User Guide Wi-Fi Touchscreen Programmable Thermostat RTH8500 Wi-Fi Series
In the box you will find • Thermostat • Wallplate (attached to thermostat) • Screws and anchors • Coin cell battery (inside the back of the thermostat) • Quick Start Guide • Thermostat ID Card • Wire labels • User Guide 69-2715ES—07 ii
Welcome Congratulations on your purchase of a Honeywell Wi-Fi touchscreen programmable thermostat. When registered to Honeywell’s Total Connect Comfort Solutions, you can remotely monitor and control the heating and cooling system in your home or business— you can stay connected to your comfort system wherever you go.
This thermostat works with common 24 volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat. This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply. See www.dtsc.ca.
Table of contents About your new thermostat Setting filter reminder intervals.................. 43 Cleaning the screen................................... 44 Unregistering thermostat........................... 45 Disconnecting Wi-Fi................................... 46 Special features......................................... 48 Setting functions and options..................... 51 Home screen quick reference...................... 5 Preset energy-saving schedules..................
Features of your Wi-Fi thermostat With your new thermostat, you can: • Connect to the Internet to monitor and control your heating/cooling system • View and change your heating/cooling system settings • View and set temperature and schedules • Receive alerts via email and get automatic upgrades Your new thermostat provides: • Smart Response Technology • Compressor protection • Heat/cool auto changeover 69-2715ES—07 4
Home screen quick reference Once your Wi-Fi thermostat is installed, it will display the home screen. Portions of this display will change depending on how you are viewing it. To change settings, simply press the appropriate area lightly with your finger.
Preset energy-saving schedules This thermostat is pre-set with energy-saving program settings for four time periods. Using the default settings can reduce your heating/cooling expenses if used as directed. Savings may vary depending on geographic region and usage. WAKE 6:00 am LEAVE 8:00 am RETURN 6:00 pm SLEEP 10:00 pm Default Heat Settings Default Cool Settings 70 ° 78 ° 62 ° 85 ° 70 ° 78 ° 62 ° 82 ° To change the settings, see pages 39–42.
Setting up your thermostat Setting up your Wi-Fi programmable touchscreen thermostat is easy. It is preprogrammed and ready to go as soon as it is installed and registered. 1 Install your thermostat. 2 Connect it to your home wireless network. 3 Register online for remote access. Before you begin, you may want to watch a brief installation video. Use the QR Code at the front of this guide, or go to wifithermostat.
Installing your thermostat You might need the following tools to install this thermostat: • • • • No. 2 Phillips screwdriver Small pocket screwdriver Pencil Level (optional) • Drill and bits (3/16” for drywall, 7/32” for plaster) (optional) • Hammer (optional) • Electrical tape (optional) 1 Switch OFF power to your heating/cooling system. or Important! To protect your equipment, switch OFF the power to your heating/ cooling system at the breaker box or the system switch.
Installing your thermostat 2 Remove old thermostat faceplate and leave wires connected. If you have an older thermostat with a sealed mercury tube, turn to page 2 for proper disposal instructions. 2a Take a picture of the wire connections for later reference. 2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at wifithermostat.com/videos C C Important! C wire is required and is the primary power source for your thermostat.
Installing your thermostat 3 Label wires. Do not label by wire color. Use the supplied sticky tags to label each wire as you disconnect it. Label wires according to the old thermostat terminal designations, not by wire color. Sticky tag Blank tags Note: If no tag matches a terminal designation, write the appropriate letter on a blank sticky tag. 4 Remove wallplate. Remove the old wallplate from the wall after all wires have been labeled and disconnected.
Installing your thermostat 5 Separate Wi-Fi thermostat and its wallplate. Finger holds Thermostat On your new thermostat, grasp the finger holds on the top and bottom of the wallplate with one hand and the thermostat (front) with the other hand. Pull pieces apart.
Installing your thermostat 6 Mount wallplate for Wi-Fi thermostat. Mount your new wallplate using screws and anchors included with the thermostat. Wallplate If necessary: Drill 3/16-in holes for drywall. HEAT PUMP CONVENTIONAL Drill 7/32-in holes for plaster. Note: You may be able to use your existing wall anchors. Hold the wallplate up to the existing anchors to check for alignment.
Installing your thermostat Important! The Wi-Fi thermostat requires a C wire to operate. The C, or common, wire brings 24 VAC power to the thermostat. Many older mechanical or battery operated thermostats do not require a C wire. If you don’t have a C wire, try: • Looking for an unused wire that is pushed into the wall. Connect that wire to C and check that it is connected to the 24 VAC common at your heating/cooling system. Check the video section at wifithermostat.
Installing your thermostat Wiring (conventional system) Remove metal jumper only if you have both R and RC wires C G Y W R 7A Wire the Wi-Fi thermostat to your conventional system. a Starting with the C Wire, match the sticky tag on the wire to the terminal labels. HEAT PUMP CONVENTIONAL You must have a C wire. See page 13. b Loosen screw, insert wire on inside edge of RC RC Y2 R R L terminal, then tighten screw. O/B W W2 E/AUX c Verify wire is firmly secured by gently pulling Y Y K K on wire.
Installing your thermostat Wiring (heat pump system only) Labels don’t match? See alternate wiring key on pages 18–19. O Note: If old thermostat has separate wires on AUX and E, place both wires into the E/AUX terminal. If old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No jumper is required. 15 MCR33529 C G Y AUX R 7B Wire Wi-Fi thermostat to your heat pump. a Starting with the C Wire, match the sticky tag on the wire to the terminal labels.
Installing your thermostat Alternate wiring (conventional system) Use this if your wire labels don’t match the terminal labels. CONVENTIONAL Note: You must have a C wire or equivalent. See page 13. Metal Jumper Y2 W2 3 Y2 W2 K RC RC 1 R R 2 W W Y Y G G C C See key to 1 – 3 on page 17.
Installing your thermostat Alternate wiring key (conventional system) 1 Remove metal jumper connecting R and RC only if you must connect both R and RC. 2 If your old thermostat had both R and RH wires, remove metal jumper. Connect the R wire to the RC terminal, and the RH wire to the R terminal. 3 Do not use K terminal. For future use.
Installing your thermostat Alternate wiring (heat pump system only) Use this if your wire labels don’t match the terminal labels. HEAT PUMP Metal Jumper Note: You must have a C wire or equivalent. See page 13. Y2 5 6 7 RC 1 R L E/AUX RC O AUX K R 2 O/B 3 Y Y G 4 G C C 3 MCR33530A 69-2715ES—07 18 See key to 1 – 7 on page 19.
Installing your thermostat Alternate wiring key (heat pump system only) 1 Leave metal jumper between R and RC terminals in place. 2 If your old thermostat had both V and VR wires, check wifithermostat.com for help. 3 If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If another wire is attached to the C terminal, check wifithermostat.com for help. Attach the O wire to the O/B terminal. Set System Function 0190 to 0 (see page 55).
Installing your thermostat 8 Install battery. Insert the coin cell battery (included), observing the correct polarity. Note: A correctly inserted battery will extend about halfway out of the battery slot on the thermostat, allowing for easier removal. This battery maintains time and date during power outages. It does not power the thermostat (C wire required).
Installing your thermostat Wallplate 9 Attach thermostat to wallplate. Align the thermostat to the wallplate and then snap into place.
Installing your thermostat 10 Switch heating/cooling system ON. Important! 10a Verify that the C wire is connected at the thermostat and at the heating/cooling system. or 10b Make sure the heating/ cooling system door is firmly secured. 10c Switch power back ON for your heating/cooling system at the breaker box or its power switch.
Installing your thermostat 11 Set date and time. Touch s or t buttons to change displayed time and date. Day Year Press and hold a button to quickly change a setting. Note: This thermostat will automatically update for daylight saving time (if observed in your area) and all date/time information is stored. If the thermostat is connected to Wi-Fi and registered to Total Connect Comfort, the current time is updated from the internet.
Installing your thermostat 12 Determine your heating/cooling system type. Important! Heating/cooling system type must be set so that your thermostat operates properly and does not damage your system. 12a If you have a traditional system (natural gas forced air with A/C), your hermostat is set up by default to control this system.
Installing your thermostat Congratulations! Your thermostat is operational. 13 Test your thermostat. 13b For remote access to your thermostat, continue to “Connecting to your Wi-Fi network” on page 26. Inside MORE MCR31580 13a Press the SYSTEM button to change to heating or cooling and begin operation. Heating/cooling system not turning on? Refer to page 67 or FAQ at wifithermostat.
Connecting to your Wi-Fi network To complete this process, you must have a wireless device connected to your home wireless network. Any of these device types will work: • Tablet (recommended) • Laptop (recommended) • Smartphone If you get stuck... at any point in this procedure, restart the thermostat by removing the thermostat from the wallplate, wait for 5 seconds, and snap it back onto the wallplate. Return to Step 1 in this procedure, which starts on page 27.
Connecting to your Wi-Fi network 1 Connect to your thermostat. 1a Make sure the thermostat message center displays Wi-Fi SETUP. 1b On the wireless device (laptop, tablet, smartphone), view the list of available Wi-Fi networks Inside MORE Note: If you are asked to specify a home, public, or office network, select Home Network. 27 M31566 1c Connect to the network called NewThermostat_123456 (the number will vary).
Connecting to your Wi-Fi network 2 Join your home network. 2a Open your web browser to access the Thermostat Wi-Fi Setup page. The browser should automatically direct you to the correct page; if it does not, go to http://192.168.1.1 2b Find the name of your home network on this page and select it. 2c Complete the instructions for joining your Wi-Fi network and click on the Connect button. (Depending on your network setup, you may see an instruction such as Enter Password for your home network.
Connecting to your Wi-Fi network Note: If your Wi-Fi network does not appear in the list on the Thermostat Wi-Fi Setup page: • Try performing a network rescan by pressing the Rescan button. This is helpful in areas with a lot of networks. • If you are connecting to a hidden network, then enter the network SSID in the textbox, select the encryption type from the drop down menu, and click on the Add button. This manually adds the network to the top of the list.
Connecting to your Wi-Fi network 3 Make sure your thermostat is connected. Look at the thermostat display. Verify that the message center displays one of the following: CONNECTION SUCCESSFUL JOINED: [WI-FI NETWORK NAME] YOU ARE ALMOST DONE REGISTER AT TOTAL CONNECT Inside MORE If you see one of these messages, continue on page 31. Note: If you see CONNECTION FAILURE or Wi-Fi SETUP in the message center, confirm you correctly entered your home network password in step 2c.
Registering your thermostat online To view and set your Wi-Fi thermostat remotely, you must have a Total Connect Comfort account. Use the following steps. 1 Open the Total Connect Comfort web site. Go to mytotalconnectcomfort.com M31570 View the Wi-Fi Thermostat Registration video at wifithermostat.
Registering your thermostat online 2 Login or create an account. If you have an account, click Login click Create An Account 2a Follow the instructions on the screen. 2b Check your email for an activation message from My Total Connect Comfort. This may take several minutes. Note: If you do not receive a response, check your junk mailbox or use an alternate e-mail address. 2c Follow activation instructions in the email. 2d Log in.
Registering your thermostat online 3 Register your Wi-Fi thermostat. After you are logged in to your Total Connect Comfort account, register your thermostat. 3a Follow the instructions on the screen. After adding your thermostat location, you must enter the thermostat’s unique identifiers: • MAC ID • MAC CRC Note: These IDs are listed on the Thermostat ID Card included in the thermostat package. The IDs are not case sensitive.
Registering your thermostat online 3b When the thermostat is successfully registered, the Total Connect Comfort registration screen will display a SUCCESS message.
Registering your thermostat online 3c Also notice that your thermostat will now display its signal strength. Congratulations! You’re done. You can now control your thermostat from anywhere through your tablet, laptop, or smartphone. Total Connect Comfort free app is available for Apple iPhone , iPad and iPod touch devices at iTunes or at Google Play for all Android™ devices.
Setting the clock 1 Press CLOCK to display setting arrows. 2 Press s or t to adjust the time. (You can advance the time more quickly by holding the s or t buttons.) MORE Note: This thermostat will automatically update for daylight saving time (if observed in your area) and all date/time information is stored. If the thermostat is connected to Wi-Fi and registered to Total Connect Comfort, the current time is updated from the internet.
Setting the fan 1 Press FAN to select fan operation. 3 Press DONE to save setting. Your selection appears under FAN. ON: Fan is always on. AUTO: Fan runs only when the heating or cooling system is on. 37 Inside MORE MCR31553 2 Press FAN again to select ON or AUTO (toggle to re-select). The selected option blinks.
Selecting system mode 1 Press SYSTEM to display options. 2 Press SYSTEM again to select an option. You may need to press two or three times to make a selection—the selected option blinks. Inside Possible system modes: HEAT: Controls only the heating system. COOL: Controls only the cooling system. OFF: Heating/cooling systems are off. AUTO: Selects heating or cooling depending on the indoor temperature. EM HEAT (heat pumps with aux. heat): Controls auxiliary/emergency heat. Compressor is locked out.
Adjusting program schedules 1 Press SCHED, then EDIT. Screen displays day buttons at top. 2 Press day buttons (MON–SUN) to select days. MORE SLEEP 3 Press s or t to set Wake time for selected day(s). 4 Press s or t to set Heat and Cool temperature for this time period. 5 Press another period (LEAVE, RETURN, SLEEP) and set time and temperatures for each. Note: You can press CANCEL PERIOD to eliminate any unwanted time period.
Overriding schedules temporarily 1 On the home screen, press s or t to immediately adjust the temperature. The new setting will be maintained until the time shown under Hold Until. When the timer expires, the schedule will resume, and the temperature will return to the setting for the current time period. To cancel the temporary setting at any time, press CANCEL (or SCHED). The program schedule will resume.
Overriding schedules permanently 1 Press HOLD to permanently adjust the temperature. This will turn off the program schedule. 2 Whatever temperature you set will be maintained 24 hours a day until you manually change it or press CANCEL (or SCHED) to cancel “Hold” and resume the program schedule.
Setting vacation hold Use this function to suspend the program schedule while you are away for an extended period. Inside 1 Press s or t to set the temperature. 2 Press s or t to set the time of day you want the schedule to resume on the day you return. Hold Until MORE 3 Press HOLD twice. Hold Until appears. 4 Press s or t to select the number of days. Note: You can press CANCEL (or SCHED) to resume normal schedule.
Setting filter reminder intervals If activated during installation, the filter reminder alerts you with a message above the time when it is time to replace your filter. Press RESET after changing the filter, to restart the timer. Inside RESET CHANGE FILTER To change the reminder interval: MORE 1 Press MORE, then EDIT. SLEEP 2 Press s or t to select the desired interval (in days), then press DONE. DAYS 3 Press RESET. Note: System setting function 0500 governs the filter interval.
Cleaning the screen 1 Press SCREEN to lock the screen for cleaning. The screen will remain locked for 30 seconds so you can clean the screen without changing any settings. MORE 2 After 30 seconds, press DONE to resume normal operation, or press SCREEN again if you require more time for cleaning. MCR31560 Note: Do not spray any liquid directly on the thermostat. Spray liquid onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers.
Unregistering thermostat If you remove the thermostat from your Total Connect Comfort website account (for example, you’re moving and leaving the thermostat behind), the message center will scroll UNREGISTERED FROM TOTAL CONNECT for 3 minutes. After that, it will alternate displaying REGISTER AT TOTAL CONNECT, the MAC ID and the MAC CRC.
Disconnecting Wi-Fi Replacing your router The Message Center will display Wi-Fi DISCONNECTED for 1 minute. After that it will display Wi-Fi SETUP. Inside MORE M31573 If you disconnect the thermostat from your Wi-Fi network: 1 Enter system setup (see page 51). 2 Change setting 900 to 0 (see page 58). Re-connect to a Wi-Fi network by following the steps on page 26.
Software updates While the update is taking place, your thermostat screen goes blank and the message center shows UPDATING and the percentage of the update that has occurred. When the update is complete, your home screen will appear as usual. M34184 Honeywell periodically issues updates to the software for this thermostat. The updates occur automatically through your Wi-Fi connection. All your settings are saved, so you will not need to make any changes after the update occurs.
Smart Response Technology This feature allows the thermostat to “learn” how long the heating/cooling system takes to reach programmed temperature settings, so the temperature is reached at the time you set. For example: Set the Wake time to 6:00 am, and the temperature to 70°. The heat will come on before 6:00 am, so the temperature is 70° by 6:00 am. Note: System setting function 0530 controls Smart Response Technology. See “Smart Response Technology” on page 57.
Compressor protection This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage. During the wait time, the message “Wait” is displayed on screen.
Auto changeover This feature is used in climates where both air conditioning and heating are used on the same day. When the system is set to AUTO, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation. Note: System setting function 0300 controls Auto changeover. See “Manual/Auto Changeover” on page 56.
Setting functions and options You can change options for a number of system functions. Available functions depend on the type of system you have. The functions, designated with four-digit numbers, along with available options are described on pages 52–58. This thermostat is pre-set for a single-stage heating/cooling system. Setting function 0170 for a heat pump will adjust the default settings. HEAT 5 When you have made all changes, press DONE to save and exit.
System setup How do I set my thermostat name? (See page 51 for instructions.) Function 0112 Settings & Options 52 = Thermostat Device Name 1 Basement This name will 2 Bathroom identify the thermostat when you 3 Bathroom 1 4 Bathroom 2 view it remotely. 5 Bathroom 3 If you register 6 Bedroom multiple thermostats, 7 Bedroom 1 give each one a 8 Bedroom 2 different name.
System setup How do I change time and date settings? (See page 51 for instructions.) Function Settings & Options 0120 Year Setting (first two digits) 20 = Year 20xx 21 = Year 21xx 0130 Year Setting (last two digits) 01–99 (i.e., 2001–2099) 0140 Month Setting 01–12 (i.e., January–December) 0150 Date Setting 01–31 0160 Schedule Options 4 0 Program schedule is on (7-day programmable). Program schedule is off. Thermostat can not be programmed.
System setup How do I set my heating/cooling system type? (See page 51 for instructions.) Function 0170 Select System Type If you are not sure of your heating/cooling system type or have other questions, go to wifithermostat.com 69-2715ES—07 Settings & Options 1 Heat/cool: Gas, oil or electric heating with central air conditioning. 2 Heat pump: Heat pump without backup or auxiliary heat. 4 Heat only with fan: Gas, oil or electric heat without central air conditioning.
System setup How do I customize my heating/cooling system? (See page 51 for instructions.) Function Settings & Options Note: Depending on system settings, functions on this page might not appear. Heating Fan Control 0 Heat Pump Changeover Valve (for heat pumps only) 0 0240 Heating Cycle Rate 0250 Heating Cycle Rate Stage 2 5 9 3 0180 0190 1 1 1 Gas or oil heat: Use this setting if you have a gas or oil heating system (system controls fan operation).
System setup What other functions can I change? (See page 51 for instructions.) Function Settings & Options 0280 Backlight 0 1 0300 Manual/Auto Changeover See page 50 for more information. 0 1 Manual changeover (Heat/Cool/Off). Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat or Cool based on room temperature. Note: System maintains minimum 3°F difference between heat and cool settings.
System setup What other functions can I change? (See page 51 for instructions.) Function Settings & Options 0500 Filter Change Reminder The reminder appears after selected number of days run time not actual time.
System setup How do I change my Wi-Fi settings? (See page 51 for instructions.) Function Settings & Options 0710 Restore Original Settings 0 1 0890 Wi-Fi On/Off 1 0 Wi-Fi is on and can be connected to a Wi-Fi network. Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you are not connecting the thermostat to a Wi-Fi network this will remove the text “Wi-Fi Setup” from the messaging center. 0900 Wi-Fi Connection 1 Connected to Wi-Fi network.
Frequently asked questions QQ: Will my thermostat still work if I lose my Wi-Fi connection? AA: Yes, the thermostat will operate your heating and/or cooling system with or without Wi-Fi. QQ: How do I find the password to my router? AA: Contact the manufacturer of the router or check the router documentation. QQ: Why am I not seeing my Wi-Fi setup page? AA: You are probably connected only to your router, not to your thermostat. Try connecting to the thermostat again.
Frequently asked questions QQ: Where can I find my MAC ID and MAC CRC codes? AA: The MAC ID and MAC CRC will show in the message center of the thermostat. The numbers are also included on a card packed with the thermostat or on the back of the thermostat (visible when removed from wallplate). Each thermostat has a unique MAC ID and MAC CRC. QQ: My thermostat is unable to register to the Total Connect Comfort website. AA: Verify that the thermostat is correctly enrolled on your homeWi-Fi network.
Frequently asked questions QQ: I registered on the Total Connect Comfort website but was unable to login using my new account. AA: Check your email and ensure that you received an activation email. Follow the instructions to activate your account and then login to the website. QQ: I have signed up on Total Connect Comfort website and have not received a confirmation email. AA: Check for the email in your Junk or Deleted folder.
Message center messages The Message Center at the top of the screen communicates Wi-Fi connection and registration status. It also displays the MAC ID and MAC CRC for registering the thermostat at mytotalconnectcomfort.com Displayed before you begin Wi-Fi setup. Displayed while connecting to the Wi-Fi network. Displayed after connecting to the Wi-Fi network. [Wi-Fi network name] Displayed when connected to the Wi-Fi network. Displayed when Wi-Fi connection is complete.
Message center messages Displayed when the thermostat is registered at mytotalconnectcomfort.com Displayed when the thermostat is removed from your Total Connect Comfort account. Wi-Fi signal strength. Displayed when the thermostat is connected to the Wi-Fi network and registered at mytotalconnectcomfort.com Displayed if there is no Wi-Fi signal. • Check another device to be sure Wi-Fi is working in your home; if not, call your Internet Service Provider. • Move the router.
Message center messages Displayed if the home Wi-Fi password is entered incorrectly. • Re-enter password for your home Wi-Fi network. • Repeat setup process and confirm your password for your home Wi-Fi network. Displayed if no IP Address is supplied by the router. • Wait for 30 minutes, connection can take several minutes. If still no connection, remove thermostat from wallplate, wait 5 seconds, and snap it back onto the wallplate.
Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • • Cannot change system setting to Cool • Check Function 0170: System Type to make sure it is set to match your heating and cooling equipment (see page 54). Fan does not turn on when heat is required • Check Function 0180: Heating Fan Control to make sure it is set to match your heating equipment (see page 55).
Troubleshooting Heat pump issues cool air in heat mode, or warm air in cool mode • Check Function 0190: Heat Pump Changeover Valve to make sure it is properly configured for your system (see page 55). Button on lower right of screen is blank • This button will remain blank unless the furnace filter change reminder is activated (see page 43). Red light is on • If thermostat is in Emergency Heat mode the red light is normal. It shows that the thermostat is in emergency heat mode.
Troubleshooting Heating or cooling system does not respond • Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM to set system to Cool. Make sure the temperature is set lower than the Inside temperature. • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely. • If “Wait” is displayed, the compressor protection timer is on.
Glossary C wire The “C” or common wire brings 24 VAC power to the thermostat from the heating/cooling system. Some older mechanical or battery operated thermostats may not have this wire connection. It is necessary for establishing a Wi-Fi connection to your home network. Heat Pump heating/cooling system Heat pumps are used to heat and cool a home. If your old thermostat has a setting for auxiliary or emergency heat, you likely have a heat pump.
Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.
Regulatory information Thermostats To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Section 7.1.
1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
69-2715ES-07 Automation and Control Systems Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 wifithermostat.com ® U.S. Registered Trademark. Apple, iPhone, iPad, iPod touch and iTunes are trademarks of Apple Inc. All other trademarks are the property of their respective owners. © 2013 Honeywell International Inc. 69-2715ES—07 M.S. Rev. 11-13 Printed in U.S.A.
Guía del usuario Termostato con pantalla táctil programable con conexión WiFi Serie Red inalámbrica (Wi-Fi) RTH8500WF
En la caja, encontrará lo siguiente: • Termostato • Placa de pared (adherida al termostato) • Tornillos y anclajes • Batería tipo botón (dentro de la parte posterior del termostato) • Guía para el encendido rápido • Tarjeta de identificación del termostato • Etiquetas de los cables • Guía del usuario 69-2715ES—07 ii
Bienvenido Felicitaciones por la compra del termostato con pantalla táctil programable con conexión WiFi de Honeywell. Cuando se registre en Total Connect Comfort Solutions de Honeywell, puede supervisar y controlar de manera remota el sistema de calefacción y refrigeración de su hogar o empresa; puede permanecer conectado a su sistema de confort dondequiera que vaya.
Este termostato funciona con sistemas comunes de 24 voltios, como aplicaciones de aire forzado, hidrónicas, de una bomba de calor, de aceite, de gas y eléctricas. No funciona con sistemas de milivoltios, como una chimenea a gas, ni con sistemas de 120/240 voltios, como la calefacción de zócalo eléctrica. Este termostato tiene una batería de litio que puede contener material con perclorato. Material con perclorato: es posible que deba aplicarse un tratamiento especial. Visite www.dtsc.ca.
Índice Acerca de su nuevo termostato Anulación permanente de los cronogramas................................... 41 Configuración del mantenimiento de la temperatura en vacaciones............... 42 Configuración de los intervalos del recordatorio del filtro............................ 43 Limpieza de la pantalla.............................. 44 Baja del termostato.................................... 45 Desconexión de la red WiFi....................... 46 Características especiales.........................
Características del termostato con conexión WiFi Con el nuevo termostato, podrá realizar lo siguiente: • Conectarse a Internet para supervisar y controlar el sistema de calefacción/ refrigeración • Ver y cambiar las configuraciones del sistema de calefacción/refrigeración • Ver y configurar la temperatura y los cronogramas • Recibir alertas por correo electrónico y obtener actualizaciones automáticas El nuevo termostato ofrece lo siguiente: • Tecnología Smart Response • Protección del compresor • Cambio aut
Referencia rápida de la pantalla de inicio Una vez que el termostato con conexión WiFi esté instalado, podrá visualizar la pantalla de inicio. Partes de esta pantalla cambiarán según cómo la vea. Para cambiar las configuraciones, solo presione suavemente el área correspondiente con el dedo.
Cronogramas de ahorro de energía predeterminados Este termostato cuenta con configuraciones del programa de ahorro de energía predeterminadas durante cuatro períodos. Si utiliza las configuraciones predeterminadas, puede reducir los gastos de calefacción/refrigeración, siempre que siga las instrucciones. Los ahorros pueden varias según la región geográfica y el uso.
Configuración del termostato Configurar el termostato con pantalla táctil programable es fácil. Está preprogramado y listo para funcionar tan pronto como se instale y se registre. 1 Instale su termostato. 2 Conéctelo a su red inalámbrica doméstica. 3 Regístrelo a través de Internet para obtener acceso remoto. Antes de comenzar, le recomendamos que mire un breve video de instalación. Utilice el QR Code en la parte delantera de esta guía o visite wifithermostat.
Instalación del termostato Es posible que necesite las siguientes herramientas para instalar el termostato: • • • • • • Martillo (opcional) • Cinta aislante (opcional) Destornillador Phillips n.° 2 Destornillador de bolsillo pequeño Lápiz Nivel (opcional) Taladro y brocas (3/16” [4.8 mm] en paneles de yeso, 7/32” [5.5 mm] en yeso) (opcional) o 1 DESCONECTE la energía de su sistema de calefacción/refrigeración.
Instalación del termostato 2 Retire el termostato existente. Si el termostato existente tiene un tubo de mercurio sellado, vaya a la página 2 para obtener instrucciones sobre cómo desecharlo adecuadamente. 2a Tome una fotografía de las conexiones de los cables para usar de referencia más adelante. 2b Si ningún cable está conectado al terminal con la marca C o no existe un terminal C en el termostato existente, mire el video Alternate Wiring (Cableado alternativo) en wifithermostat.
Instalación del termostato 3 Etiquete los cables. No etiquete por color del cable. Utilice las etiquetas adhesivas suministradas para identificar cada cable a medida que los desconecta. Etiquete los cables conforme a las designaciones de los terminales del termostato existente, no según el color de los cables. Etiqueta autoadhesiva Etiquetas en blanco Nota: Si ninguna etiqueta coincide con una designación de terminal, escriba la letra correspondiente en una etiqueta autoadhesiva en blanco.
Instalación del termostato 5 Separe el termostato con conexión WiFi y la placa de pared. Termostato En el nuevo termostato, sostenga, con una mano, la placa de pared desde los orificios de sujeción en la parte superior e inferior y, con la otra, el termostato (frente). Separe las piezas.
Instalación del termostato 6 Monte la placa de pared para termostato con conexión WiFi. Monte la nueva placa de pared con los tornillos y anclajes incluidos con el termostato. Placa de pared Si fuese necesario: HEAT PUMP CONVENTIONAL Taladre agujeros de 3/16 in (4.8 mm) en paneles de yeso. Y2 RC L E/AUX W2 W K K Taladre agujeros de 7/32 in (5.6 mm) en yeso. Note: puede usar los tarugos de pared existentes. Sostenga la placa de pared con los tarugos existentes para controlar la alineación.
Instalación del termostato ¡Importante! el termostato con conexión WiFi requiere de un cable C para que funcione. El cable C, o común, le transmite 24 V CA al termostato. Muchos termostatos mecánicos o con batería más antiguos no requieren de un cable C. Si no tiene un cable C, intente hacer lo siguiente: • Busque un cable sin usar que esté introducido en la pared. Conecte ese cable a C y verifique que esté conectado a 24 V CA en el sistema de calefacción/refrigeración.
Instalación del termostato Cableado (sistema convencional) C G Y W R Extraiga el puente de metal solo si 7A Coloque el cableado del termostato con conexión WiFi en su tiene cables R y RC. sistema convencional. a Comience con el cable C y coloque la etiqueta autoadhesiva en el cable con las etiquetas del terminal. Debe tener un cable C. Refiérase a la página 13. HEAT PUMP CONVENTIONAL b Afloje el tornillo, inserte el cable en el borde interior del terminal, luego, ajuste el tornillo.
Instalación del termostato Cableado (sistema de bomba de calor únicamente) O 15 69-2715ES—07 MCR33529 C G Y AUX R ¿Las etiquetas no coinciden? 7B Coloque los cables del termostato con conexión WiFi a su Consulte la clave bomba de calor. para la instalación a Comience con el cable C y coloque la etiqueta autoadhesiva de cableado en el cable con las etiquetas del terminal. alternativo en las Debe tener un cable C. Refiérase a la página 13. páginas 18–19.
Instalación del termostato Cableado alternativo (sistema convencional) Utilícelo si las etiquetas de los cables no coinciden con las etiquetas de los terminales. CONVENCIONAL Nota: debe tener un cable C o equivalente. Refiérase a la página 13. Puente de metal Y2 W2 3 Y2 W2 K RC RC 1 R R 2 W W Y Y G G C C MSCR33528 Consulte las claves de 1 a 3 en la página 17.
Instalación del termostato Clave para cableado alternativo (sistema convencional) 1 Retire el puente de metal que conecta los terminales R y RC solo si debe conectar los dos, R y RC. 2 Si su termostato existente tenía cables R y RH, extraiga el puente de metal. Conecte el cable R al terminal RC, y el cable RH al terminal R. 3 No utilice el terminal K. Para uso futuro.
Instalación del termostato Cableado alternativo (sistema de bomba de calor únicamente) Utilícelo si las etiquetas de los cables no coinciden con las etiquetas de los terminales. BOMBA DE CALOR Puente de metal Nota: debe tener un cable C o equivalente. Refiérase a la página 13. Y2 5 6 7 RC 1 R L E/AUX RC R O AUX K 2 O/B 3 Y Y G 4 G C C 3 MSCR33530A 1 69-2715ES—07 18 Consulte las claves de – 7 en la página 19.
Instalación del termostato Clave para cableado alternativo (sistema de bomba de calor únicamente) 1 Deje el puente de metal que se encuentra entre los terminales R y RC en el lugar. 2 Si su termostato existente tenía cables V y VR, visite wifithermostat.com para obtener ayuda. 3 Si su termostato existente tenía cables O y B separados, conecte el cable B al terminal C. Si se conecta otro cable al terminal C, visite wifithermostat.com para obtener ayuda. Conecte el cable O al terminal O/B.
Instalación del termostato 8 Instale la batería. Inserte la batería tipo botón (incluida) observando la polaridad correcta. Nota: si la batería está correctamente colocada, sobresaldrá, de la ranura para baterías, aproximadamente, la mitad en el termostato, para poder extraerla con facilidad. Interior del termostato Esta batería mantiene la hora y la fecha durante los cortes de energía. No alimenta el termostato (se necesita el cable C).
Instalación del termostato Placa de pared 9 Conecte el termostato a la placa de pared. Alinee el termostato con la placa de pared y presiónelo para que calce en su lugar.
Instalación del termostato 10 Encienda el sistema de calefacción/ refrigeración. ¡Importante! 10a Verifique que el cable C esté conectado al termostato y al sistema de calefacción/ refrigeración. o 10b Verifique que la puerta del sistemas de calefacción/ refrigeración esté bien cerrada. 10c Vuelva a ENCENDER su sistema de calefacción/ refrigeración en la caja de interruptores de circuito o su interruptor de energía.
Instalación del termostato 11 Configure la fecha y la hora. Toque los botones s o t para cambiar la fecha y la hora que se visualizan. Día Año Presione y sostenga un botón para cambiar una configuración rápidamente. Mes Nota: Este termostato se actualizará automáticamente para el horario de verano (si se observa en su área) y almacena toda la información de fecha/hora. Si el termostato está conectado a Wi-Fi y registrado a Total Connect Comfort, la hora actual se actualiza desde el Internet.
Instalación del termostato 12 Determine el tipo de sistema de calefacción/refrigeración. ¡Importante! El tipo del sistema de calefacción/refrigeración debe estar configurado para que el termostato funcione correctamente y no dañe el sistema. 12a Si tiene un sistema tradicional (de aire forzado de gas natural con CA), el termostato se configura de forma predeterminada para controlar este sistema.
Instalación del termostato ¡Felicitaciones! Su termostato ya funciona. 13 Pruebe el termostato. 13b Para acceder de manera remota al termostato, continúe con el “Conexión a la red WiFi” en la página“Conexión a la red WiFi” on page 26. 25 Inside MORE MCR31580 13a Presione el botón SYSTEM (SISTEMA) para cambiar a calefacción o refrigeración, e iniciar el funcionamiento. El sistema de calefacción/ refrigeración, ¿no enciende? Consulte la página 67 o las Preguntas frecuentes en wifithermostat.
Conexión a la red WiFi Para completar este paso, debe tener un dispositivo inalámbrico conectado a su red inalámbrica doméstica. Cualquiera de estos tipos de dispositivos funcionará: • Computadora tipo tablet (recomendado) • Computadora portátil (recomendado) • Teléfono inteligente Si no puede continuar... en algún momento durante este procedimiento, reinicie el termostato. Para ello, retírelo de la placa de pared, espere 5 segundos y vuelva a calzarlo en la placa de pared presionándolo.
Conexión a la red WiFi 1 Conecte el termostato. 1a Asegúrese de que el centro de mensajes del termostato muestre Wi-Fi SETUP (Configuración de la red WiFi). 1c Conéctese a la red denominada NewThermostat_123456 (el número variará). Inside MORE M31566 1b Consulte la lista de todas las redes WiFi disponibles en el dispositivo inalámbrico (computadora portátil, computadora tipo tablet o teléfono inteligente).
2 Conecte su red doméstica. 2a Abra el explorador de Internet para acceder a la página de configuración WiFi del termostato. El navegador debería dirigirlo, automáticamente, a la página correspondiente; si no lo hace, vaya a http://192.168.1.1 2b Busque el nombre de su red doméstica en esta página y selecciónela. Nota: algunos enrutadores cuentan con funciones mejoradas, como redes huésped; utilice su red doméstica.
Conexión a la red WiFi Nota: si su red WiFi no aparece en la lista de la página de configuración del termostato WiFi: • Pruebe a efectuar nuevamente un escaneo de la red presionando el botón Rescan (Volver a examinar). Esto resulta útil en áreas con mucha cantidad de redes. • Si está conectado a una red oculta, ingrese el SSID (identificador de grupo de servicio) de la red en la casilla de texto, seleccione el tipo de codificación del menú desplegable y pulse en el botón Add (Agregar).
Conexión a la red WiFi 3 Asegúrese de que su termostato esté conectado. Mire la pantalla del termostato. Verifique que el centro de mensajes muestre uno de los siguientes mensajes: CONNECTION SUCCESSFUL (Conexión exitosa) JOINED (Conectado): [NOMBRE DE LA RED WIFI] YOU ARE ALMOST DONE (Felicitaciones. Ya casi termina) REGISTER AT TOTAL CONNECT (Regístrese en Total Connect) Inside MORE M31568 El centro de mensajes en su termostato mostrará CONNECTING... (Conectando...) durante 30 segundos.
Registro del termostato en línea Para ver y configurar el termostato con conexión WiFi de manera remota, debe tener una cuenta en Total Connect Comfort. Siga los siguientes pasos. 1 Abra el sitio web Total Connect Comfort. Vaya a www.mytotalconnectcomfort.com M31570 Mire el video Wi-Fi Thermostat Registration (Registro del termostato WiFi) en wifithermostat.
Registro del termostato en línea M31571 2 Inicie sesión o cree una cuenta. Si tiene una cuenta, haga clic en Login (Iniciar sesión) – O bien – haga clic en Create An Account (Crear una cuenta) 2a Siga las instrucciones en la pantalla. 2b Revise su correo electrónico para verificar si tiene un mensaje de activación de My Total Connect Comfort. Esto puede llevar varios minutos.
Registro del termostato en línea 3 Registre su termostato con conexión WiFi. Después de que haya iniciado sesión en su cuenta My Total Connect Comfort, registre el termostato. 3a Siga las instrucciones en la Thermostat ID Card Use the MAC ID and CRC ID to register pantalla. Después de añadir la this product at mytotalconnectcomfort.
Registro del termostato en línea 3b Cuando el termostato se haya registrado correctamente, la pantalla de registro de Total Connect Comfort le mostrará el mensaje SUCCESS (registro exitoso). En el Centro de mensajes del termostato, verá el mensaje: CONGRATULATIONS! SET UP COMPLETE. (Felicitaciones. Se ha completado la configuración).
Registro del termostato en línea 3c También debe observar que su termostatomostrará la potencia de la señal. Felicitaciones! ¡Ya terminó! Ahora, puede controlar su termostato desde cualquier lugar a través de su computadora portátil, computadora tipo tablet o teléfono inteligente. Existen aplicación gratuitas disponibles para dispositivos Apple iPhone , iPad y iPod touch en iTunes o en Google Play , para todos los dispositivos Android™.
Configuración del reloj MORE Nota: Este termostato se actualizará automáticamente para el horario de verano (si se observa en su área) y almacena toda la información de fecha/hora. Si el termostato está conectado a Wi-Fi y registrado a Total Connect Comfort, la hora actual se actualiza desde el Internet. Nota: para cambiar el formato de día de la semana actual, consulte “Opciones de cronograma” en la página 53.
Configuración del ventilador 1 Presione la opción FAN (Ventilador) para seleccionar el funcionamiento del ventilador. 3 Presione DONE (Terminado) para guardar la configuración. Su selección aparece debajo de FAN (Ventilador). ON: el ventilador está siempre encendido. AUTO: el ventilador funciona solo cuando el sistema de calefacción o refrigeración está encendido.
Selección de la modalidad del sistema 69-2715ES—07 38 Inside MORE MCR31554 1 Presione SYSTEM (Sistema) para visualizar las opciones. 2 Presione SYSTEM nuevamente para seleccionar una opción. Es posible que deba presionar dos o tres veces para realizar la selección; la opción seleccionada destella. 3 Presione DONE (Terminado) para guardar la configuración. Posibles modalidades del sistema: HEAT: controla solo el sistema de calefacción. COOL: controla solo el sistema de refrigeración.
Ajuste de los cronogramas del programa MCR31555 MORE 1 Presione SCHED (Cronograma) y, luego, EDIT (Editar). La pantalla muestra los botones de los días en la parte superior. SLEEP 2 Presione los botones de los días (MON-SUN [Lun./Dom.]) para seleccionar los días. 3 Presione s o t para configurar la hora de despertarse correspondiente a los días seleccionados. 4 Presione s o t para configurar la temperatura de calefacción y refrigeración de este período.
Anulación temporal de los cronogramas 1 En la pantalla de inicio, presione s o t para ajustar inmediatamente la temperatura. La nueva configuración de mantendrá hasta la hora indicada en Hold Until (Mantener hasta). Cuando el temporizador finalice, el cronograma se reanudará y la temperatura volverá a la configuración correspondiente al período actual. Para cancelar la configuración temporal en cualquier momento, presione CANCEL (Cancelar) o SCHED (Cronograma). El cronograma del programa se reanudará.
Anulación permanente de los cronogramas 1 Presione HOLD (Mantener) para ajustar permanentemente la temperatura. Esto desactivará el cronograma del programa. 2 Independientemente de la temperatura que configure, esta se mantendrá durante las 24 horas hasta que usted la modifique manualmente o presione CANCEL (Cancelar) (o SCHED [Cronograma]) para cancelar el “reposo” y reanudar el cronograma del programa.
Configuración del mantenimiento de la temperatura en vacaciones 69-2715ES—07 42 MORE MORE MCR31558 Inside Utilice esta función para suspender el cronograma del programa mientras usted se encuentre fuera de su hogar durante un período prolongado. 1 Presione s o t para configurar la temperatura. Hold Until 2 Presione s o t para configurar la hora del día en la que quiere que el cronograma se reanude cuando usted regrese. 3 Presione HOLD dos veces. Aparecerá la opción Hold Until (Mantener hasta).
Configuración de los intervalos del recordatorio del filtro Si se activa durante la instalación, el recordatorio del filtro le envía un mensaje que figura sobre la hora que le indica que es momento de cambiar su filtro. Presione RESET (Reiniciar) después de cambiar el filtro para reiniciar el temporizador. Inside RESET CHANGE FILTER Para cambiar el intervalo del recordatorio: MORE 1 Presione MORE (Más) y, luego, EDIT (Editar).
Limpieza de la pantalla 1 Presione SCREEN (Pantalla) para bloquear la pantalla para realizar la limpieza. La pantalla permanecerá bloqueada durante 30 segundos para que pueda limpiarla sin modificar ninguna configuración. MORE Nota: NO rocíe ningún líquido directamente sobre el termostato. Rocíe el líquido sobre un paño, después utilice el paño húmedo para limpiar la pantalla. Utilice agua o el limpiador para vidrios que utiliza en casa. Evite utilizar limpiadores abrasivos.
Baja del termostato Después de eso, alternará al mostrar el mensaje REGISTER AT TOTAL CONNECT (Inscribirse en Total Connect), el MAC ID y el MAC CRC. 45 Inside MORE M31572 Si usted retira el termostato de su cuenta en el sitio web Total Connect Comfort (por ejemplo, si se muda y deja el termostato), el Centro de mensajes mostrará el mensaje UNREGISTERED FROM TOTAL CONNECT (Dado de baja de Total Connect) durante 3 minutos.
Desconexión de la red WiFi Cambio de su enrutador Si usted desconecta el termostato de su red WiFi: 1 Ingrese a la configuración del sistema (consulte la página 51). 2 Cambie la configuración de 900 a 0 (consulte la página 58). El Centro de mensajes mostrará el mensaje Wi-Fi DISCONNECTED (WiFi desconectada) durante un minuto. Después, le mostrará el mensaje Wi-Fi SETUP (Configuración de la red WiFi). Para volver a conectarse a una red WiFi, siga los pasos en la página 26.
Honeywell realiza actualizaciones periódicas del software para este termostato. Las actualizaciones se efectúan automáticamente a través de su conexión WiFi. Todas sus configuraciones permanecen guardadas, de modo que no necesita hacer cambios después de que ocurra la actualización. M34184 Actualizaciones del software Mientras ocurre la actualización, la pantalla del termostato queda en blanco y el centro de mensajes muestra UPDATING (actualizando) y el porcentaje de la actualización que ha ocurrido.
Tecnología Smart Response Esta característica permite que el termostato “sepa” cuánto demora el sistema de calefacción/refrigeración en alcanzar las configuraciones de temperatura programadas, de manera que se alcance esa temperatura a la hora que usted configuró. Por ejemplo: Configure la hora de despertarse a las 6:00 a.m. y la temperatura en 70 °F. La calefacción se encenderá antes de las 6:00 a.m., para que la temperatura esté en 70 °F a las 6:00 a.m.
Protección del compresor Esta característica hace que el compresor demore unos minutos antes de volver a iniciarse, para evitar daños al equipo. Durante el tiempo de espera, el mensaje “Wait” (Esperar) se muestra en la pantalla.
Conversión automática Esta función se usa en climas en donde el acondicionador de aire y la calefacción se utilizan durante el mismo día. Cuando el sistema está configurado en AUTO (Automático), el termostato elige automáticamente cuándo calentar o refrigerar, según la temperatura interior. El termostato ajustará automáticamente las configuraciones para mantener esta diferencia de 3 grados. Nota: la función de configuración del sistema 0300 controla la conversión automática.
Opciones y funciones de configuración Puede cambiar las opciones en diversas funciones del sistema. Las funciones disponibles dependen del tipo de sistema que usted tenga. Las funciones, designadas con números de cuatro dígitos, junto con las opciones disponibles se describen en las páginas 52–58. Este termostato está preconfigurado para un sistema de calefacción/refrigeración de una sola etapa. La función de configuración 0170 para la bomba de calor ajustará las configuraciones predeterminadas.
Configuración del sistema ¿Cómo configuro el nombre de mi termostato? (Consulte la página 51 para obtener instrucciones.) Función 0112 Configuraciones y opciones 52 = Thermostat Nombre del dispositivo 1 Basement 2 Bathroom Este nombre 3 Bathroom 1 identificará el 4 Bathroom 2 termostato cuando 5 Bathroom 3 usted lo observe de 6 Bedroom manera remota. 7 Bedroom 1 Si registra múltiples 8 Bedroom 2 termostatos, debe 9 Bedroom 3 darle a cada uno un 10 Bedroom 4 nombre diferente.
Configuración del sistema ¿Cómo cambio las configuraciones de fecha y hora? (Consulte la página 51 para obtener instrucciones.) Función 0120 Configuraciones y opciones Configuración del año (primeros dos dígitos) Configuración del año (últimos dos dígitos) 20 = Año 20xx 21 = Año 21xx 0140 Configuración del mes 01–12 (por ej., enero a diciembre) 0150 Configuración de la 01–31 fecha 4 El cronograma del programa está activado (programable para 7 días).
Configuración del sistema ¿Cómo configuro el tipo de sistema de calefacción/refrigeración? (Consulte la página 51 para obtener instrucciones.) Función Configuraciones y opciones 0165 Recuperar configuraciones predeterminadas 0 1 0170 Seleccionar el tipo de sistema Si no está seguro sobre el tipo de sistema de calefacción/ refrigeración que tiene o si tiene alguna otra pregunta, visite wifithermostat.com 1 Calor/frío: Calefacción a gas, aceite o eléctrica con aire acondicionado central.
Configuración del sistema ¿Cómo personalizo el tipo de sistema de calefacción/refrigeración? (Consulte la página 51 para obtener instrucciones.) Función Configuraciones y opciones Nota: según las configuraciones del sistema, es posible que las funciones de esta página no aparezcan. 0180 Control del ventilador de calefacción 0 Calefacción a gas o aceite: Utilice esta configuración si tiene un sistema de calefacción a gas o aceite (el sistema controla el funcionamiento del ventilador).
Configuración del sistema ¿Qué otras funciones puedo modificar? (Consulte la página 51 para obtener instrucciones.) Función Configuraciones y opciones Iluminación de fondo 0 0300 Cambio manual/ automático Consulte la página 50 para obtener más información. 0 1 0320 0 Formato de la temperatura (°F/°C) 1 0330 Ajuste de horario de verano automático 0280 69-2715ES—07 1 0 1 La luz de fondo se apaga y, luego, se enciende durante, aproximadamente, 8 segundos después de presionar la tecla.
Configuración del sistema ¿Qué otras funciones puedo modificar? (Consulte la página 51 para obtener instrucciones.) Función Configuraciones y opciones 0500 Recordatorio de cambio del filtro El recordatorio aparece después de la cantidad de días seleccionados de tiempo de funcionamiento, no del tiempo real. 0 Apagado (sin recordatorio) Recordatorio después de: 1 10 días de tiempo de funcionamiento (aprox., 1 mes calendario) 2 30 días de tiempo de funcionamiento (aprox.
Configuración del sistema ¿Cómo cambio las configuraciones de la red WiFi? (Consulte la página 51 para obtener instrucciones.) Función Configuraciones y opciones 0710 Restaurar configuraciones originales 0 1 0890 WiFi encendida/ apagada 1 0 La red WiFi está encendida y puede conectarse a una red WiFi. La red WiFi está apagada. No se puede conectar el termostato a una red WiFi.
Preguntas frecuentes PP: ¿Mi termostato seguirá funcionando si pierdo la conexión a la red WiFi? RR: Sí, el termostato pondrá en funcionamiento el sistema de calefacción o refrigeración con o sin la conexión a la red WiFi. PP: ¿Cómo encuentro la contraseña de mi enrutador? RR: Comuníquese con el fabricante del enrutador o revise la documentación del enrutador. PP: ¿Por qué no puedo ver la página de configuración de la red WiFi? RR: Probablemente, esté conectado solo a su enrutador, y no al termostato.
Preguntas frecuentes PP: ¿Dónde puede encontrar mis códigos MAC ID y MAC CRC? RR: Los códigos MAC ID y MAC CRC aparecerán en el Centro de mensajes del termostato. Los números también se incluyen en una tarjeta que se ofrece con el termostato o que se encuentra en la parte posterior del termostato (visible cuando se extrae de la placa de pared). Cada termostato tiene un MAC ID y un MAC CRC únicos. PP: No puedo registrar mi termostato en el sitio web Total Connect Comfort.
Preguntas frecuentes PP: Me registré en el sitio web Total Connect Comfort, pero no pude iniciar sesión con mi nueva cuenta. RR: Revise su correo electrónico y asegúrese de haber recibido un mensaje de activación. Siga las instrucciones para activar su cuenta y, luego, inicie sesión en el sitio web. PP: Me he registrado en el sitio web Total Connect Comfort y no he recibido un correo electrónico de confirmación. RR: Revise que el correo electrónico no esté en la carpeta Correo no deseado o Eliminados.
Mensajes del Centro de mensajes El Centro de mensajes, que se encuentra la parte superior de la pantalla, informa el estado de la conexión WiFi y de registro. También muestra el MAC ID (Número de identificación personal MAC) y el MAC CRC (Número de identificación personal CRC) para registrar el termostato en mytotalconnectcomfort.com Se muestra antes de iniciar la configuración de la conexión WiFi. Se muestra mientras se está conectando a la red WiFi.
Mensajes del Centro de mensajes Se muestra cuando el termostato está registrado en mytotalconnectcomfort.com Se muestra cuando se retira el termostato de su cuenta en Total Connect Comfort. Potencia de la señal WiFi. Se muestra cuando el termostato está conectado a la red WiFi y está registrado en mytotalconnectcomfort.com Se muestra si no hay señal Wi-Fi. • Revise otro dispositivo para verificar que la conexión Wi-Fi está funcionando en su hogar; si no, llame a su proveedor de Internet.
Mensajes del Centro de mensajes Se muestra si la contraseña doméstica de Wi-Fi se ingresa incorrectamente. • Vuelva a ingresar la contraseña de su red doméstica WiFi. • Repita el proceso de configuración y confirme su contraseña de la red doméstica de WiFi. Se muestra si el enrutador no suministra la dirección IP. • Espere 30 minutos, puede tomar algunos minutos que se realice la conexión. Si aún no hay conexión, retire el termostato de la placa de pared durante 5 segundos y luego conéctelo nuevamente.
Localización y solución de problemas Si tiene dificultades con el termostato, intente seguir las sugerencias que se indican a continuación. La mayoría de los problemas pueden solucionarse de manera fácil y rápida. La pantalla está en blanco • Revise el interruptor de circuito y, si es necesario, reinícielo. • Asegúrese de que el interruptor de energía del sistema de calefacción y refrigeración esté encendido. • Asegúrese de que la puerta del sistema de calefacción esté bien cerrada.
Localización y solución de problemas Los problemas con la bomba de calor hacen que se enfríe el aire en la modalidad de calefacción, o que se caliente el aire en la modalidad de refrigeración • Verifique Función 0190: válvula de cambio de la bomba de calor, para cerciorarse de que esté bien configurada según su sistema (consulte la página 55).
Localización y solución de problemas El sistema de calefacción o refrigeración no responde • Presione SYSTEM (Sistema) para configurar el sistema en Heat (Calefacción). Asegúrese de que la temperatura sea más alta que la temperatura interior. • Presione SYSTEM (Sistema) para configurar el sistema en Cool (Refrigeración). Asegúrese de que la temperatura sea más baja que la temperatura interior. • Revise el interruptor de circuito y, si es necesario, reinícielo.
Glosario Cable C El cable “C”, o común, le transmite 24 V CA al termostato desde el sistema de calefacción/refrigeración. Es posible que algunos termostatos mecánicos o con batería más antiguos no tengan esta conexión de cables. Es necesario para establecer una conexión de la red WiFi a su red doméstica. Sistema de refrigeración/calefacción de bomba de calor Las bombas de calor se utilizan para calentar y refrigerar una casa.
Información sobre normativas Declaración de conformidad con las regulaciones FCC (Sección 15.19) (solo en los EE. UU.) Este dispositivo cumple con la Sección 15 de las regulaciones FCC. El funcionamiento está sujeto a las dos condiciones siguientes: 1 Este dispositivo no debe causar interferencia perjudicial, y 2 Este dispositivo deberá aceptar cualquier interferencia que se reciba, incluso la interferencia que pudiese causar el funcionamiento no deseado. Advertencia de la FCC (Sección 15.
Información sobre normativas Termostatos Para cumplir con los límites de exposición RF que establece la FCC y el Industry Canada para la población en general/exposición no controlada, la o las antenas usadas para estos transmisores deben instalarse a una distancia de, al menos, 20 cm de todas las personas, y no deben ubicarse ni utilizarse junto con otra antena o transmisor. Sección 7.1.
Garantía limitada de 1 año Honeywell garantiza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricación o de los materiales, a partir de la fecha de compra por parte del consumidor. Si en cualquier momento durante el período de garantía se verifica que el producto tiene un defecto o que funciona mal, Honeywell lo reparará o reemplazará (a elección de Honeywell).
69-2715ES-07 Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 wifithermostat.com ® Marca Registrada en los E.U.A. Apple, iPhone, iPad, iPod touch y iTunes son marcas comerciales de Apple Inc. Todas las demás marcas comerciales son propiedad de sus respectivos dueños. © 2013 Honeywell International Inc. 69-2715ES—07 M.S. Rev. 11-13 Impreso en EE. UU.