Quick Installation Guide RTH7400/RTH7500 Series Programmable Thermostat 69-2487ES-01
Advanced Installation Guide Installation is Easy Label wires and remove your old thermostat Install and wire your new thermostat Set your new thermostat to match your heating/cooling system – This thermostat works with virtually all System Types – It is preset for the most common system We are here to help. Call 1-800-468-1502 for wiring assistance before returning the thermostat to the store.
RTH7400/RTH7500 Series 1 Turn Off Power to Heating/ Cooling System M28097 1 69-2487ES—01
Advanced Installation Guide 2 Remove Old Thermostat Remove old thermostat but leave wallplate with wires attached. MERCURY NOTICE Is there a sealed tube containing mercury? If so, see back cover for proper disposal instructions.
RTH7400/RTH7500 Series 3 Label Wires with Tags Label the wires using the supplied wire labels as you disconnect them. M28100 Wire Labels M28093 NOTE: Jumper wire used on old thermostat? If yes, note what letters the jumper connected and review in wiring section.
Advanced Installation Guide 4 Separate Wallplate from New Thermostat Remove wallplate from the new thermostat and mount onto wall.
RTH7400/RTH7500 Series 5 Mount Wallplate Mount the new wallplate using the included screws and anchors. M28094 Drill 3/32-in. holes for plaster Drill 3/16-in. holes for drywall Use hammer to tap the anchors into the wall.
Advanced Installation Guide 6 Connect Wires Simply match wire labels. SCREW INSERT WIRES THEN TIGHTEN SCREWS LABELED WIRES CONVENTIONAL CONVENTIONAL WIRE HOLE C W G Y2 Y Y W2 W G R RC R M28070 Remove metal jumper if you have both R and Rc wires. Labels don’t match? See page 21. Have a Heat Pump system? See pages 22–23. We are here to help. Call 1-800-468-1502 for wiring assistance.
RTH7400/RTH7500 Series 7 Install Batteries Install two AA alkaline batteries and remove tab. M28101 Back of thermostat Remove tab.
Advanced Installation Guide 8 Install Thermostat onto Wallplate Install thermostat onto the wallplate on the wall.
RTH7400/RTH7500 Series 9 Turn Power Back On Turn the power back on to the heating/cooling system.
Advanced Installation Guide 10 Set Time and Date Press s or t to set month, then press NEXT. Press s or t to set day, then press NEXT. Press s or t to set year, then press DONE. Month Year 6 Go Back Day 2006 Next 15 Done M28095 Press s or t to set time, then press DONE to save and exit.
RTH7400/RTH7500 Series 11 If your system type is... If your system type is: q Single Stage Heat and Cool Congratulations, you’re done! If your system type is: q Multistage Heat and Cool q Heat Pump* without Backup Heat q Heat Pump* with Backup Heat q Heat Only q Cool Only Continue with advanced installation on next page to match your thermostat to your sytem type. *Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.
Advanced Installation System setup.......................................................................13 Wiring...................................................................................21 Troubleshooting...................................................................24 Customer assistance..........................................................26 Limited warranty..................................................................
RTH7400/RTH7500 Series About your System setup new thermostat Step 1 Press and release the left button. SETUP 0120 System & Fan Schedule 20 Clock & More WIRING M27459 Press and hold the center button until the screen changes (approximately 5 seconds).
Advanced Installation Guide SETUP About your setting Navigating new thermostat changes Use this navigation to set and change settings on pages 15-20. Press s t to change setting. ASSISTANCE WIRING Function Go Back Setting 0120 20 Next Done Press NEXT to advance to next function. Press DONE to save & exit. TROUBLESHOOTING NOTE: Some functions in the following pages may not appear due to previous selections made.
RTH7400/RTH7500 Series About your System setup new thermostat See page 14 to navigate between functions. Function Settings & Options 0120 Year Setting (first two digits) Press s/t to change the first two digits of the year: WIRING 20 = Year 20xx 21 = Year 21xx Press NEXT 0130 Year Setting (second two digits) Press s/t to change the last two digits of the year: 01 - 99 (i.e., 2001 - 2099) Press s/t to change the current month: 01 - 12 (i.e.
Advanced Installation Guide About your System setup new thermostat Function Settings & Options 0170 Select System Type Press s/t to select your system type: 1 Heat/cool: Gas, oil or electric heating with central air conditioning. 2 Heat pump: Heat pump without backup or auxiliary heat. 3 Heat only: Gas, oil or electric heat without central air conditioning. 4 Heat only with fan: Gas, oil or electric heat without central air conditioning.
RTH7400/RTH7500 Series About your System setup new thermostat See page 14 to navigate between functions. Press s/t to select your heating system & fan control: 0 Gas or oil heat: Use this setting if you have a gas or oil heating system (system controls fan operation). 1 Electric heat: Use this setting if you have an electric heating system (thermostat controls fan operation).
Advanced Installation Guide About your System setup new thermostat Function Settings & Options 0240 Heating Cycle Rate Press s/t to select your heating system: 5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency). 9 Electric furnace: Electric heating systems. 3 Hot water or high-efficiency furnace: Hot water system or gas furnace (more than 90% efficiency). 1 Gas/oil steam or gravity system: Steam or gravity heat systems.
RTH7400/RTH7500 Series About your System setup new thermostat See page 14 to navigate between functions. Press s/t to select manual or automatic changeover: 0 Manual changeover (Heat/Cool/ Off). 1 Automatic changeover (Heat/ Cool/Auto/Off). Automatically turns on Heat or Cool based on room temperature. Note: System maintains minimum 3°F difference between heat and cool settings.
Advanced Installation Guide About your System setup new thermostat Function Settings & Options 0500 Furnace Filter Change Reminder Press s/t to set the desired reminder interval: 0 Off (no reminder) 1 Reminder in about 1 month 2 Reminder in about 3 months 3 Reminder in about 6 months 4 Reminder in about 9 months 5 Reminder in about 1 year 6 Reminder in about 3 years WIRING SETUP See page 14 to navigate between functions.
RTH7400/RTH7500 Series About your new thermostat Wiring—conventional system Alternate wiring (conventional systems) C G G Y Y W W RC W2 Y2 R 2 2 W2 Y2 MCR32160 If your old thermostat had both R and RH wires, remove metal jumper. Connect the R wire to the Rc terminal, and the RH wire to the R terminal. If your old thermostat had only 1 C or C1 wire, connect it to the C terminal. If your old thermostat had 2 C or C1 wires, wrap each separately with electrical tape and do not connect them.
Advanced Installation Guide About your new Wiring—heat pump thermostat WIRING SETUP Connect wires: Heat Pump 1. Match each labeled wire with same letter on new thermostat. 2. Use a screwdriver to loosen screws, insert wires into hole under screw, then tighten screws until wire is secure. 3. If E and Aux do not each have a wire connected, use a small piece of wire to connect them to each other. 4. Push any excess wire back into the wall opening.
RTH7400/RTH7500 Series Wiring—heat pump Alternate wiring (for heat pumps only) 5 C SETUP 3 G Y 3 O/B RC R 6 AUX 6 E 5 L WIRING 4 2 MCR32161 Wiring complete, return to Step 7. 23 69-2487ES—01 TROUBLESHOOTING 6 ASSISTANCE 5 Leave metal jumper in place, connecting R & Rc terminals. If your old thermostat had both V and VR wires, stop now and contact a qualified contractor for help. If your old thermostat had separate O and B wires, attach the B wire to the C terminal.
Advanced Installation Guide Display is blank Make sure fresh AA alkaline batteries are properly installed (see page 7). Cannot change system setting to Cool Check Function 0170: System Type to make sure it is set to match your heating and cooling equipment (see page 16). Fan does not turn on when heat is required Check Function 0180: Heating Fan Control to make sure it is set to match your heating equipment (see page 17).
RTH7400/RTH7500 Series Troubleshooting Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor. Heat pump issues cool air in heat mode, or warm air in cool mode Check Function 0190: Heat Pump Changeover Valve to make sure it is properly configured for your system (see page 17). ASSISTANCE “Wait” appears on the screen WIRING Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature.
Advanced Installation Guide For assistance with this product, please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502.
RTH7400/RTH7500 Series 1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal. CAUTION: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C).
Guía de instalación rápida Serie RTH7400/RTH7500 Termostato programable 69-2487ES-01
Guía de instalación rápida ¡La instalación es fácil! Rotule los cabes y retire el termostato viejo Instale y conecte los cables de su nuevo termostato Ajuste su nuevo termostato para que concuerde con su sistema de calefacción/refrigeración – Este termostato funciona prácticamente con todos los tipos de sistemas – Está preconfigurado para el sistema más común Estamos aquí para ayudarle. Llame al 1-800-468-1502 para obtener asistencia con el cableado antes de devolver el termostato a la tienda.
Serie RTH7400/RTH7500 1 Desconecte la alimentación en el sistema de calefacción/ refrigeración M28097 1 69-2487ES—01
Guía de instalación rápida 2 Remueva su viejo termostato Retire el termostato existente pero deje la placa de montaje con los cables adheridos. Deje la placa de montaje en su lugar AVISO SOBRE EL MERCURIO ¿Hay un tubo sellado que contiene mercurio? Si es así, consulte en la cubierta de este manual las instrucciones para su desecho apropiado.
Serie RTH7400/RTH7500 3 Identifique los cables con etiquetas Identifique los cables a medida que los desconecta, utilizando las etiquetas que se suministran. M28100 Rótulos para los cables M28093 NOTA: Jumper wire used on old thermostat? If yes, note what letters the jumper connected and review in wiring section.
Guía de instalación rápida 4 Separe la placa de montaje del termostato nuevo Retire la placa de montaje del termostato nuevo y móntela en la pared.
Serie RTH7400/RTH7500 5 Coloque la placa de montaje Monte la nueva placa de montaje utilizando los tornillos y anclajes que se suministran. M28094 Taladre agujeros de 3/32 in. (2,4 mm) en yeso Taladre agujeros de 3/16 in. (4,8 mm) en paneles de yeso Use hammer to tap the anchors into the wall.
Guía de instalación rápida 6 Conecte los cables Simplemente haga corresponder las etiquetas de los cables. TORNILLO INSERTE LOS CABLES Y APRIETE LOS TORNILLOS CABLES ETIQUETADOS ORIFICIO DE CONVENCIONAL CABLEADO CONVENCIONAL C W G Y2 Y Y W2 W G R RC R MS28070 Retire el empalme metálico si tiene los cables “R” y “Rc”. ¿Los rótulos no coinciden? Vea la página 21. ¿Tiene un sistema de bomba de calor? Ver páginas 22-23. Estamos aquí para ayudarle.
Serie RTH7400/RTH7500 7 Instale las baterías Instale dos baterías alcalinas AA en la parte de atrás del termostato. M28101 Parte de atrás del termostato Retire la lengüeta.
Guía de instalación rápida 8 Instale el termostato en la placa de montaje Instale el termostato en la placa de montaje en la pared.
Serie RTH7400/RTH7500 9 Active nuevamente el suministro eléctrico Active nuevamente el suministro eléctrico del sistema de calefacción/aire acondicionado.
Guía de instalación rápida 10 Ajuste de fecha y hora Oprima s o t para ajustar el mes, después oprima NEXT. Oprima s o t para ajustar la fecha, después oprima NEXT. Oprima s o t para ajustar el año, después oprima DONE. El mes El año 6 Go Back 2006 Next La fecha 15 Done M28095 Oprima s o t para ajustar la hora, después oprima DONE para salir y guardar los ajustes.
Serie RTH7400/RTH7500 11 Si su tipo de sistema es... Si su tipo de sistema es: q Calor y frío de una sola etapa ¡Felicitaciones, ya está listo! Si su tipo de sistema es: q Calor y frío de etapas múltiples q Bomba de calor* sin calor de respaldo q Bomba de calor* con calor de respaldo q Solo calor q Solo frío Continúe con la instalación avanzada en la próxima página para adaptar el termostato a su tipo de sistema.
Guía de instalación avanzada Cómo cambiar la configuración.........................................13 Cableado..............................................................................21 En caso de dificultades......................................................24 Asistencia al cliente............................................................26 Garantía limitada.................................................................
Serie RTH7400/RTH7500 About cambiar Cómo your newlathermostat configuración CONFIGURACIÓN Paso 1 Presione y sostenga el botón izquierdo. 0120 System & Fan Schedule 20 Clock & More WIRING M27459 Presione y sostenga el botón central hasta que cambie la pantalla (aproximadamente 5 segundos).
Guía de instalación avanzada CONFIGURACIÓN About your setting Navigating new thermostat changes Use this navigation to set and change settings on pages 15-20. Oprima s o t para cambiar los ajustes. WIRING Function TROUBLESHOOTING ASSISTANCE Go Back Setting 0120 20 Next Done Oprima NEXT para seleccionar la función. Oprima DONE para salir y guardar los ajustes. NOTA: Algunas funciones de las páginas siguientes puede que no aparezcan debido a las selecciones efectuadas previamente.
Serie RTH7400/RTH7500 About cambiar Cómo your newlathermostat configuración Refiérase a la página 14 para navegar entre funciones. Configuraciones y opciones Oprima s/t para cambiar los primeros dos dígitos del año: 20 = Año 20xx 21 = Año 21xx Presione NEXT (siguiente) 0130 Ajuste de año (segundos dos dígitos) Oprima s/t para cambiar los últimos dos dígitos del año: 01 - 99 (ej., 2001 - 2099) Oprima s/t para cambiar el mes actual: 01 - 12 (i.e.
Guía de instalación avanzada Refiérase a la página 14 para navegar entre funciones.
Serie RTH7400/RTH7500 About cambiar Cómo your newlathermostat configuración Configuraciones y opciones Oprima s/t para seleccionar su sistema de calefacción: 0 Calefacción a gas/petróleo: (Operación del ventilador de los controles de sistema). 1 Calefacción eléctrica: (El termóstato controla la operación del ventilador).
Guía de instalación avanzada CONFIGURACIÓN Cómo cambiar la configuración Refiérase a la página 14 para navegar entre funciones.
Serie RTH7400/RTH7500 Cómo cambiar la configuración Configuraciones y opciones Oprima s/t para seleccionar el cambio manual o automático. 0 El cambio manual (Heat/Cool/ Off). 1 El cambio automático (Heat/ Cool/Auto/Off). Nota: El sistema mantiene la diferencia mínima 3°F entre el calor y los ajustes frescos.
Guía de instalación avanzada CONFIGURACIÓN About cambiar Cómo your newlathermostat configuración Refiérase a la página 14 para navegar entre funciones.
Serie RTH7400/RTH7500 About your new thermostat Cableado—sistemas convencionales Cableado alterno (sistemas convencionales) C G G Y Y W W RC Rc W2 Y2 R 2 2 W2 Y2 MCRS32160 ASSISTANCE R 3 CABLEADO C SETUP Si las etiquetas no corresponden con los terminales, conecte los cables como se ilustra aquí (ver notas más abajo). Quite el empalme metálico que conecta R y RC solamente si usted debe conectar los alambres de R y de Rc.
Guía de instalación avanzada About Cableado—bomba your new thermostat de calefacción CABLEADO SETUP Conecte los cables: Bomba de calor 1. Coordine cada cable etiquetado con la misma letra del termostato nuevo. 2. Con un destornillador afloje los tornillos de los terminales, inserte los cables, luego ajuste los tornillos. 3. Si E y Aux no tienen un cable conectado cada uno, utilice una pequeña pieza de cable para conectarlos uno con otro. 4. Introduzca el excedente de cable en la abertura de la pared.
Serie RTH7400/RTH7500 About Cableado—bomba your new thermostat de calefacción Câblage alternatif (pour thermopompes seulement) 5 C SETUP 3 G Y O/B 3 RC 6 CABLEADO 2 4 R AUX 6 E 5 L MCRS32161 El cableado está completo, regrese al paso 7. 23 69-2487ES—01 TROUBLESHOOTING 6 ASSISTANCE 5 Deje el empalme en lugar, entre terminales de R y Rc. Si su viejo termóstato tenía alambres V y VR, ahora pare y entre en contacto con un contratista para la ayuda.
Guía de instalación avanzada EN CASO DE DIFICULTADES ASSISTANCE WIRING SETUP En caso de dificultades Si usted tiene dificultades con su termostato, pruebe las sugerencias que figuran a continuación. La mayoría de los problemas se pueden solucionar rápida y fácilmente. Pantalla en blanco Asegúrese de que estén bien instaladas las nuevas baterías alcalinas AA (ver página 7).
Serie RTH7400/RTH7500 En caso de dificultades El bombeo de calor emite aire frío en modo calefacción o aire caliente en modo refrigeración Verifique la Función 190: Válvula de cambio del sistema de bombeo de calor para asegurarse de que esté configurada correctamente para su sistema (ver página 17). 25 69-2487ES—01 EN CASO DE DIFICULTADES La función de protección del compresor está activada. Espere 5 minutos el reinicio seguro del sistema, sin dañar el compresor.
Guía de instalación avanzada Si necesita asistencia, visite http://yourhome.honeywell.com o llame al número gratuito de atención al cliente de Honeywell al 1 800 468-1502. TROUBLESHOOTING ASISTENCIA WIRING SETUP Asistencia al cliente Garantía limitada de 1 año Honeywell garantiza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricación o de los materiales, a partir de la fecha de compra por parte del consumidor.
RTH7400/RTH7500 Series Garantía limitada de 1 año La única responsabilidad de Honeywell será reparar o reemplazar el producto dentro de los plazos establecidos anteriormente. HONEYWELL NO RESPONDERÁ POR LA PÉRDIDA O DAÑO DE NINGÚN TIPO, INCLUIDO EL DAÑO INCIDENTAL O INDIRECTO DERIVADO, DIRECTA O INDIRECTAMENTE, DEL INCUMPLIMIENTO DE LAS GARANTÍAS, EXPRESAS O IMPLICÍTAS, O DE OTRAS FALLAS DE ESTE PRODUCTO.
Este termostato tiene una batería de litio que puede contener perclorato. Perclorato: puede ser necesario manipularlo con métodos especiales. Visite www.dtsc.ca.gov/hazardouswaste/perchlorate AVISO DE MERCURIO: No arroje su viejo termostato a la basura si contiene mercurio en un tubo sellado. Comuníquese con la autoridad local de disposición de desechos para recibir instrucciones sobre reciclado y eliminación correcta.