Full Product Manual

INSTALLATION INSTALLATIONSAFETY INFORMATION
PRE-INSTALLATION
IMPORTANT: Read all safety precautions and installations carefully before installing or
servicing this fixture.
• 5.25’ power cord with plug, link up to 4 shoplight together.
• Do not handle any energized fixture or attempt to energize any fixture with wet hands or while
standing on a wet or damp surface or in water.
• Assure that the fixture is mounted onto a structurally sound surface that will support the
fixture.
• The fixture is designed for use in a 120 VAC, 60Hz fused circuit. Do not use on a dimming
circuit.
• Do not look into the lights.
• Product is intended for use in garages, basements, work areas, utility rooms and recreation
rooms.
• Maximum distance to the receptacle is determined by the length of the cord provided.
(5.25 ft, 3-prong, 120V grounded plug included)
• Includes a protective sleeve, such as 0.010-inch (0.25-mm) thick fiberglass, where the path
of cord travel to the ceiling-mounted receptacle is not between the two supporting chains.
• The fixture is intended to be installed directly beneath a ceiling-mounted receptacle. Excess
cord should be secured to one of the supporting chains with a cable tie to keep it out of the
work space.
• Use hook to support chain, not the electrical cord.
• Do not install on radiant-heating type ceiling.
• Maximum distance to the receptacle is determined by the length of cord provided.
WARNING: Failure to comply with these instructions could result in a potentially fatal electric
shock and/or property damage.
• Carefully remove the fixture from the carton and check to make sure that all hardware is included.
• Be careful not to misplace any of the hardware needed for installing the fixture. If all hardware is
not included, call customer service number.
PLANNING INSTALLATION
HARDWARE INCLUDED
NOTE: The unit is intended to be installed directly beneath a ceiling-mounted receptacle. If
there is excess cord, bind with string or a cable tie to keep it out of work space.
ATTACH THE CEILING HOOKS
Choose desired location of light fixture making sure it is within reach of an outlet. Use a pencil
to place a mark on the ceiling where each ceiling hook (Part CC) should go. Screw hooks in
place until secure.
ATTACH THE “S” HOOKS
Insert the “S” hooks (Part BB) into each of the holes on both sides of the shop Light.
(Figure 1)
CONNECTION OPTIONS
NOTE: A maximum of 10 lights can be connected off of a single circuit.
1. LINKING CABLE
Multiple lights can be connected using the 5.25" power cord. Once installed,
plug the power cord into the end of linked shop light and repeat to add more
lights.
ATTACH THE HANGING CHAIN
1. Using two hanging chains (Part AA) attach a hanging chain to one of the “S” hooks (Part BB)
previously attached to each side of the light fixture. (Figure 2)
NOTE: The hanging chain must be bent in half in order to attach each side to an “S” hook.
2. Attach two additional “S hooks” (Part BB) to the center of each hanging chain previously attached.
3. Attach the remaining hanging chains (Part AA) to the “S” hooks (Part BB) previously attached.
4. Adjust chain manually to achieve desired height.
5. Attach the remaining “S” hooks (Part BB) to the hanging chains and attach to the ceiling hooks.
6. Determine whether a single or multiple lights are to be installed. If multiple lights will be
installed follow steps in CONNECTION OPTIONS section. Connect lights per instructions and
repeat steps 1-5 (under Attach the Hanging Chain) for each light connected.
7. Plug power cord into an outlet to use pull chain to power on.
AA: 12 in. Hanging Chain (4)
Maximum Weight: 7 kgs.
BB: “S” Hook (8)
2.0 mm x 25.4 mm x 11.6 mm
CC: Ceiling Hook (2)
3.0 mm x 54.5 mm x 15.6 mm
(Figure 1)
17”
11”
Fold Fold
Fold Fold
(Figure 2)
Connect the power cord
plug to shoplight
AC Outlet