. Do not connect both O and B if you have a heat pump. Connect O wire to O.
Installation Guide About your Install batteries new thermostat Install two fresh AA alkaline batteries in back of thermostat. After installation, batteries can be changed without removing the thermostat from the wall (see Operating Manual for more information).
RTH4300B Programmable Thermostat About Set fanyour operation new thermostat switch Move the switch to the proper setting: F: For gas or oil heating systems, leave the fan operation switch in this factory-set position (for systems that control the fan in a call for heat). E: Change the switch to this setting for heat pump or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal.
Installation Guide About your Mount thermostat new thermostat and restore electrical power 1. Align the 4 tabs on the wallplate with corresponding slots on the back of the thermostat, then push gently until the thermostat snaps into place. Wallplate 2. Restore electrical power at the heating/cooling system, or at the fuse/circuit-breaker panel. Thermostat TIP: If wires interfere when you try to mount the thermostat, push excess wire back into the wall opening.
RTH4300B Programmable Thermostat About your System setup new (set thermostat thermostat to match your system) Next, you must set the thermostat to match the heating/cooling system in your home. Press and hold the s and t buttons to enter system setup. Function number Setting 1 Setup 0 Press t to change settings. Press s to advance to next function. Press and hold ts to exit and save settings. To begin, press and hold the s and t buttons until the display changes.
Installation Guide About your Function 1: new System thermostat type 1 Setup 0 Press the t button to select the type of climate control system you have in your home: 0 Heating & cooling: Gas, oil or electric heating with central air conditioning. 1 Heat pump: Outside compressor provides both heating and cooling. Press to change setting. When finished, press to advance to the next function.
RTH4300B Programmable Thermostat About your Function 5: new Heating thermostat cycle rate 5 Setup 5 Press the t button to select your heating system and optimize its operation: 5 Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient. 9 Electric furnace: Use this setting if you have any type of electric heating system.
Installation Guide About your Function 14:new Temperature thermostatdisplay 14 Setup 0 Press the t button to select Fahrenheit or Celsius temperature display: 0 Fahrenheit temperature display (°F) 1 Celsius temperature display (°C) Press to change setting.
RTH4300B Programmable Thermostat About In caseyour of difficulty new thermostat If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • • Check circuit breaker and reset if necessary. Make sure heating & cooling power switches are on. Make sure furnace door is closed securely. Make sure fresh AA alkaline batteries are correctly installed (see page 14).
Installation Guide About In caseyour of difficulty new thermostat Temperature settings do not change Make sure heating and cooling temperatures are set to acceptable ranges: • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). “Cool On” or “Heat On” is flashing • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
RTH4300B Programmable Thermostat About yourassistance Customer new thermostat Pull at bottom to remove thermostat from wallplate. Turn thermostat over to find model number and date code. For assistance with this product, please visit http://yourhome.honeywell.com. Or call Honeywell Customer Care toll-free at 1-800-468-1502. To save time, please note your model number and date code before calling. Accessories To order, please call Honeywell Customer Care toll-free at 1-800-468-1502. Cover plate*.........
Installation Guide About your 1-year limited new warranty thermostat Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
RTH4300B Programmable Thermostat About your 1-year limited new warranty thermostat INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT.
Automation and Control Systems Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2006 Honeywell International Inc. 69-1772ES M.S.
Guía de instalación RTH4300B Termostato programable 69-1772ES
CORTE LA ELECTRICIDAD del sistema de calefacción/refrigeración o del panel del interruptor de circuito/fusible antes de comenzar. AVISO SOBRE EL MERCURIO: No arroje el viejo termostato a la basura si éste contiene mercurio en tubo sellado. Póngase en contacto con la autoridad local para el manejo de desechos a fin de obtener instrucciones sobre el reciclado y la correcta eliminación de este tipo de desechos.
Termostato programable RTH4300B Acerca de su nuevo termostato Índice Inicio Configuración del sistema Consejos para la instalación...................... 2 Lista de control previo a la instalación...... 3 Cómo cambiar las configuraciones......... 17 Configuración del tipo de sistema........... 18 Configuración de la velocidad del ciclo térmico.............................................. 19 Configuración de la temperatura que se muestra en la pantalla..............................
Guía de instalación Acerca La instalación de su nuevo es fácil, termostato aunque nunca antes lo haya hecho. Su nuevo termostato fue diseñado para una instalación más rápida y fácil. Simplemente siga las instrucciones paso a paso de las páginas siguientes. Instálelo en tres pasos • Coloque etiquetas en los cables y quite el viejo termostato (vea las páginas 5 a 8). • Instale y coloque los cables de su nuevo termostato (vea las páginas 9 a 16).
Termostato programable RTH4300B Acerca Lista dede control su nuevo previo termostato a la instalación Controle que el embalaje contenga los siguientes artículos: Termostato RTH4300B (placa de pared sujeta en la parte posterior) Tarjeta de referencia rápida Manual de funcionamiento Anclas de expansión y tornillos de montaje (2 de cada uno) Etiquetas para cables
Guía de instalación Acerca Lista dede control su nuevo previo termostato a la instalación Herramientas y suministros necesarios • Destornillador Phillips N.
Termostato programable RTH4300B Acercaelde Quite viejo su termostato nuevo termostato 1. Corte la electricidad del sistema de calefacción y refrigeración (o del panel del interruptor de circuito/fusible). 2. Quite la cubierta y el termostato, y deje la placa para pared con los cables sujetos a ella. Deja la placa para pared en su lugar ¿Hay un tubo sellado con mercurio? En tal caso, vea la tapa interior frontal de este Manual de instrucciones para la administración de estos desechos.
Guía de instalación Acerca deelsu ¿Compró termostato nuevo termostato adecuado? Cuente los cables. Cuente el número de cables que salen de la pared y los terminales sujetos al viejo termostato. Si alguno de los cables está conectado a un terminal marcado con “C” o “C1” no cuente ese cable. Si el total (sin contar el cable del terminal C o C1) es igual a 5 cables o menos, continúe con el paso siguiente. Si hay 6 cables o más, es posible que su nuevo termostato no sea compatible con su sistema.
Termostato programable RTH4300B Acerca de su Identifique losnuevo cables termostato que no usará Si alguno de los cables no está conectado a en los terminales del viejo termostato, no lo conecte a su nuevo termostato. Si un cable está conectado en el terminal “C” o “C1”, desconéctelo. No lo conecte a su nuevo termostato. Envuelva con cinta aisladora las terminaciones de metal desnudo de los cables que no utilice para que no toquen otros cables ni provoquen un cortocircuito.
Guía de instalación Acerca etiquetas Coloque de su nuevo en lostermostato cables y quite las viejas placas para pared Utilice un destornillador para desconectar los cables uno por uno. A medida que desconecta cada cable, colóquele la etiqueta que se corresponda con la letra del viejo termostato (el embalaje del termostato contiene etiquetas autoadhesivas). Quite la vieja placa para pared sólo si todos los cables ya tienen la correspondiente etiqueta.
Termostato programable RTH4300B Quite la placa paredtermostato y coloque la tarjeta de referencia rápida. Acerca de sude nuevo Hale de la parte inferior para quitar el termostato de la placa para pared. Introduzca la tarjeta de referencia luego de montar la placa para pared (consulte las instrucciones de montaje en la página 11).
Guía de instalación Marque la posición de montaje de la placa para pared 1. Hale los cables a través de la placa para pared. 2. Nivele la placa de pared si lo desea (coloque el nivel a lo largo de las lengüetas). 10 3. Marque las posiciones de ambos orificios.
Termostato programable RTH4300B Acerca de Coloque la su placa nuevo para termostato pared 1. Realice los agujeros en los lugares marcados con lápiz: agujeros de 3/16” para tablarroca y agujeros de 7/32” para yeso. 2. Use el martillo para introducir lasanclas en los agujeros hasta que queden a ras de la pared. 3. Coloque la placa para pared sobre las anclas de expansión e introduzca los tornillos. Controle el nivel y ajuste los tornillos.
Guía de instalación Acerca dede Conexión sulos nuevo cables termostato (instalación típica) 1. Una cada uno de los cables etiquetados con el terminal que tenga la misma letra. Quite el puente metálico si cuenta con los cables R y Rc. 2. Use un destornillador para desajustar los terminales de tornillo, introduzca los cables y luego ajuste los tornillos. 3. Coloque el excedente de cable en el interior de la abertura de la pared.
Termostato programable RTH4300B Conecte lossu cables (designaciones Acerca de nuevo termostato de cables menos comunes) Si las etiquetas no coinciden con las letras del termostato, controle el cuadro de la derecha y conecte el terminal como se ilustra aquí (vea las notas a continuación). En caso de conectar los cables tanto al terminal R como al Rc, quite el puente metálico (vea la página 11). No use los cables C, X, ni B. Coloque cinta aisladora en los extremos desnudos del cable.
Guía de instalación Acerca las Instale de su baterías nuevo termostato Coloque dos baterías AA alcalinas en la parte posterior del termostato. Luego de la instalación, las baterías podrán reemplazarse sin necesidad de quitar el termostato de la pared (vea el Manual de funcionamiento para obtener más información).
Termostato programable RTH4300B Acercade Ajuste defuncionamiento su nuevo termostato del ventilador Fije el interruptor para su sistema: F: Para los sistemas de calefacción a gas o aceite, deje el interruptor de fun-cionamiento del ventilador en la posición original de fábrica (esta posición es para los sistemas que controlan el ventilador cuando hay demanda de calefacción). E: Cambie el interruptor a esta posición para los sistemas de calefacción eléctricos o de bombeo de calor.
Guía de instalación Monte termostato el suministro de energía eléctrica Acercaelde su nuevoy reanude termostato 1. Alinee las 4 lengüetas de la placa para pared con las ranuras de la parte posterior del termostato y presione levemente hasta que el termostato encaje en su lugar. Placa para pared 2. Corte la electricidad del sistema de calefacción y refrigeración, o del panel del interruptor de circuito/fusible.
Termostato programable RTH4300B Configuración Acerca de su nuevo del sistema termostato (configure el termostato a fin de que se corresponda con su sistema) Luego, debe fijar el termostato para controlar el sistema de calefacción y enfriamiento de su hogar. Mantenga presionados los botones s y t para introducir la programación del sistema. Número de función Configuración 1 Para comenzar, mantenga presionados los botones s y t hasta que el indicador cambie.
Guía de instalación Acerca de Función 1: su Tipo nuevo de sistema termostato 1 Setup 0 Presione los botones t para seleccionar el tipo de sistema de control de clima de su hogar: 0 Calefacción y refrigeración: Sistema de calefacción a gas, a aceite o eléctrico con aire acondicionado. 1 Bomba de calor: El compresor externo suministra calor y frío. Presione para cambiar los ajustes. Cuando finalice, presione para avanzar hasta la siguiente función.
Termostato programable RTH4300B Acerca de Función 5: su Velocidad nuevo termostato del ciclo térmico 5 Setup 5 Presione para cambiar los ajustes. Cuando finalice, presione para avanzar hasta la siguiente función. Presione los botones t para seleccionar el sistema de calefacción y optimizar la operación: 5 Sistemas de calefacción a gas o a aceite: Use esta configuración si tiene un sistema de calefacción a gas o a aceite estándar de menos de un 90% de efectividad.
Guía de instalación Acerca de Función 14:suVisor nuevo determostato la temperatura 14 Setup 0 Presione los botones t para optar entre visualizar la temperatura en grados Fahrenheit o en grados Celsius: 0 Visualización de la temperatura en Fahrenheit (°F) 1 Visualización de la temperatura en Celsius (°C) Presione para cambiar los ajustes. Cuando haya terminado pulse el botón de activación o pulse y mantenga presionados los botones s y t para salir y guardar los cambios.
Termostato programable RTH4300B Acerca En casode desu inconvenientes nuevo termostato Si tiene dificultades con el termostato, intente seguir las sugerencias que se indican a continuación. La mayoría de los problemas pueden corregirse rápida y fácilmente. El indicador está en blanco • Controle el interruptor de circuito y, si es necesario, reinícielo. • Asegúrese de que los interruptores eléctricos de calefacción y enfriamiento estén encendidos.
Guía de instalación Acerca En casode desu inconvenientes nuevo termostato Los ajustes de la temperatura no cambian Asegúrese de que las temperaturas de calefacción y enfriamiento esté dentro de los rangos aceptables: • Heat: de 40 °F a 90 °F (de 4,5 °C a 32 °C). • Cool: de 50 °F a 99 °F (de 10 °C a 37 °C). El mensaje “Cool On” o “Heat On” titila • La función de protección del compresor está funcionando. Espere 5 minutos para que el sistema se vuelva a iniciar de forma segura, sin dañar el compresor.
Termostato programable RTH4300B Acercaaldecliente Ayuda su nuevo termostato Hale de la parte inferior para quitar el termostato de la placa para pared. Voltee el termostato para encontrar el número de modelo y el código de fecha. Para obtener asistencia relacionada con este producto, visite http://yourhome.honeywell.com. O llame gratis al servicio de atención al cliente de Honeywell, al 1-800-468-1502. Para ahorrar tiempo, anote el número de modelo y el código de fecha antes de llamar.
Guía de instalación Acerca delimitada Garantía su nuevo determostato 1 año Honeywell garantiza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricación o de los materiales, a partir de la fecha de compra por parte del consumidor. Si en cualquier momento durante el período de garantía se verifica que el producto tiene un defecto o que funciona mal, Honeywell lo reparará o reemplazará (a elección de Honeywell).
Termostato programable RTH4300B Acerca delimitada Garantía su nuevo de termostato 1 año DAÑO DE NINGUN TIPO, INCLUIDO EL DAÑO INCIDENTAL O INDIRECTO DERIVADO, DIRECTA O INDIRECTAMENTE, DEL INCUMPLIMIENTO DE LAS GARANTIAS, EXPRESAS O IMPLICITAS, O DE OTRAS FALLAS DE ESTE PRODUCTO. Algunos estados no permiten la exclusión o limitación del daño incidental o indirecto, entonces, esta limitación puede no resultar aplicable a su caso.
Sistemas para automatización y control Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V4Z9 http://yourhome.honeywell.com Impreso en los EE. UU., en papel reciclado que contiene por lo menos un 10% de fibras de papel reciclable. ® Marca registrada de los EE. UU. © 2006, Honeywell International Inc. 69-1772ES M.S.