User Guide Wi-Fi Programmable Thermostat RTH6500WF Wi-Fi Series
In the box you will find • • • • • • • • Thermostat Wallplate (attached to thermostat) Screws and anchors Quick Start Guide Thermostat ID Card Wire labels User Guide Quick Reference Card 69-2718ES—03 ii
Welcome Congratulations on your purchase of a Honeywell Wi-Fi programmable thermostat. When registered to Honeywell’s Total Connect Comfort Solutions, you can remotely monitor and control the heating and cooling system in your home or business—you can stay connected to your comfort system wherever you go. Honeywell’s Total Connect Comfort is the perfect solution if you travel frequently, own a vacation home, a business or manage an Investment property or if you are simply looking for peace of mind.
This thermostat works with common 24 volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat. MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www. thermostat-recycle.
Table of contents About your new thermostat Controls and Home screen quick reference............................................. 5 Preset energy-saving schedules.................. 6 Installation Installing your thermostat............................. 8 Connecting to your Wi-Fi network.............. 26 Registering your thermostat online............ 31 Operation Setting the clock......................................... 36 Setting the fan............................................
Features of your Wi-Fi thermostat With your new thermostat, you can: • Connect to the Internet to monitor and control your heating/cooling system • View and change your heating/cooling system settings • View and set temperature and schedules • Receive alerts via email and get automatic upgrades Your new thermostat provides: • Smart Response Technology • Compressor protection • Heat/cool auto changeover 69-2718ES—03 4
Controls and home screen quick reference Once your Wi-Fi thermostat is installed, it will display the home screen. Portions of this display will change depending on how you are viewing it. Set up messages describe steps in the Wi-Fi set up process Wi-Fi status HOLD Temperature adjustment buttons Permanent override button M31586 Set clock, day, or schedule Select fan settings Select system mode Additional settings The screen lights when you press any button.
Preset energy-saving schedules This thermostat is pre-set with energy-saving program settings for four time periods. Using the default settings can reduce your heating/cooling expenses if used as directed. Savings may vary depending on geographic region and usage. To change the settings, see pages 39–41.
Setting up your thermostat Setting up your Wi-Fi programmable thermostat is easy. It is preprogrammed and ready to go as soon as it is installed and registered. 1 Install your thermostat. 2 Connect your home Wi-Fi network. 3 Register online for remote access. Before you begin, you may want to watch a brief installation video. Use the QR Code at the front of this guide, or go to wifithermostat.
Installing your thermostat You might need the following tools to install this thermostat: • • • • o. 2 Phillips screwdriver N Small pocket screwdriver Pencil Level (optional) • D rill and bits (3/16” for drywall, 7/32” for plaster) (optional) • Hammer (optional) • Electrical tape (optional) 1 Switch OFF power to your heating/cooling system. or Important! To protect your equipment, switch OFF the power to your heating/ cooling system at the breaker box or the system switch.
Installing your thermostat 2 Remove old thermostat faceplate and leave wires connected. 2a Take a picture of the wire connections for later reference. 2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at wifithermostat.com/videos Important! C wire is required and is the primary power source for your thermostat. Without a C wire, your thermostat will not power up.
Installing your thermostat 3 Label wires. Do not label by wire color. Use the supplied sticky tags to label each wire as you disconnect it. Label wires according to the old thermostat terminal designations, not by wire color. Sticky tags Blank sticky tags Note: If no tag matches a wire terminal label, write the terminal label on a blank tag. 4 Remove wallplate. Remove the old wallplate from the wall after all wires have been labeled and disconnected.
Installing your thermostat 5 Separate Wi-Fi thermostat and its wallplate. On your new thermostat, grasp the finger holds on the top and bottom of the wallplate with one hand and the thermostat (front) with the other hand. Pull pieces apart.
Installing your thermostat 6 Mount wallplate for Wi-Fi thermostat. Mount your new wallplate using screws and anchors included with the thermostat. If necessary: Wallplate Drill 3/16-in holes for drywall. Drill 7/32-in holes for plaster. Note: You may be able to use your existing wall anchors. Hold the wallplate up to the existing anchors to check for alignment.
Installing your thermostat Important! The Wi-Fi thermostat requires a C wire to operate. The C, or common, wire brings 24 VAC power to the thermostat. Many older mechanical or battery operated thermostats do not require a C wire. If you don’t have a C wire, try: • Looking for an unused wire that is pushed into the wall. Connect that wire to C and check that it is connected to the 24 VAC common at your heating/cooling system. Note: Not all heating/cooling systems label the 24 VAC common C.
Installing your thermostat Wiring (conventional system) Remove metal jumper only if you have both 7A Wire the Wi-Fi thermostat to your conventional system. R and RC wires a Starting with the C Wire, match the sticky tag on the wire to the terminal labels. You must have a C wire. See page 13. b Loosen screw, insert wire on inside edge G W C Y of terminal, then tighten screw. R K Y2 W2 G W C Y R RC CONVENTIONAL c Verify wire is firmly secured by gently pulling on wire.
Installing your thermostat Wiring (heat pump system only) Labels don’t match? See alternate wiring key on pages 18–19. 7B Wire Wi-Fi thermostat to your heat pump. a Starting with the C Wire, match the sticky tag on the wire to the terminal labels. You must have a C wire. See page 13. b Loosen screw, insert wire on inside edge of terminal, then tighten screw. c Verify wire is firmly secured by gently G O Y R Aux pulling on wire. d Repeat steps a–c for all other wires.
Installing your thermostat Alternate wiring (conventional system) Use this if your wire labels don’t match the terminal labels. 2 Y2 W2 G Note: You must have a C wire or equivalent. See page 13. W F C W1 H X B C1 Y Y1 M R RH 4 V RC R 1 K Y2 W2 G W C Y R RC CONVENTIONAL 3 MCR33885 See key to 1 – 3 on page 17.
Installing your thermostat Alternate wiring key (conventional system) 1 Do not use K terminal. For future use. 2 If your old thermostat had both R and RH wires, remove metal jumper. Connect the R wire to the RC terminal, and the RH wire to the R terminal. 3 Remove metal jumper connecting R and RC only if you must connect both R and RC.
Installing your thermostat Alternate wiring (heat pump system only) Use this if your wire labels don’t match the terminal labels. 3 2 Note: You must have a C wire or equivalent. See page 13. L E AUX F X X2 W W1 W2 G 4 4 5 6 O C Y R F H B X B Y1 M V VR RC R 1 7 K L AUX/E G O/B C Y R RC HEAT PUMP MCR33886 69-2718ES—03 18 See key to 1 – 7 on page 19.
Installing your thermostat Alternate wiring key (heat pump system only) 1 Do not use K terminal. For future use. 2 If old thermostat has separate wires on AUX and E, place both wires into the E/AUX terminal. If old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No jumper is required. 3 If your old thermostat had an O wire and not a B wire, attach the O wire to the O/B terminal. 4 If your old thermostat had separate O and B wires, attach the B wire to the C terminal.
Installing your thermostat 8 Insert quick reference card. Quick reference card Fold quick reference card along score lines, and slide it into the slot on the back of the thermostat.
Installing your thermostat 9 Attach thermostat to wallplate. Align the thermostat to the wallplate and then snap into place.
Installing your thermostat 10 Switch heating/cooling system ON. Important! 10a Verify that the C wire is connected at the thermostat and at the heating/cooling system. or 10b Make sure the heating/ cooling system door is firmly secured. 10c Switch power back ON for your heating/cooling system at the breaker box or its power switch.
Installing your thermostat 11 Set clock to current day and time. 11a Press s or t to set clock. 11b Press Set Day. HOLD 11c Press s or t to select the day of week. 11d Press Done to save. MCR33908 (Press and hold a st button to quickly change a setting.
Installing your thermostat 12 Determine your heating/cooling system type. Important! Heating/cooling system type must be set so that your thermostat operates properly and does not damage your system. 12a If your system type is conventional single stage (natural gas-powered single stage with a/c), continue to “Connecting to your Wi-Fi network” on page 26.
Installing your thermostat Congratulations! Your thermostat is operational. 13 Test your thermostat 13a Press the System button to change to heating or cooling and begin operation. 13b For remote access to your thermostat, continue to “Connecting to your Wi-Fi network” on page 26. MCR33880 Heating/cooling system not turning on? Refer to page 62 or FAQ at wifithermostat.
Connecting to your Wi-Fi network To complete this process, you must have a wireless device connected to your home wireless network. Any of these device types will work: • Tablet (recommended) • Laptop (recommended) • Smartphone If you get stuck... at any point in this procedure, restart the thermostat by removing the thermostat from the wallplate, wait for 10 seconds, and snap it back onto the wallplate. Go to Step 1 in this procedure, starting on page 27.
Connecting to your Wi-Fi network 1 Connect to your thermostat. 1a Make sure the thermostat displays Wi-Fi Setup. 1b On the wireless device (laptop, tablet, smartphone), view the list of available Wi-Fi networks. 1c Connect to the network called NewThermostat_123456 (the number will vary). HOLD M33852 Note: If you are asked to specify a home, public, or office network, select Home Network.
Connecting to your Wi-Fi network 2 Join your home network. 2a Open your web browser to access the Thermostat Wi-Fi Setup page. The browser should automatically direct you to the correct page; if it does not, go to http://192.168.1.1 2b Find the name of your home network on this page and select it. 2c Complete the instructions for joining your Wi-Fi network and click on the Connect button. (Depending on your network setup, you may see an instruction such as Enter Password for your home network.
Connecting to your Wi-Fi network Note: If your Wi-Fi network does not appear in the list on the Thermostat Wi-Fi Setup page: • Try performing a network rescan by pressing the Rescan button. This is helpful in areas with a lot of networks. • If you are connecting to a hidden network, then enter the network SSID in the textbox, select the encryption type from the drop down menu, and click on the Add button. This manually adds the network to the top of the list.
Connecting to your Wi-Fi network 3 Make sure your thermostat is connected. While the connection is in process, your thermostat will flash Wait for up to 3 minutes. When the connection is complete, the display will show Wi-Fi Setup Connection Success. The Wi-Fi signal strength will appear in the top-right corner. M33875 After about 60 seconds, the home screen will appear and Register at Total Connect will flash until registration is complete. If you don’t see these messages, see page 26.
Registering your thermostat online To view and set your Wi-Fi thermostat remotely, you must have a Total Connect Comfort account. Use the following steps. 1 Open the Total Connect Comfort web site. Go to mytotalconnectcomfort.com M31570 View the Wi-Fi Thermostat Registration video at wifithermostat.
Registering your thermostat online If you have an account, click Login – or – click Create An Account. 2a Follow the instructions on the screen. 2b Check your email for an activation message from My Total Connect Comfort. This may take several minutes. Note: If you do not receive a response, check your junk mailbox or use an alternate e-mail address. 2c Follow activation instructions in the email. 2d Log in. 69-2718ES—03 32 M31571 2 Login or create an account.
Registering your thermostat online 3 Register your Wi-Fi thermostat. After you are logged in to your Total Connect Comfort account, register your thermostat. 3a Follow the instructions on the screen. After adding your thermostat location, you must enter the thermostat’s unique identifiers: • MAC ID • MAC CRC Note: These IDs are listed on the Thermostat ID Card included in the thermostat package. The IDs are not case sensitive.
Registering your thermostat online 3b When the thermostat is successfully registered, the Total Connect Comfort registration screen will display a SUCCESS message. In the thermostat display, you will see Setup Complete for about 90 seconds.
Registering your thermostat online 3c Also notice that your thermostat displays its signal strength. Congratulations! You’re done. You can now control your thermostat from anywhere through your tablet, laptop, or smartphone Total Connect Comfort free app is available for Apple iPhone , iPad and iPod touch devices at iTunes or at Google Play for all Android™ devices.
Setting the time and day 1 Press Set Clock/Day/Schedule, then press s or t to set clock. 2 Press Set Day, then press s or t to select the day of week. HOLD 3 Press Done to save. Note: If the Set Clock/Day/Schedule option is not displayed, press Done. Note: If the display flashes Set Clock, the thermostat will follow your settings for the Monday “Wake” time period until you reset the time and day.
Setting the fan Press Fan to select On or Auto (toggle to re-select). Auto: Fan runs only when the heating or cooling system is on. Auto is the most commonly used setting. On: Fan is always on. MCR33895 Note: Options may vary depending on your heating/cooling equipment.
Selecting system mode Press System to select: Heat: Controls only the heating system. Cool: Controls only the cooling system. Off: Heating/cooling systems are off. Auto: Selects heating or cooling depending on the indoor temperature. Em Heat (heat pumps with aux. heat): Controls auxiliary/emergency heat. Compressor is off. 69-2718ES—03 38 MCR33880 Note: Depending on how your thermostat was installed, you may not see all system settings.
Adjusting program schedules 1 Press Set Clock/Day/Schedule, then Set Schedule. 2 Press s or t to set your Monday (Mon) Wake time, then press Next. 3 Press s or t to set the temperature for this period, then press Next. 4 Set time and temperature for the next time period (Leave). Repeat Steps 2 and 3 for each time period. 5 Press Next to set time periods for the next day. Repeat Steps 2 through 4 for each day. 6 Press Done to save and exit.
Overriding schedules temporarily Press s or t to immediately adjust the temperature. The new temperature will be maintained only until the next programmed time period begins. To cancel the temporary setting at any time, press Cancel. The program schedule will resume.
Overriding schedules permanently 1 Press HOLD to permanently adjust the temperature. This will turn off the program schedule. 2 Press s or t to adjust the temperature setting.
Unregistering thermostat If you remove the thermostat from your Total Connect Comfort website account (for example, you’re moving and leaving the thermostat behind), the thermostat will display Register at Total Connect until it is re-registered.
Disconnecting Wi-Fi Replacing your router If you disconnect the thermostat from your Wi-Fi network: 1 Enter system setup (see page 48). 2 Change setting 39 to 0 (see page 54). The screen will display Wi-Fi Setup. M33855 Re-connect to a Wi-Fi network by following the steps on page 26. Turning Wi-Fi off If you do not plan to control the thermostat remotely, you can remove the Wi-Fi Setup message from the screen: 1 Enter system setup (see page 48). 2 Change setting 38 to 0 (see page 54).
Software updates Honeywell periodically issues updates to the software for this thermostat. The updates occur automatically through your Wi-Fi connection. All your settings are saved, so you will not need to make any changes after the update occurs. While the update is taking place, your thermostat screen flashes Updating and shows the percentage of the update that has occurred. When the update is complete, your home screen will appear as usual.
Smart Response Technology This feature allows the thermostat to “learn” how long the heating/cooling system takes to reach programmed temperature settings, so the temperature is reached at the time you set. For example: Set the Wake time to 6:00 am, and the temperature to 70°. The heat will come on before 6:00 am, so the temperature is 70° by 6:00 am. Note: System setting function 13 controls Smart Response Technology. See “Smart Response Technology” on page 52.
Compressor protection This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage. M33882 The message Cool On (or Heat On for a heat pump) will flash during the wait time.
Auto changeover This feature is used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. MCR33893 Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation. Note: System setting function 12 controls Auto changeover. See “Manual/Auto Changeover” on page 51.
Setting functions and options You can change options for a number of system functions. Available functions depend on the type of system you have. The functions, along with available options, are described on pages 50–54. This thermostat is pre-set for a single-stage heating/cooling system. Setting function 1 for a heat pump will adjust the default settings.
Setting functions and options 1 Press Fan and s simultaneously and hold for approximately 3 seconds. The screen will change to display two numbers and the button designations will be Done, Back, blank, Next. 2 Press Next until you see the function number—the larger number on the left— you want to set. 3 Change options for any function by pressing s or t until the correct option (smaller number on right) is displayed. 4 Repeat Steps 2 and 3 until you have set all functions that you wish to change.
System setup (See page 48 for instructions.) Function 1 Select System Type If you are not sure of your heating/ cooling system type or have other questions, go to wifithermostat.com Settings & Options 0 1 2 3 4 5 6 7 8 2 Heat Pump Changeover Valve (for heat pumps only) 0 1 Heat/cool: Gas, oil or electric heating with central air conditioning. Heat pump: Heat pump without backup or auxiliary heat. Heat only: Gas, oil or hot water heat without central air conditioning.
System setup (See page 48 for instructions.) Function Settings & Options Heating Fan Control 0 5 Heating Cycle Rate 6 Heating Cycle Rate Stage 2 5 9 3 3 12 Manual/Auto Changeover See page 47 for more information. 1 1 0 1 Gas or oil heat: Use this setting if you have a gas or oil heating system (system controls fan operation). Electric heat: Use this setting if you have an electric heating system (thermostat controls fan operation).
System setup (See page 48 for instructions.) Function Settings & Options 13 Smart Response Technology See page 45 for more information. 1 0 On Off 14 Temperature Format (°F/°C) 0 1 Fahrenheit Celsius 16 Schedule Options 1 0 Program schedule is on (7-day programmable). Program schedule is off. Thermostat can not be programmed.
System setup (See page 48 for instructions.) Function 36 Settings & Options Device Name 52 = Thermostat 1 Basement This name will 2 Bathroom identify the 3 Bathroom 1 thermostat when 4 Bathroom 2 you view it remotely. 5 Bathroom 3 If you register 6 Bedroom multiple thermostats, 7 Bedroom 1 give each one a 8 Bedroom 2 different name.
System setup (See page 48 for instructions.) Function Settings & Options 38 Wi-Fi On/Off 1 0 Wi-Fi is on and can be connected to a Wi-Fi network. Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you are not connecting the thermostat to a Wi-Fi network this will remove the text Wi-Fi Setup from the messaging center. 39 Wi-Fi Connection 1 0 Connected to Wi-Fi network. This is set automatically when the thermostat is connected to the Wi-Fi network.
Frequently asked questions QQ: Will my thermostat still work if I lose my Wi-Fi connection? AA: Yes, the thermostat will operate your heating and/or cooling system with or without Wi-Fi. QQ: How do I find the password to my router? AA: Contact the manufacturer of the router or check the router documentation. QQ: Why am I not seeing my Wi-Fi setup page? AA: You are probably connected only to your router, not to your thermostat. Try connecting to the thermostat again.
Frequently asked questions QQ: Where can I find my MAC ID and MAC CRC codes? AA: The MAC ID and MAC CRC numbers are included on a card packed with the thermostat or on the back of the thermostat (visible when removed from wallplate). Each thermostat has a unique MAC ID and MAC CRC. QQ: My thermostat is unable to register to the Total Connect Comfort website. AA: Verify that the thermostat is correctly enrolled on your home Wi-Fi network.
Frequently asked questions QQ: I registered on the Total Connect Comfort website but was unable to login using my new account. AA: Check your email and ensure that you received an activation email. Follow the instructions to activate your account and then login to the website. QQ: I have signed up on the Total Connect Comfort website and have not received a confirmation email. AA: Check for the email in your Junk or Deleted folder.
Troubleshooting Lost Signal If the no-Wi-Fi indicator displays in place of the Wi-Fi strength indicator in the upper right hand corner of the home screen: • Check another device to be sure Wi-Fi is working in your home; if not, call your Internet Service Provider. • Move the router. • Restart the thermostat: remove it from the wallplate, wait 10 seconds, and snap it back onto the wallplate. Return to Step 1 of Connecting to your Wi-Fi network.
Troubleshooting Error Codes For certain problems, the thermostat screen will display a code that identifies the trouble. Initially, error codes are displayed alone in the time area of the screen; after a few minutes, the home screen is displayed and the code alternates with the time. Error Code M33999 Action E01 During Wi-Fi Setup, the router lost power. • Ensure your router has power. • If trying to connect to a hidden or manually added network, confirm the router has power and is working.
Troubleshooting Error Code E42 Router is not issuing an IP address to the thermostat. Action • Wait for 30 minutes, connection can take several minutes. • If still no connection, remove thermostat from wallplate for 10 seconds, then reconnect it (see page 26). • Verify your router is correctly setup to automatically give IP addresses. E43 No internet connection. • Make sure the Internet cable is plugged in. Thermostat cannot • Reboot the router. communicate to Total Connect Comfort.
Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • Check circuit breaker and reset if necessary. • Make sure power switch at heating and cooling system is on. • Make sure furnace door is closed securely. • Make sure C wire is connected (see page 13).
Troubleshooting Heat pump issues cool air in heat mode, or warm air in cool mode • Check Function 2: Heat Pump Changeover Valve to make sure it is properly configured for your system (see page 50). Heating or cooling system does not respond • Press System to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press System to set system to Cool. Make sure the temperature is set lower than the Inside temperature. • Check circuit breaker and reset if necessary.
Troubleshooting Heating system is running in cool mode • Check Function 1: System Type to make sure it is set to match your heating and cooling equipment (see page 50). Heating and cooling equipment are running at the same time • Check Function 1: System Type to make sure it is set to match your heating and cooling equipment (see page 50). • Grasp and pull thermostat away from wallplate. Check to make sure bare wires are not touching each other. • Check thermostat wiring is correct.
Glossary C wire The “C” or common wire brings 24 VAC power to the thermostat from the heating/cooling system. Some older mechanical or battery operated thermostats may not have this wire connection. It is necessary for establishing a Wi-Fi connection to your home network. Heat Pump heating/cooling system Heat pumps are used to heat and cool a home. If your old thermostat has a setting for auxiliary or emergency heat, you likely have a heat pump.
Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.
Regulatory information Thermostats To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
69-2718ES-05 Automation and Control Systems Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 wifithermostat.com ® U.S. Registered Trademark. Apple, iPhone, iPad, iPod touch and iTunes are trademarks of Apple Inc. All other trademarks are the property of their respective owners. © 2015 Honeywell International Inc. 69-2718ES—05 M.S. Rev. 01-15 Printed in U.S.A.
Guía del usuario Termostato programable con conexión WiFi Serie Red inalámbrica (Wi-Fi) RTH6500WF
En la caja, encontrará lo siguiente: • Termostato • Placa de pared (adherida al termostato) • Tornillos y anclajes • Guía para el encendido rápido • Tarjeta de identificación del termostato • Etiquetas de los cables • Guía del usuario • Tarjeta de referencia rápida 69-2718ES—03 ii
Bienvenido Felicitaciones por la compra del termostato programable con conexión WiFi de Honeywell. Cuando se registre en Total Connect Comfort Solutions de Honeywell, puede supervisar y controlar de manera remota el sistema de calefacción y refrigeración de su hogar o empresa; puede permanecer conectado a su sistema de confort dondequiera que vaya.
Este termostato funciona con sistemas comunes de 24 voltios, como aplicaciones de aire forzado, hidrónicas, de una bomba de calor, de aceite, de gas y eléctricas. No funciona con sistemas de milivoltios, como una chimenea a gas, ni con sistemas de 120/240 voltios, como la calefacción de zócalo eléctrica. AVISO SOBRE MERCURIO: No coloque el termostato existente en la basura si este contiene mercurio en un tubo sellado. Comuníquese con Thermostat Recycling. Corporation en www.thermostat-recycle.
Índice Acerca de su nuevo termostato Referencia rápida de los controles y la pantalla de inicio................................... 5 Cronogramas de ahorro de energía predeterminados............................. 6 Instalación Instalación del termostato............................ 8 Conexión a la red WiFi............................... 26 Registro del termostato en línea................ 31 Funcionamiento Setting the time and day............................ 36 Configuración del ventilador.................
Características del termostato con conexión WiFi Con el nuevo termostato, podrá realizar lo siguiente: • Conectarse a Internet para supervisar y controlar el sistema de calefacción/ refrigeración • Ver y cambiar las configuraciones del sistema de calefacción/refrigeración • Ver y configurar la temperatura y los cronogramas • Recibir alertas por correo electrónico y obtener actualizaciones automáticas El nuevo termostato ofrece lo siguiente: • Tecnología Smart Response • Protección del compresor • Cam
Referencia rápida de los controles y la pantalla de inicio Una vez que el termostato con conexión WiFi esté instalado, podrá visualizar la pantalla de inicio. Partes de esta pantalla cambiarán según cómo la vea.
Cronogramas de ahorro de energía predeterminados Este termostato cuenta con configuraciones del programa de ahorro de energía predeterminadas durante cuatro períodos. Si utiliza las configuraciones predeterminadas, puede reducir los gastos de calefacción/refrigeración, siempre que siga las instrucciones. Los ahorros pueden varias según la región geográfica y el uso. Para cambiar las configuraciones, consulte las páginas 39–41.
Configuración del termostato Configurar el termostato programable es fácil. Está preprogramado y listo para funcionar tan pronto como se instale y se registre. 1 Instale su termostato. 2 Conecte a su red doméstica WiFi. 3 Regístrelo a través de Internet para obtener acceso remoto. Antes de comenzar, le recomendamos que mire un breve video de instalación. Utilice el QR Code en la parte delantera de esta guía o visite wifithermostat.
Instalación del termostato Es posible que necesite las siguientes herramientas para instalar el termostato: • • • • • Destornillador Phillips n.° 2 Destornillador de bolsillo pequeño Lápiz Nivel (opcional) Taladro y brocas (3/16” [4.8 mm] en paneles de yeso, 7/32” [5.5 mm] en yeso) (opcional) • Martillo (opcional) • Cinta aislante (opcional) o 1 DESCONECTE la energía de su sistema de calefacción/refrigeración.
Instalación del termostato 2 Retire el termostato existente. 2a Tome una fotografía de las conexiones de los cables para usar de referencia más adelante. 2b Si ningún cable está conectado al terminal con la marca C o no existe un terminal C en el termostato existente, mire el video Alternate Wiring (Cableado alternativo) en wifithermostat.com/videos ¡Importante! El cable C es necesario y es la principal fuente de energía para su termostato. Sin un cable C, su termostato no encenderá.
Instalación del termostato 3 Etiquete los cables. No etiquete por color del cable. Utilice las etiquetas adhesivas suministradas para identificar cada cable a medida que los desconecta. Etiquete los cables conforme a las designaciones de los terminales del termostato existente, no según el color de los cables. Etiqueta autoadhesiva Etiqueta autoadhesiva en blanco Nota: If si ninguna etiqueta coincide con las demás, etiquete el terminal del cable utilizando una etiqueta en blanco.
Instalación del termostato 5 Separe el termostato con conexión WiFi y la placa de pared. En el nuevo termostato, sostenga, con una mano, la placa de pared desde los orificios de sujeción en la parte superior e inferior y, con la otra, el termostato (frente). Separe las piezas.
Instalación del termostato 6 Monte la placa de pared para termostato con conexión WiFi. Monte la nueva placa de pared con los tornillos y anclajes incluidos con el termostato. Placa de pared Si fuese necesario: Taladre agujeros de 3/16 in (4.8 mm) en paneles de yeso. Taladre agujeros de 7/32 in (5.6 mm) en yeso. Nota: puede usar los tarugos de pared existentes. Sostenga la placa de pared con los tarugos existentes para controlar la alineación.
Instalación del termostato ¡Importante! el termostato con conexión WiFi requiere de un cable C para que funcione. El cable C, o común, le transmite 24 V CA al termostato. Muchos termostatos mecánicos o con batería más antiguos no requieren de un cable C. Si no tiene un cable C, intente hacer lo siguiente: • Busque un cable sin usar que esté introducido en la pared. Conecte ese cable a C y verifique que esté conectado a 24 V CA en el sistema de calefacción/refrigeración.
Instalación del termostato Cableado (sistema convencional) Extraiga el puente de metal solo si tiene cables R y RC. 7A Coloque el cableado del termostato con conexión WiFi en su sistema convencional. a Comience con el cable C y coloque la etiqueta autoadhesiva en el cable con las etiquetas del terminal. Debe tener un cable C. Refiérase a la página 13. b Afloje el tornillo, inserte el cable en el borde interior del terminal, luego, ajuste el tornillo.
Instalación del termostato Cableado (sistema de bomba de calor únicamente) ¿Las etiquetas no coinciden? Consulte la clave para la instalación de cableado alternativo en las páginas 18–19. 7B Coloque los cables del termostato con conexión WiFi a su bomba de calor. a Comience con el cable C y coloque la etiqueta autoadhesiva en el cable con las etiquetas del terminal. Debe tener un cable C. Refiérase a la página 13.
Instalación del termostato Cableado alternativo (sistema convencional) Utilícelo si las etiquetas de los cables no coinciden con las etiquetas de los terminales. 2 Y2 W2 G Nota: debe tener un cable C o equivalente. Refiérase a la página 13. W o o F W1 H C Y o o X B C1 Y1 M R RC o o RH 4 V R 1 K Y2 W2 G W C Y R RC CONVENCIONAL 3 MSCR33885 Consulte las claves de 1 a 3 en la página 17.
Instalación del termostato Clave para cableado alternativo (sistema convencional) 1 No utilice el terminal K. Para uso futuro. 2 Si su termostato existente tenía cables R y RH, extraiga el puente de metal. Conecte el cable R al terminal RC, y el cable RH al terminal R. 3 Retire el puente de metal que conecta los terminales R y RC solo si debe conectar los dos, R y RC.
Instalación del termostato Cableado alternativo (sistema de bomba de calor únicamente) Utilícelo si las etiquetas de los cables no coinciden con las etiquetas de los terminales. 3 2 Nota: debe tener un cable C o equivalente. Refiérase a la página 13. L E AUX o o F X X2 G 4 4 5 6 O C Y R RC o o o o o o o W W1 W2 F H B X B Y1 M V VR R 1 7 K L AUX/E G O/B C Y R RC BOMBA DE CALOR MSCR33886 1 69-2718ES—03 18 Consulte las claves de – 7 en la página 19.
Instalación del termostato Clave para cableado alternativo (sistema de bomba de calor únicamente) 1 No utilice el terminal K. Para uso futuro. 2 Si el termostato existente tiene cables separados en AUX y E, coloque los dos cables en el terminal E/AUX. Si el termostato existente tiene un cable en AUX con un puente conectado a E, coloque el cable en el terminal E/AUX. No necesita un puente. 3 Si su termostato existente tenía un cable O en lugar de un cable B, conecte el cable O al terminal O/B.
Instalación del termostato 8 Inserte la tarjeta de referencia rápida. Doble la tarjeta de referencia rápida en tres partes por las líneas marcadas y deslícela en la ranura entre el termostato y la placa de pared.
Instalación del termostato 9 Conecte el termostato a la placa de pared. Alinee el termostato con la placa de pared y presiónelo para que calce en su lugar.
Instalación del termostato 10 Encienda el sistema de calefacción/ refrigeración. ¡Importante! 10a Verifique que el cable C esté conectado al termostato y al sistema de calefacción/ refrigeración. o 10b Verifique que la puerta del sistemas de calefacción/ refrigeración esté bien cerrada. 10c Vuelva a ENCENDER su sistema de calefacción/refrigeración en la caja de interruptores de circuito o su interruptor de energía.
Instalación del termostato 11 Configure el reloj al día y hora actual. 11a Presione s o t para configurar el reloj. HOLD 11b Presione Set Day. 11c Presione s o t para seleccionar el día de la semana. 11d Presione Done (terminado) para guardar. MCR33908 HOLD (Presione y sostenga un botón st para cambiar una configuración rápidamente.
Instalación del termostato 12 Determine el tipo de sistema de calefacción/refrigeración. ¡Importante! El tipo del sistema de calefacción/refrigeración debe estar configurado para que el termostato funcione correctamente y no dañe el sistema. 12a Si se trata de un sistema convencional de una sola etapa (una sola etapa accionado por gas natural con A/C), continúe con “Conexión a la red WiFi” en la página 26.
Instalación del termostato ¡Felicitaciones! Su termostato ya funciona. 13 Pruebe el termostato 13a Presione el botón System (Sistema) para cambiar a calefacción o refrigeración, e iniciar el funcionamiento. 13b Para acceder de manera remota al termostato, continúe con el “Conexión a la red WiFi” en la página 26. MCR33880 El sistema de calefacción/ refrigeración, ¿no enciende? Consulte la página 62 o las Preguntas frecuentes en wifithermostat.
Conexión a la red WiFi Para completar este paso, debe tener un dispositivo inalámbrico conectado a su red inalámbrica doméstica. Cualquiera de estos tipos de dispositivos funcionará: • Computadora tipo tablet (recomendado) • Computadora portátil (recomendado) • Teléfono inteligente Si no puede continuar... en algún momento durante este procedimiento, reinicie el termostato. Para ello, retírelo de la placa de pared, espere 10 segundos y vuelva a calzarlo en la placa de pared presionándolo.
Conexión a la red WiFi 1 Conecte el termostato. 1a Verifique que el termostato muestre Wi-Fi Setup (configuración de WiFi). 1b Consulte la lista de todas las redes WiFi disponibles en el dispositivo inalámbrico (computadora tipo tablet, computadora portátil o teléfono inteligente). 1c Conéctese a la red denominada NewThermostat_123456 (el número variará). HOLD M33852 Nota: si se le pide que especifique una red doméstica, pública o de oficina, seleccione Red doméstica.
2 Conecte su red doméstica. 2a Abra el explorador de Internet para acceder a la página de configuración WiFi del termostato. El navegador debería dirigirlo, automáticamente, a la página correspondiente; si no lo hace, vaya a http://192.168.1.1 2b Busque el nombre de su red doméstica en esta página y selecciónela. Nota: algunos enrutadores cuentan con funciones mejoradas, como redes huésped; utilice su red doméstica.
Conexión a la red WiFi Nota: si su red WiFi no aparece en la lista de la página de configuración del termostato WiFi: • Pruebe a efectuar nuevamente un escaneo de la red presionando el botón Rescan (Volver a examinar). Esto resulta útil en áreas con mucha cantidad de redes. • Si está conectado a una red oculta, ingrese el SSID (identificador de grupo de servicio) de la red en la casilla de texto, seleccione el tipo de codificación del menú desplegable y pulse en el botón Add (Agregar).
Conexión a la red WiFi 3 Asegúrese de que su termostato esté conectado. Mientras la conexión se encuentra en proceso, su termostato continuará destellando el mensaje Wait (esperar) hasta 3 minutos. Cuando se complete la conexión, la pantalla mostrará Wi-Fi Setup Connection Success (configuración de conexión a WiFi exitosa). La potencia de M33875 la señal de WiFi aparecerá en la esquina superior derecha.
Registro del termostato en línea Para ver y configurar el termostato con conexión WiFi de manera remota, debe tener una cuenta en Total Connect Comfort. Siga los siguientes pasos. 1 Abra el sitio web Total Connect Comfort. Vaya a mytotalconnectcomfort.com M31570 Mire el video Wi-Fi Thermostat Registration (Registro del termostato WiFi) en wifithermostat.
2 Inicie sesión o cree una cuenta. Si tiene una cuenta, haga clic en Login (Iniciar sesión) – O bien – haga clic en Create An Account (Crear una cuenta). 2a Siga las instrucciones en la pantalla. 2b Revise su correo electrónico para verificar si tiene un mensaje de activación de My Total Connect Comfort. Esto puede llevar varios minutos. Nota: si no recibe una respuesta, busque en el buzón de correo no deseado o utilice una dirección de correo electrónico alternativa.
Registro del termostato en línea 3 Registre su termostato con conexión WiFi. Después de que haya iniciado sesión en su cuenta My Total Connect Comfort, registre el termostato. 3a Siga las instrucciones en la Thermostat ID Card pantalla.
Registro del termostato en línea 3b Cuando el termostato se haya registrado correctamente, la pantalla de registro de Total Connect Comfort le mostrará el mensaje SUCCESS (registro exitoso). En la pantalla del termostato, verá Setup Complete (se ha completado la configuración) durante aproximadamente 90 segundos.
Registro del termostato en línea 3c También observe que su termostato muestra la potencia de la señal. Felicitaciones! ¡Ya terminó! Ahora, puede controlar su termostato desde cualquier lugar a través de su computadora portátil, computadora tipo tablet o teléfono inteligente. Existen aplicación gratuitas disponibles para dispositivos Apple iPhone , iPad y iPod touch en iTunes o en Google Play , para todos los dispositivos Android™.
Setting the time and day 1 Presione Set Clock/Day/Schedule (configurar reloj/día/cronograma) y, luego, presione s o t para configurar el reloj. HOLD 2 Presione Set Day (configurar día) y, luego, s o t para seleccionar el día de la semana. 3 Presione Done (terminado) para salir. Nota: si no se muestra la opción Set Clock/Day/ Schedule (configurar reloj/hora/cronograma), presione Done (terminado).
Configuración del ventilador Presione Fan (Ventilador) para seleccionar la opción On (Encendido) o Auto (alterne para volver a seleccionar la opción). Auto: el ventilador funciona solo cuando el sistema de calefacción o refrigeración está encendido. La configuración de uso más frecuente es Auto. MCR33895 On: el ventilador está siempre encendido. Nota: Las opciones pueden variar según el equipo de calefacción/refrigeración.
Selección de la modalidad del sistema Presione System (Sistema) para seleccionar una opción. Heat: controla solo el sistema de calefacción. Cool: controla solo el sistema de refrigeración. Off: se apagan los sistemas de calefacción/ refrigeración. Auto: selecciona la calefacción o la refrigeración según la temperatura interior. Em Heat (bombas de calor con calefacción auxiliar): controla la calefacción auxiliar/de emergencia. El compresor está apagado.
Ajuste de los cronogramas del programa 1 Presione Set Clock/Day/Schedule (configurar reloj/ día/cronograma) y luego, Set Schedule (configurar cronograma). 2 Presione s o t para configurar la hora de despertarse el lunes (Mon) y luego presione Next (siguiente). 3 Presione s o t para configurar la temperatura para este período y luego presione Next (siguiente). 4 Configure la hora y la temperatura para el próximo período (Leave [salir]). Repita los pasos 2 y 3 para cada período de tiempo.
Anulación temporal de los cronogramas Presione s o t para ajustar inmediatamente la temperatura. La nueva temperatura se mantendrá solamente hasta que comience el próximo período programado. Para cancelar la configuración temporal en cualquier momento, presione Cancel (Cancelar). El cronograma del programa se reanudará.
Anulación permanente de los cronogramas 1 Presione HOLD (Mantener) para ajustar permanentemente la temperatura. Esto desactivará el cronograma del programa. 2 Presione s o t para ajustar la temperatura. La temperatura que usted configure se mantendrá las 24 horas del día, hasta que la cambie manualmente o presione Cancel (cancelar) para volver al cronograma programado.
Baja del termostato Si usted retira el termostato de su cuenta en el sitio Web Total Connect Comfort (por ejemplo, si se muda y deja el termostato), el termostato mostrará el mensaje Register at Total Connect (Registar en Total Connect) hasta que se vuelva a registrar.
Desconexión de la red WiFi Cambio de su enrutador Si usted desconecta el termostato de su red WiFi: 1 Ingrese a la configuración del sistema (consulte la página 48). 2 Cambie la configuración de 39 a 0 (consulte la página 54). La pantalla mostrará Wi-Fi Setup (configuración de WiFi). M33855 Para volver a conectarse a una red WiFi, siga los pasos en la página 26.
Actualizaciones del software Honeywell realiza actualizaciones periódicas del software para este termostato. Las actualizaciones se efectúan automáticamente a través de su conexión WiFi. Todas sus configuraciones permanecen guardadas, de modo que no necesita hacer cambios después de que ocurra la actualización. Mientras ocurre la actualización, la pantalla del termostato destella con el mensaje Updating (actualizando) y muestra el porcentaje de la actualización que ha ocurrido.
Tecnología Smart Response Esta característica permite que el termostato “sepa” cuánto demora el sistema de calefacción/refrigeración en alcanzar las configuraciones de temperatura programadas, de manera que se alcance esa temperatura a la hora que usted configuró. Por ejemplo: Configure la hora de despertarse a las 6:00 a.m. y la temperatura en 70 °F. La calefacción se encenderá antes de las 6:00 a.m., para que la temperatura esté en 70 °F a las 6:00 a.m.
Protección del compresor Esta característica hace que el compresor demore unos minutos antes de volver a iniciarse, para evitar daños al equipo. M33882 El mensaje Cool On (refrigeración encendida) (o Heat On [calefacción encendida] para una bomba de calor) destellará durante el período de espera.
Conversión automática Esta función se usa en climas en donde el acondicionador de aire y la calefacción se utilizan durante el mismo día. Cuando el sistema está configurado en Auto (Automático), el termostato elige automáticamente cuándo calentar o refrigerar, según la temperatura interior. MCR33893 El termostato ajustará automáticamente las configuraciones para mantener esta diferencia de 3 grados. Nota: la función de configuración del sistema 12 controla la conversión automática.
Opciones y funciones de configuración Puede cambiar las opciones en diversas funciones del sistema. Las funciones disponibles dependen del tipo de sistema que usted tenga. Las funciones junto con las opciones disponibles se describen en las páginas 50–54. Este termostato está preconfigurado para un sistema de calefacción/refrigeración de una sola etapa. La función de configuración 1 para la bomba de calor ajustará las configuraciones predeterminadas.
Opciones y funciones de configuración 1 Presione Fan (ventilador) y s simultáneamente y manténgalos presionados durante 3 segundos aproximadamente. La pantalla HOLD cambiará para mostrar dos números y las designaciones de los botones serán Done (terminado), Back (atrás), blank (en blanco), Next (siguiente). MCR33883 2 Presione Next (siguiente) hasta que vea el número de función—el número más grande a la izquierda—que desea configurar.
Configuración del sistema (Consulte la página 48 para obtener instrucciones.) Función 1 Seleccionar el tipo de sistema Si no está seguro sobre el tipo de sistema de calefacción/ refrigeración que tiene o si tiene alguna otra pregunta, visite wifithermostat.com Configuraciones y opciones 0 Calor/frío: Calefacción a gas, aceite o eléctrica con aire acondicionado central. 1 Bomba de calor: Bomba de calor sin calor de reserva ni calor auxiliar.
Configuración del sistema (Consulte la página 48 para obtener instrucciones.) Función Configuraciones y opciones 2 Válvula de cambio para bombas de calor (bombas de calor únicamente) 0 Válvula de cambio de refrigeración: Utilice esta configuración si conectó un cable con la etiqueta “O” al terminal O/B. 1 Válvula de cambio de calefacción: Utilice esta configuración si conectó un cable con la etiqueta “B” al terminal O/B.
Configuración del sistema (Consulte la página 48 para obtener instrucciones.) Función Configuraciones y opciones 12 Cambio manual/ automático Consulte la página 47 para obtener más información. 0 1 Cambio manual (Heat/Cool/Off [Calor/Frío/Apagado]). Cambio automático (Heat/Cool/Off [Calor/Frío/Apagado]). Activa, automáticamente, la calefacción o la refrigeración conforme a la temperatura ambiente.
Configuración del sistema (Consulte la página 48 para obtener instrucciones.) Función 36 Configuraciones y opciones Nombre del 52 = Thermostat dispositivo 1 Basement 2 Bathroom Este nombre 3 Bathroom 1 identificará el 4 Bathroom 2 termostato cuando 5 Bathroom 3 usted lo observe de 6 Bedroom manera remota. 7 Bedroom 1 Si registra múltiples 8 Bedroom 2 termostatos, debe 9 Bedroom 3 darle a cada uno un 10 Bedroom 4 nombre diferente.
Configuración del sistema (Consulte la página 48 para obtener instrucciones.) Función Configuraciones y opciones 38 WiFi encendida/ apagada 1 0 La red WiFi está encendida y puede conectarse a una red WiFi. La red WiFi está apagada. No se puede conectar el termostato a una red WiFi. Si no va a conectar el termostato a una red WiFi, el texto Wi-Fi Setup (Configuración de la red WiFi) desaparecerá del Centro de mensajes. 39 Conexión a la red WiFi 1 Está conectado a una red WiFi.
Preguntas frecuentes PP: ¿Mi termostato seguirá funcionando si pierdo la conexión a la red WiFi? RR: Sí, el termostato pondrá en funcionamiento el sistema de calefacción o refrigeración con o sin la conexión a la red WiFi. PP: ¿Cómo encuentro la contraseña de mi enrutador? RR: Comuníquese con el fabricante del enrutador o revise la documentación del enrutador. PP: ¿Por qué no puedo ver la página de configuración de la red WiFi? RR: Probablemente, esté conectado solo a su enrutador, y no al termostato.
Preguntas frecuentes PP: ¿Dónde puede encontrar mis códigos MAC ID y MAC CRC? RR: Los números MAC ID y MAC CRC se incluyen en una tarjeta empacada con el termostato o en la parte posterior del termostato (visible cuando se retira de la placa de pared). Cada termostato tiene un MAC ID y un MAC CRC únicos. PP: No puedo registrar mi termostato en el sitio web Total Connect Comfort. RR: Verifique que el termostato esté inscrito correctamente en su red doméstica WiFi.
Preguntas frecuentes PP: Me registré en el sitio web Total Connect Comfort, pero no pude iniciar sesión con mi nueva cuenta. RR: Revise su correo electrónico y asegúrese de haber recibido un mensaje de activación. Siga las instrucciones para activar su cuenta y, luego, inicie sesión en el sitio web. PP: Me he registrado en el sitio web Total Connect Comfort y no he recibido un correo electrónico de confirmación. RR: Revise que el correo electrónico no esté en la carpeta Correo no deseado o Eliminados.
Localización y solución de problemas Señal perdida Si se muestra el indicador no-Wi-Fi en vez del indicador de potencia WiFi en la esquina superior derecha de la pantalla de inicio: • Revise otro dispositivo para verificar que la conexión WiFi está funcionando en su hogar; si no, llame a su proveedor de Internet. • Mueva el enrutador. • Reinicie el termostato: para ello, retírelo de la placa de pared, espere 10 segundos y vuelva a calzarlo en la placa de pared presionándolo.
Localización y solución de problemas Códigos de error Para ciertos problemas, la pantalla del termostato mostrará un código que identifica el problema. Inicialmente se muestran códigos de error solos en el área de hora de la pantalla; luego de algunos minutos se muestra la pantalla de inicio y el código se alterna con la hora. Código de error M33999 Acción E01 Durante la configuración de WiFi, el enrutador perdió potencia. • Verifique que el enrutador recibe energía.
Localización y solución de problemas Código de error E42 Acción • Espere 30 minutos, puede tomar algunos El enrutador no está emitiendo una dirección minutos que se realice la conexión. • Si aún no hay conexión, retire el IP al termostato. termostato de la placa de pared durante 10 segundos y luego conéctelo nuevamente (consulte la página 26). • Verifique que su enrutador esté correctamente configurado para que le brinde una dirección IP automáticamente.
Localización y solución de problemas Si tiene dificultades con el termostato, intente seguir las sugerencias que se indican a continuación. La mayoría de los problemas pueden solucionarse de manera fácil y rápida. La pantalla está en blanco • Revise el interruptor de circuito y, si es necesario, reinícielo. • Asegúrese de que el interruptor de energía del sistema de calefacción y refrigeración esté encendido. • Asegúrese de que la puerta del sistema de calefacción esté bien cerrada.
Localización y solución de problemas Los problemas con la bomba de calor hacen que se enfríe el aire en la modalidad de calefacción, o que se caliente el aire en la modalidad de refrigeración • Verifique Función 2: válvula de cambio de la bomba de calor, para cerciorarse de que esté bien configurada según su sistema (consulte la página 51). El sistema de calefacción o refrigeración no responde • Presione System (Sistema) para configurar el sistema en Heat (Calefacción).
Localización y solución de problemas El sistema de calefacción está funcionando en modalidad de refrigeración • Verifique Función 1: tipo de sistema, para cerciorarse de que esté configurado de modo que se pueda utilizar con su equipo de calefacción y refrigeración (consulte la página 50). El equipo de refrigeración y el de calefacción están funcionando al mismo tiempo.
Glosario Cable C El cable “C”, o común, le transmite 24 V CA al termostato desde el sistema de calefacción/refrigeración. Es posible que algunos termostatos mecánicos o con batería más antiguos no tengan esta conexión de cables. Es necesario para establecer una conexión de la red WiFi a su red doméstica. Sistema de refrigeración/calefacción de bomba de calor Las bombas de calor se utilizan para calentar y refrigerar una casa.
Información sobre normativas Declaración de conformidad con las regulaciones FCC (Sección 15.19) (solo en los EE. UU.) Este dispositivo cumple con la Sección 15 de las regulaciones FCC. El funcionamiento está sujeto a las dos condiciones siguientes: 1 Este dispositivo no debe causar interferencia perjudicial, y 2 Este dispositivo deberá aceptar cualquier interferencia que se reciba, incluso la interferencia que pudiese causar el funcionamiento no deseado. Advertencia de la FCC (Sección 15.
Información sobre normativas Termostatos Para cumplir con los límites de exposición RF que establece la FCC y el Industry Canada para la población en general/exposición no controlada, la o las antenas usadas para estos transmisores deben instalarse a una distancia de, al menos, 20 cm de todas las personas, y no deben ubicarse ni utilizarse junto con otra antena o transmisor.
Garantía limitada de 1 año Honeywell garantiza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricación o de los materiales, a partir de la fecha de compra por parte del consumidor. Si en cualquier momento durante el período de garantía se verifica que el producto tiene un defecto o que funciona mal, Honeywell lo reparará o reemplazará (a elección de Honeywell).
69-2718ES-05 Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 wifithermostat.com ® Marca Registrada en los E.U.A. Apple, iPhone, iPad, iPod touch y iTunes son marcas comerciales de Apple Inc. Todas las demás marcas comerciales son propiedad de sus respectivos dueños. © 2015 Honeywell International Inc. 69-2718ES—05 M.S. Rev. 01-15 Impreso en EE. UU.