S9200U Installation Guide
Table Of Contents
- Application
- Features
- Specifications
- Installation and Configuration Overview
- Cross Reference
- Installation
- Safety Timings, Field Settings, and Fixed Parameters
- Thermostat Type
- Twinning
- Checkout
- I. Check Normal Operation
- II. Check Safety Shutoff Operation
- Troubleshooting
- Application
- CARACTÉRISTIQUES
- SPÉCIFICATIONS
- APERÇU DE L'INSTALLATION ET DE LA CONFIGURATION
- CORRESPONDANCES
- Installation
- TEMPORISATIONS DE SÉCURITÉ, RÉGLAGES DE COMMUTATEUR SUR SITE ET DE PARAMÈTRES FIXES
- TYPE DE THERMOSTAT
- PAIRAGE
- VÉRIFICATION
- I. VÉRIFICATION DU FONCTIONNEMENT NORMAL
- II. VÉRIFICATION DE LA COUPURE DE SÉCURITÉ
- DÉPANNAGE
S9200U1000 UNIVERSAL HOT SURFACE IGNITION INTEGRATED FURNACE CONTROL
69-2075EF—05 2
INSTALLATION AND
CONFIGURATION
OVERVIEW
The following is an overview of the steps required to
install and configure the S9200U1000 Integrated
Furnace Control:
1. Identify cross reference target using Table 1.
2. Remove old device and carefully identify and
mark any wiring. See “Replacement” on page 7.
3. Mount the S9200U1000 Integrated Furnace
Control. See “Replacement” on page 7.
4. Connect the wiring harnesses and make the wir-
ing connections. See “Wiring” on page 7.
5. Configure the field settings and safety timings.
See “Safety Timings, Field Settings, and Fixed
Parameters” beginning on page 11.
CROSS REFERENCE
IMPORTANT
Only use the S9200U1000 on 120 Vac
applications.See Table 1 for the replacement
details for other manufacturers’ controls. See
Table 2 for replacement details for Trane
controls.
Table 1. S9200U1000 Replaces These Integrated
Furnace Controls.
SKU Harness
Field Settings
Recommendation
- DIP Switch S1
Safety Timing
Settings -
DIP Switch S2
United Technologies
1012-925A D
Main
Connector
C
Inducer & HSI
Connector
SW1: ON
SW2: OFF
SW3 & SW4:
60/90/120/180
SW1: ON
SW2: ON
1012-925B
1012-925C
Rheem/ Robert Shaw
62-24268-01 D
Main
Connector
C
Inducer & HSI
Connector
SW1: ON
SW2: OFF
SW3 & SW4:
60/90/120/180
SW1: ON
SW2: ON
62-24268-02
62-24268-03
695-200
Nordyne
624557 D
Main
Connector
B
Inducer & HSI
Connector
SW1: ON
SW2: OFF
SW3 & SW4:
60/90/120/180
SW1: ON
SW2: OFF
6245570
624557-0
624564
6245640
624591
624591A
624591-A
624591-B
624591-C
624591-D
624628
624628-0
6246310
624631-0
624631A
624631-A
624631-B
710128A
902378
902696
903106
CAR903106
United Technologies
1012-955A D
Main
Connector
B
Inducer & HSI
Connector
SW1: ON
SW2: OFF
SW3 & SW4:
60/90/120/180
SW1: ON
SW2: OFF
1012955A
Texas Instruments
6DT-1 A
Inducer & HSI
Connector
SW1: ON
SW2: OFF
SW3 & SW4:
60/90/120/180
SW1: OFF
SW2: ON
6DT-2
61F3
Table 1. S9200U1000 Replaces These Integrated
Furnace Controls. (Continued)
SKU Harness
Field Settings
Recommendation
- DIP Switch S1
Safety Timing
Settings -
DIP Switch S2