Datasheet

ManualsBrandsHONEYWELL ManualsSensorsAngle and tilt sensor Reading range: 0 - 180 ° M12 (4-pin)

SIZE

DRAWING NAME

SHEET

TITLE

SCALE

THIS DRAWING COVERS A PROPRIETARY ITEM

AND IS THE PROPERTY OF HONEYWELL.

THIS DRAWING IS NOT TO BE COPIED OR USED

WITHOUT THE PERMISSION OF HONEYWELL.

TOLERANCES UNLESS NOTED:

DRAWN

CHECK

Pro/ENGINEER

REV

TYPE

HONEYWELL

PART NUMBER

FO-55117-B

CAGE CODE

LINEARITY #0.4%

OF FULL SCALE

ANGLE

LINEARITY #0.4%

OF FULL SCALE

23.85 #0.1

5.9 #0.1

9.99 #0.05

(52.23 )

130.3

(R )95

AIRGAP

8.58 #2.5

6.7 #0.05

0.4 A B C

2X 6.7 #0.05

(22.5 )

4.45 #2.5

(79.85 )

54.35

95.26

190.53

(3)

(35.4 )

( )90 $

JLH 9JUN10

SMART POSITION SENSOR, 180 ARC

1 OF 1

1:1

REV

DOCUMENT

CHANGED BY CHECK

E 0076277 MBN 08APR11 DSK

SPS-A180D-HAMS

INTERPRET PER ASME Y14.5M-1994

OTHER HONEYWELL ENGINEERING

STANDARDS MAY APPLY

DESIGN UNITS: MM

I - SPS-A180D-HAMS E

SENSOR OUTPUT PERFORMANCE

PARAMETER MIN TYP MAX UNITS

SENSITIVITY 21.33 22.22 23.11 mV/DEGREE

MEASUREMENT DISTANCE 0 180 DEGREES

% LINEARITY -0.4 0 0.4 % FS

REF POINT "B"

MEASUREMENT ANGLE (DEGREES)

OUTPUT VOLTAGE (VOLTS)

PIN 2

NOMINAL SIGNAL OUTPUT CURVE

(THROUGH REFERENCE POINTS "A" AND "B")

0.5

4.5

4.75

SENSOR OUTPUT PERFORMANCE CHART

180 $

0$

REF POINT "A"

1.0

2.0

3.0

4.0

DEFINITIONS:

1 - % LINEARITY SHALL BE THE QUOTIENT OF THE MEASURED OUTPUT DEVIATION FROM THE BEST FIT LINE AT

THE MEASURED TEMPERATURE TO THE FULL SCALE OUTPUT SPAN

2 - % LINEARITY = (MEASURE VOLTAGE @ T - INDEX VOLTAGE [DEFINED BY BEST FIT LINE @ T]) / (FULL SCALE OUTPUT SPAN) X 100

3 - FS = FULL SCALE = 4 V

NOTES:

1 - PIN 2 IDEAL OUTPUT @ REF POINT A [ANGLE =0 $]: 0.5V

IDEAL OUTPUT @ REF POINT B [ANGLE =180 $]: 4.5V

2 - PIN 4 IDEAL OUTPUT @ REF POINT C [ANGLE =0 $]: 4.5V

IDEAL OUTPUT @ REF POINT D [ANGLE =180 $]: 0.5V

3 - OPERATING CONDITIONS:

TEMP RANGE -40 $C TO 85 $C

SUPPLY VOLTAGE 6.0 TO 24.0 VDC

SUPPLY CURRENT 45mA MAX

4 - MOUNTING

MAGNET PIN LOCATING HOLE: 10.25 # 0.10

MOUNTING SCREWS: 1/4-20 OR M6

RECOMMENDED INSTALLATION TORQUE: 53.1 TO 70.8 IN-LBS (6 TO 8 N-M)

5 - CONNECTOR PINOUT:

PIN 1: SUPPLY VOLTAGE (+) PIN 2: OUTPUT

PIN 3: GROUND (-) PIN 4: INVERTED OUTPUT

ONLY OUTPUT PIN 2 OR PIN 4 CAN BE CONNECTED AT A TIME

6 - FERROUS MATERIAL WITHIN 100 MM (3.9") RADIUS OF MAGNET MAY IMPACT SENSOR PERFORMANCE

7 - DIAGNOSTIC - MAGNET OUT OF RANGE: PIN 2 > 4.55, PIN 4 < .45

8 - TOLERANCE APPLIES FOR FULL SENSE RANGE

9 - DEVICE USED TO READ ANALOG OUPUT MUST HAVE INPUT IMPEDANCE GREATER THAN 1 MEGAOHM

10 - OUTSIDE OF THE VALID MEASUERMENT RANGE THE OUTPUT VOLTAGE WILL BE INDETERMINATE

11 - DIRECT IMPACT TO THE CONNECTOR MAY COMPROMISE THE INTEGRITY OF THE SENSOR AND COMPROMISE

THE SEAL RATING. HONEYWELL ADVISES MEASURES BE ESTABLISHED TO PREVENT DIRECT IMPACT.

0.25

REF POINT "C"

PIN 4

NOMINAL SIGNAL OUTPUT CURVE

(THROUGH REFERENCE POINTS "C" AND "D")

REF POINT "D"

SEE DETAIL

(0 $)

(180 $)

CABLE DIRECTION FOR

RIGHT ANGLE CONNECTOR

M12 (4 POS) CONNECTOR

A-KEYED PER IEC 61076

DETAIL

SCALE 3:1

Summary of content (8 pages)

PAGE 1
8 FO-55117-B HONEYWELL PART NUMBER SPS-A180D-HAMS 7 5 6 1 2 REF POINT "B" REF POINT "C" DEFINITIONS: 1 - % LINEARITY SHALL BE THE QUOTIENT OF THE MEASURED OUTPUT DEVIATION FROM THE THE MEASURED TEMPERATURE TO THE FULL SCALE OUTPUT SPAN 2 - % LINEARITY = (MEASURE VOLTAGE @ T - INDEX VOLTAGE [DEFINED BY BEST FIT LINE 3 - FS = FULL SCALE = 4 V 4.75 4.5 OUTPUT VOLTAGE (VOLTS) 3 SENSOR OUTPUT PERFORMANCE CHART F E 4 LINEARITY #0.
PAGE 2
SMART Position Sensor, 100 and 180 Arc Configurations DESCRIPTION The Honeywell SMART Arc Position Sensor is one of the most durable, adaptable, lightweight, and non-contact position sensors available, enabling absolute position sensing with enhanced accuracy. This simple, robust, arc position sensor offers an IP69K sealed package, eliminating mechanical failure mechanisms, reducing wear and tear, improving reliability and durability, and minimizing downtime.
PAGE 3
Transportation Aerial work lift platform, front end loader and digger/excavator boom position Scissor lift position Refuse truck lift and automatic reach arm position Mobile crane steering Timber harvester/processor equipment cutter arm angle On-board loader weighing system position Industrial Telescoping conveyor elevation Power generation contact angle Rail-road crossing arms position Military Remote weapon systems elevation Chassis suspension systems position height Military vehicle door position Aerosp
PAGE 4
Figure 1. Dimensional Drawings (For reference only: mm/[in].
PAGE 5
Figure 1. Dimensional Drawings (For reference only: mm/[in], continued.) SPS-A100X-LAAS0401 A = Magnet pin locating hole B = Partial view C = Rotating axis center D = Magnetic sensitive zone: protect with a non-ferrous metal shield 4 sensing.honeywell.
PAGE 6
Figure 1. Dimensional Drawings (For reference only: mm/[in], continued.) SPS-A180D-HAMS, SPS-A180D-VAMS A = Cable direction for right angle connector B = Polyethylene conduit Figure 2.
PAGE 7
Figure 3. Sensor Output Performance Chart Showing Ideal Outputs (Applies to all catalog listings.) REF POINT "C” REF POINT "B" LINEARITY ±0.4% OF FULL SCALE 4.75 4.5 Output Voltage (V) 4.0 PIN 2, GREEN WIRE LEAD NOMINAL SIGNAL OUTPUT CURVE (THROUGH REFERENCE POINTS "A" AND "B") 3.0 2.0 PIN 4, BLUE WIRE LEAD NOMINAL SIGNAL OUTPUT CURVE (THROUGH REFERENCE POINTS "C" AND "D") 1.0 LINEARITY ±0.4% OF FULL SCALE 0.5 0.
PAGE 8
Order Guide Catalog Listing SPS-A100D-HAMS SPS-A100D-VAMS SPS-A100D-HAWS SPS-A100X-LAAS0401 SPS-A180D-HAMS SPS-A180D-VAMS Description SMART Position Sensor, 100 arc configuration, 0 to 100 inside sensing range, 6 Vdc to 24 Vdc supply voltage, 0.5 Vdc to 4.5 Vdc analog output, 4-pin M12 connector, magnet actuator included SMART Position Sensor, 100 arc configuration, 0 to 100 inside sensing range, 18 Vdc to 40 Vdc supply voltage, 0.5 Vdc to 4.