Quick Installation Guide RTH6400 Series Programmable Thermostat 69-2210EF-03
Installation is Easy Label wires and remove your old thermostat Install and wire your new thermostat Set your new thermostat to match your heating/cooling system – It is preset for the most common system We are here to help. Call 1-800-468-1502 for wiring assistance before returning the thermostat to the store.
1 Turn Off Power to Heating/ Cooling System M28097 1 69-2210EF—03
2 Remove Old Thermostat Remove old thermostat but leave wallplate with wires attached. Leave wallplate in place Is there a sealed tube containing mercury? If so, see back cover for proper disposal instructions.
3 Label Wires with Tags Label the wires using the supplied wire labels as you disconnect them.
4 Separate Wallplate from New Thermostat Remove battery holder. Pull here to remove wallplate from new thermostat.
5 Insert Quick Reference Card Insert quick reference card into slot in back of thermostat.
6 Mount Wallplate Mount the new wallplate using the included screws and anchors. M28345 Drill 3/16-in. holes for drywall Drill 3/32-in.
7 Connect Wires Simply match wire labels. Remove metal jumper if you have both R and Rc wires. M27513 Labels don’t match? See page 21. Have a Heat Pump system? See page 14. We are here to help. Call 1-800-468-1502 for wiring assistance.
8 Install Batteries Install two AA alkaline batteries.
9 Install Thermostat onto Wallplate Install thermostat onto the wallplate on the wall.
10 Turn Power Back On Turn the power back on to the heating/cooling system.
11 If your system type is... If your system type is: q Single Stage Heat and Cool Congratulations, you’re done! If your system type is: q Heat Pump* without Backup Heat q Heat Only q Cool Only Continue with advanced installation on page 13 to match your thermostat to your system type. *Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.
Advanced Installation System setup.......................................................................13 Wiring...................................................................................21 Troubleshooting...................................................................22 Customer assistance..........................................................25 Limited warranty..................................................................
RTH6400 About your System setup new thermostat Press and hold the s and FAN buttons until the screen changes (approximately 5 seconds). SETUP WIRING M28348 ASSISTANCE Press s or t to change settings. Function Setting 1 Next M28349 Press DONE to exit and save settings. Press NEXT to advance to next function.
Advanced Installation Guide Function 1: System type SETUP Press the s or t button to select the type of system you have in your home: WIRING 1 0 Done Next M28350 1 Heat pump: Outside compressor provides both heating and cooling. 2 Heating only: Gas, oil or electric heating without central air conditioning. 3 Heating only with fan: Gas, oil or electric heating without central air conditioning. (Use this setting if you could turn the fan on and off with a fan switch on your old thermostat.
RTH6400 Function 2: Heat pump changeover valve Press the s or t button to select whether your changeover valve is used in heating or cooling: 0 Done WIRING 2 SETUP NOTE: If Function 2 does not appear, please turn to the next page to continue. Next 1 Heating changeover valve: Use this setting if you connected a wire labeled “B” to the O/B W wire terminal (see page 21). TROUBLESHOOTING Press to change setting. When correct setting is selected, press NEXT to display next function.
Advanced Installation Guide Function 3: Heating fan control NOTE: If Function 3 does not appear, please turn to the next page to continue. 3 WIRING SETUP Press the s or t button to select your heating system and fan operation: 0 Done Next TROUBLESHOOTING ASSISTANCE M28353 0 Gas or oil heat: Use this setting if you have a gas or oil heating system (system controls fan operation). 1 Electric heat: Use this setting if you have an electric heating system (thermostat controls fan operation).
RTH6400 Function 5: Heating cycle rate Press the s or t button to select your heating system and optimize its operation: 5 SETUP NOTE: If Function 5 does not appear, please turn to the next page to continue. 5 WIRING Done Next M28354 9 Electric furnace: Use this setting if you have any type of electric heating system. ASSISTANCE 5 Gas or oil furnace: Use this setting if you have a standard gas or oil furnace that is less than 90% efficient.
Advanced Installation Guide Function 12: Manual/Auto Changeover SETUP Press the s or t button to select Manual or Auto Changeover: 12 0 WIRING Done Next M28355 1 Automatic Changeover: (Heat/Off/Cool/Auto) Automatically turns on heat or cool based on room temperatures. CAUTION: To avoid possible compressor damage, set to option 0 if the outside temperature drops below 50ºF (10ºC). NOTE: System maintains a minimum 3ºF difference between heat and cool settings.
RTH6400 Function 13: Smart Response Technology ® Press the s or t button to select Smart Response Technology: ® 1 Next M28356 WIRING Done SETUP 13 1 Smart Response® Technology ON 0 Smart Response® Technology OFF TROUBLESHOOTING Press to change setting. When correct setting is selected, press NEXT to display next function. M28351 19 ASSISTANCE NOTE: See Operating Manual for information on Smart Response® Technology.
Advanced Installation Guide About your Function 14:new Temperature thermostatdisplay SETUP Press the s or t button to select Fahrenheit or Celsius temperature display: 14 0 WIRING Done Next M28357 0 Fahrenheit temperature display (°F) TROUBLESHOOTING ASSISTANCE 1 Celsius temperature display (°C) Press to change setting. When correct setting is selected, press DONE to exit and save changes.
RTH6400 Wiring SETUP If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (see notes, below). WIRING ASSISTANCE M28418 Do not connect both O and B if you have a heat pump. Connect O wire to O/B W. Wrap B wire with electrical tape and do not use. Do not use C, X or B. Wrap bare end of wire with electrical tape. 21 69-2210EF—03 TROUBLESHOOTING If wires will be connected to both R and Rc terminals, remove metal jumper (see page 6).
Advanced Installation Guide Display is blank • Make sure fresh AA alkaline batteries are correctly installed (see page 7). Temperature Make sure heating and cooling settings do not temperatures are set to acceptable ranges: change • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). Cannot change • Check Function 1: System Type to make sure it is set to match your system setting heating and cooling equipment to Cool (see page 14).
RTH6400 Troubleshooting 69-2210EF—03 TROUBLESHOOTING 23 ASSISTANCE Heat pump • Check Function 2: Heat Pump Changeover Valve to make sure issues cool air it is properly configured for your in heat mode, system (see page 15). or warm air in cool mode WIRING “Cool On” or “Heat On” is flashing • Press SYSTEM button to set system to Cool. Make sure the temperature is set lower than the Inside temperature. • Check circuit breaker and reset if necessary.
Advanced Installation Guide Heating • Check Function 1: System Type to make sure it is set to match your and cooling heating and cooling equipment equipment (see page 14). running at the same time (or • Grasp and pull thermostat away heat does not from wallplate. Check to make sure turn off) bare wires are not touching each other (see page 6). Heating system • Check Function 1: System Type to make sure it is set to match your is running in heating and cooling equipment cool mode (see page 14).
RTH6400 About yourassistance Customer new thermostat SETUP For assistance with this product, please visit http://DIYthermostats.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502. To save time, please remove the battery holder and note your model number and date code before calling. To order, please call Honeywell Customer Care toll-free at 1-800-468-1502. WIRING Accessories/replacement parts Battery holder............................... Part No.
1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
27 69-2210EF—03
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal. CAUTION: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C). Automation and Control Solutions Honeywell International Inc.
Guide d’installation rapide Série RTH6400 Thermostat programmable 69-2210EF-03
L’installation est facile ! Étiquetage des fils et retrait de l’ancien thermostat Installation et raccordement du nouveau thermostat Configuration du nouveau thermostat pour correspondre à votre système de chauffage/ climatisation – Il est préréglé en prévision des systèmes les plus communs Nous sommes à votre service. Composer le 1-800-4681502 pour obtenir de l’aide au raccordement avant de retourner le thermostat au magasin.
1 Couper le courant du système de chauffage/de climatisation M28097 1 69-2210EF—03
2 Retirer l’ancien thermostat Enlever le couvercle et le thermostat, mais laisser la plaque murale et les fils en place. Laisser la plaque de montage en place Y a-t-il une ampoule contenant du mercure? Si c’est le cas, se reporter aux consignes figurant sur la couverture avant de ce livret pour connaître les règlements concernant l’élimination.
3 Étiqueter les fils Étiqueter les fils à l’aide des étiquettes fournies à mesure que les fils sont débranchés.
4 Séparer la plaque murale du nouveau thermostat Retirer le porte-piles. Tirer ici pour enlever la plaque murale du thermostat neuf.
5 Insérer la carte de référence rapide Insérer la carte de référence rapide dans la fente à l’arrière du thermostat.
6 Installer la plaque Installer la nouvelle plaque murale à l’aide des vis et des chevilles d’ancrage fournies.
7 Raccorder les fils Il suffit ensuite de faire correspondre les fils avec les étiquettes. Retirer le cavalier en métal s’il y a à la fois les fils « R » et « Rc ». NON UTILISÉ MF27513 Les étiquettes ne correspondent pas? Voir page 21. Avez-vous une thermopompe? Voir pages 14. Nous sommes à votre service. Composer le 1-800-468-1502 pour obtenir de l’aide au cours du raccordement.
8 Installer les piles Installer 2 piles alcalines AA à l’arrière du thermostat.
9 Fixer le thermostat à la plaque murale Installer le thermostat sur la plaque murale fixée au mur.
10 Rétablir l’alimentation électrique Rétablir l’alimentation électrique du système de chauffage-refroidissement.
11 Si votre système est du type suivant... Si votre système est du type suivant : q Chauffage et refroidissement à un étage Félicitations, vous avez terminé! Si votre système est du type suivant : q Thermopompe* sans chauffage d’appoint q Chauffage seulement q Refroidissement seulement Passer au mode d’installation avancé à la page 13 pour faire correspondre le thermostat à votre type de système.
Guide d’installation avancé Configuration du système...................................................13 Câblage................................................................................21 Dépannage..........................................................................22 Assistance à la clientèle.....................................................25 Garantie limitée...................................................................
RTH6400 Configuration du système RÉGLAGE Pour commencer, appuyer sur les touches s et FAN et les maintenir enfoncées jusqu’à ce que l’affichage change. WIRING M28348 s ou t pour modifier les réglages. Fonction Réglage 1 0 Next M28349 Appuyer sur DONE pour quitter la configuration et enregistrer les réglages. Appuyer sur NEXT pour passer à la fonction suivante.
Guide d’installation avancé 1 WIRING RÉGLAGE About your Fonction 1 :new Typethermostat de système Appuyer sur les touches s ou t pour sélectionner le type de système à la maison : 0 Done Next TROUBLESHOOTING ASSISTANCE M28350 0 Chauffage et climatisation : Chauffage au gaz, au mazout ou à l’électricité avec climatisation centrale. 1 Thermopompe : Un compresseur extérieur fournit le chauffage et la climatisation.
RTH6400 Fonction 2 : Vanne d’inversion de thermopompe REMARQUE : Si la fonction 2 n’apparaît pas, voir la page suivante pour continuer. 0 Done WIRING 2 RÉGLAGE Appuyer sur les touches s ou t pour choisir si la vanne d’inversion servira au chauffage ou à la climatisation : Next 1 Vanne d’inversion - chauffage : Utiliser ce réglage si le fil marqué «B» a été raccordé à la borne O/B W (page 21). M28351 15 69-2210EF—03 TROUBLESHOOTING Appuyer sur cette touche pour changer le réglage.
Fonction 3 : Commande du ventilateur de chauffage Appuyer sur les touches s ou t pour sélectionner le fonctionnement du système de chauffage et du ventilateur : REMARQUE : Si la fonction 3 n’apparaît pas, voir la page suivante pour continuer. 3 WIRING RÉGLAGE Guide d’installation avancé 0 Done Next 0 Système de chauffage au gaz ou au mazout : Utiliser ce réglage si le système de chauffage est alimenté au gaz ou au mazout (le système commande le ventilateur).
RTH6400 Fonction 5 : Cycle de fonctionnement du système de chauffage 5 5 WIRING Done RÉGLAGE Appuyer sur les touches s ou t pour sélectionner le système de chauffage et optimiser son fonctionnement : REMARQUE : Si la fonction 5 n’apparaît pas, voir la page suivante pour continuer. Next M28354 M28351 17 69-2210EF—03 TROUBLESHOOTING Appuyer sur cette touche pour changer le réglage. Lorsque le réglage voulu est sélectionné, appuyer sur NEXT pour afficher la fonction suivante.
Guide d’installation avancé Appuyer sur s ou t pour sélectionner la commutation manuelle ou automatique : 12 0 Done WIRING RÉGLAGE Fonction 12 : Commutation chaud-froid manuelle/automatique Next M28355 1 Commutation automatique : (Heat/Off/Cool/Auto) Met automatiquement en marche le chauffage ou le refroidissement en fonction de la température ambiante. MISE EN GARDE : Pour éviter d’endommager le compresseur, régler à l’option 0 si la température extérieure devient inférieure à 10 ºC (50 ºF).
RTH6400 Fonction 13 :new Technologie Smart Response About your thermostat ® Appuyer sur s ou t pour sélectionner la technologie Smart Response : ® 1 Next M28356 WIRING Done RÉGLAGE 13 1 Technologie Smart Response EN MARCHE ® 0 Technologie Smart Response À L’ARRÊT ® M28351 19 69-2210EF—03 TROUBLESHOOTING Appuyer sur cette touche pour changer le réglage. Lorsque le réglage voulu est sélectionné, appuyer sur NEXT pour afficher la fonction suivante.
Guide d’installation avancé 14 0 Done WIRING RÉGLAGE About your thermostat Fonction 14 :new Affichage de la température Appuyer sur les touches s ou t pour choisir d’afficher la température en Fahrenheit ou en Celsius : Next M28357 0 Affichage de la température en Fahrenheit (°F) TROUBLESHOOTING ASSISTANCE 1 Affichage de la température en Celsius (°C) Appuyer sur cette touche pour changer le réglage.
RTH6400 About your new thermostat Câblage ou ou ou ou ou SETUP Si les étiquettes ne correspondent pas aux bornes, les raccorder comme l’indique l’explication ci-dessous (voir les notes ci-dessous). ou CÂBLAGE Ne pas raccorder MF28418 ASSISTANCE NON UTILISÉ Si des fils seront raccordés aux bornes R et Rc, enlever le cavalier en métal (page 6). Ne pas se servir de C, X ou B. Enrouler du ruban isolant sur le bout dénudé du fil.
Guide d’installation avancé Rien n’apparaît • S’assurer que les piles alcalines AA ont été bien installées (voir page 7).
RTH6400 Dépannage Appuyer sur la touche SYSTEM pour régler le système à Heat. S’assurer que la température réglée est supérieure à la température intérieure. 23 69-2210EF—03 TROUBLESHOOTING Les voyants • La fonction de protection du compresseur est activée. Attendre « Cool On » ou 5 minutes que le système « Heat On » redémarre en toute sécurité, sans clignotent endommager le compresseur. DÉPANNAGE • S’assurer que la porte du système de chauffage est bien fermée.
Guide d’installation avancé La • Vérifier la Fonction 2 : Vanne d’inversion de la thermopompe thermopompe pour s’assurer qu’elle est bien envoie de l’air réglée pour votre système (page frais en mode 15).
RTH6400 Dépannage à la clientèle Assistance SETUP Pour obtenir de l’aide sur ce produit Honeywell, veuillez consulter le site http://DIYthermostats.honeywell.com ou vous adresser sans frais aux Services à la clientèle de Honeywell au 1 800 468-1502. Pour gagner du temps, enlever le porte-piles et écrire le numéro de modèle et le code de date avant d’appeler. Pour commander, téléphoner aux Services à la clientèle de Honeywell au 1-800-468-1502. Porte-piles...............................
Garantie limitée de un an Honeywell garantit ce produit, à l’exception des piles, contre tout vice de fabrication ou de matière dans la mesure où il en est fait une utilisation et un entretien convenables, et ce, pour un (1) an à partir de la date d’achat par le consommateur. En cas de défectuosité ou de mauvais fonctionnement pendant la période de garantie, Honeywell remplacera ou réparera le produit (au gré de Honeywell) dans un délai raisonnable.
Garantie limitée de un an LA PRÉSENTE GARANTIE TIENT LIEU DE TOUTES LES AUTRES GARANTIES, EXPRESSES OU TACITES, ET LES GARANTIES DE VALEUR MARCHANDE ET DE CONFORMITÉ À UNE FIN PARTICULIÈRE SONT PAR LES PRÉSENTES EXCLUES APRÈS LA PÉRIODE DE UN AN DE LA PRÉSENTE GARANTIE Certaines provinces ne permettent pas de limiter la durée des garanties tacites et, par conséquent, la présente limitation peut ne pas s’appliquer.
AVIS CONCERNANT LE MERCURE : Si le présent thermostat remplace un thermostat contenant du mercure dans une ampoule scellée, ne pas jeter l’ancien thermostat à la poubelle. Communiquer avec le service local de cueillette des déchets pour obtenir de l’information sur le recyclage ou sur la bonne façon de disposer d’un ancien régulateur contenant un contact à mercure.