T8775A,C The Digital Round™ Non-Programmable Thermostats OWNER’S GUIDE ® U.S. Registered Trademark Patents Pending © 2004 Honeywell International Inc.
(T8775C ONLY) SELECTS ON/AUTO (T8775C ONLY) SELECTS COOL/OFF/HEAT ROOM SET SHOWS THAT THE CURRENT ROOM TEMPERATURE IS DISPLAYED. SHOWS THAT THE CURRENT TEMPERATURE SETTING IS DISPLAYED. DISPLAYS ROOM OR SET TEMPERATURE DISPLAYS AND ADJUSTS TEMPERATURE SETTING/TURNS BACKLIGHT ON M19470 Fig. 1. T8775 Thermostat (features and operation).
Setting SYSTEM and FAN Switches (T8775C only) ❑ System and Fan settings are controlled by using SYSTEM and FAN switches located on the top of the thermostat (see Fig. 1). IMPORTANT Do not operate the T8775C in cooling mode when the outdoor temperature is below 50°F (10°C), or damage to compressor could result. SET THE SYSTEM SWITCH: ❑ Heat: The thermostat controls your heating system. ❑ Off: Both heating and cooling systems are off. ❑ Cool: The thermostat controls your cooling system.
Backlit Display ❑ The backlight can be turned on by turning the dial, or by pushing the backlight button as shown in Fig. 1. Display Temperature Setting NOTE: Your temperature setting can be set anywhere from 40°F to 90°F (4°C to 32°C) in heating and 45°F to 99°F (7°C to 37°C) in cooling (T8775C only). ❑ Turn the dial one click to display the current temperature setting. A indicator points to Set when the temperature setting is displayed.
Adjust Temperature Setting ❑ To lower the temperature setting, turn the dial counterclockwise. ❑ To raise the temperature setting, turn the dial clockwise. Troubleshooting Guide CAUTION Equipment Damage Hazard. Can cause permanent damage to compressor or other equipment. Do not operate cooling when outside temperature is below 50°F (10°C). Allow compressor to remain off for five minutes before restarting. See equipment manufacturer instructions. Heating or cooling does not come on.
❑ In heating, make sure the temperature setting is above the room temperature and the flame is present in the display. ❑ In cooling, make sure the temperature setting is below the room temperature and a solid snowflake is present in the display (T8775C only). NOTE: If a call for cooling is made before the compressor has been off for five minutes, or if a power interruption occurs while the compressor is running, the thermostat will go into a five-minute delay to protect the compressor.
69-1679ES—1
Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 69-1679ES—1 J.S. Rev. 6-04 Printed in Mexico Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 www.honeywell.
Termostatos no programables T8775A, C The Digital Round™ GUÍA DEL PROPRIETARIO ® Marca Registrada en los E.U.A Patentes pendientes © 2004 Honeywell International Inc.
Fig. 1. Termostato T8775 (características y operación).
Cómo ajustar los interruptores SYSTEM (SISTEMA) y FAN (VENTILADOR) (sólo T8775C) ❑ Los ajustes del sistema y el ventilador se controlan por medio de los interruptores SYSTEM y FAN que están situados en la parte superior del termostato (vea la Figura 1). IMPORTANTE No opere el termostato T8775C en modo de enfriamiento cuando la temperatura exterior sea menor de 50°F (10°C), pues se podrнa daсar el compresor.
AJUSTE DEL INTERRUPTOR DEL VENTILADOR: ❑ Auto(mático): Ajuste normal para la mayoría de las casas. El ventilador solamente funciona con el sistema de calefacción y de enfriamiento. ❑ On (Encendido): El ventilador funciona continuamente. Se usa para tener una mejor circulación de aire. Operación del termostato NOTE: No se requieren baterías, puesto que el ajuste de temperatura se mantiene de modo permanente en la memoria.
Ajuste de temperatura de la pantalla NOTA: El ajuste de temperatura se puede configurar de 40°F a 90°F (4°C a 32°C) para la calefacción y de 45°F a 99°F (7°C a 37°C) para el enfriamiento (sólo T8775C). ❑ Gire una posición el disco graduado para mostrar el ajuste de temperatura actual. Un indicador señala Set (configurado) cuando se muestra el ajuste de temperatura. Si no se hace un cambio al ajuste de temperatura en un lapso de cinco segundos, el modo cambiará a la pantalla de temperatura ambiente.
Ajuste de la temperatura ❑ Para bajar el ajuste de temperatura, gire el disco graduado hacia la izquierda. ❑ Para subir el ajuste de temperatura, gire el disco graduado hacia la derecha. Guía para localización de problemas CAUTION Riesgo de daños al equipo Puede provocar daños permanentes al compresor o a otros equipos. No opere el modo de enfriamiento cuando la temperatura exterior sea menor de 50 °F (10 °C). Deje apagado el compresor durante cinco minutos antes de reiniciarlo.
❑ En la calefacción, asegúrese de que el ajuste de temperatura esté por arriba de la temperatura ambiente y de que se vea la flama en la pantalla. ❑ En modo de enfriamiento, asegúrese de que el ajuste de temperatura esté por debajo de la temperatura ambiente y de que se vea un copo de nieve sólido en la pantalla (sólo T8775C).
Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive Golden Valley, MN 55422 69-1679ES—1 J.S. Rev. 6-04 Impreso en Mèxico Honeywell Limited-Honeywell Limitée 35, Dynamic Drive Scarborough, Ontario M1V 4Z9 www.honeywell.