T8775A,C The Digital Round™ Non-Programmable Thermostats OWNER’S GUIDE ® U.S. Registered Trademark Patents Pending © 2004 Honeywell International Inc.
(T8775C ONLY) SELECTS ON/AUTO (T8775C ONLY) SELECTS COOL/OFF/HEAT ROOM SET SHOWS THAT THE CURRENT ROOM TEMPERATURE IS DISPLAYED. SHOWS THAT THE CURRENT TEMPERATURE SETTING IS DISPLAYED. DISPLAYS ROOM OR SET TEMPERATURE DISPLAYS AND ADJUSTS TEMPERATURE SETTING/TURNS BACKLIGHT ON M19470 Fig. 1. T8775 Thermostat (features and operation).
Setting SYSTEM and FAN Switches (T8775C only) ❑ System and Fan settings are controlled by using SYSTEM and FAN switches located on the top of the thermostat (see Fig. 1). IMPORTANT Do not operate the T8775C in cooling mode when the outdoor temperature is below 50°F (10°C), or damage to compressor could result. SET THE SYSTEM SWITCH: ❑ Heat: The thermostat controls your heating system. ❑ Off: Both heating and cooling systems are off. ❑ Cool: The thermostat controls your cooling system.
Backlit Display ❑ The backlight can be turned on by turning the dial, or by pushing the backlight button as shown in Fig. 1. Display Temperature Setting NOTE: Your temperature setting can be set anywhere from 40°F to 90°F (4°C to 32°C) in heating and 45°F to 99°F (7°C to 37°C) in cooling (T8775C only). ❑ Turn the dial one click to display the current temperature setting. A indicator points to Set when the temperature setting is displayed.
Adjust Temperature Setting ❑ To lower the temperature setting, turn the dial counterclockwise. ❑ To raise the temperature setting, turn the dial clockwise. Troubleshooting Guide CAUTION Equipment Damage Hazard. Can cause permanent damage to compressor or other equipment. Do not operate cooling when outside temperature is below 50°F (10°C). Allow compressor to remain off for five minutes before restarting. See equipment manufacturer instructions. Heating or cooling does not come on.
❑ In heating, make sure the temperature setting is above the room temperature and the flame is present in the display. ❑ In cooling, make sure the temperature setting is below the room temperature and a solid snowflake is present in the display (T8775C only). NOTE: If a call for cooling is made before the compressor has been off for five minutes, or if a power interruption occurs while the compressor is running, the thermostat will go into a five-minute delay to protect the compressor.
69-1679EF—1
Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 69-1679EF—1 J.S. Rev. 6-04 Printed in Mexico Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 www.honeywell.
Thermostats ronds numèriques, non programmables The Digital Round™ T8775A,C GUIDE DU PROPRIÈTAIRE ® Marque de commerce déposée aux É.-U. • Brevets en instance © 2004 Honeywell International Inc.
(T8775C SEULEMENT) SÉLECTION DE ON OU AUTO (T8775C SEULEMENT) SÉLECTION DE COOL, OFF OU HEAT ROOM SET INDIQUE QUE LA TEMPÉRATURE AMBIANTE ACTUELLE EST AFFICHÉE. INDIQUE QUE LE POINT DE CONSIGNE ACTUEL DE LA TEMPÉRATURE EST AFFICHÉ. AFFICHAGE DE LA TEMPÉRATURE AMBIANTE OU DU POINT DE CONSIGNE AFFICHAGE ET RÉGLAGE DU POINT DE CONSIGNE OU RÉTROÉCLAIRAGE MF19470 Fig. 1. Thermostat T8775 (caractéristiques et fonctionnement).
Réglage des sélecteurs du système et du ventilateur (T8775C seulement) Le réglage du fonctionnement du système et du ventilateur se fait manuellement à l'aide des sélecteurs situés dans la partie supérieure du thermostat. (Voir la Fig. 1.) IMPORTANT Ne pas faire fonctionner le thermostat T8775C lorsque le système est en mode refroidissement si la température extérieure est inférieure à 10 °C (50 °F). Cela pourrait endommager le compresseur.
Réglage du sélecteur du ventilateur • • Auto : Réglage normal pour la plupart des maisons. Le ventilateur fonctionne seulement lorsque le système de chauffage ou de refroidissement est en marche. On : Le ventilateur fonctionne de façon continue. Ce réglage assure une meilleure circulation de l'air. Fonctionnement du thermostat REMARQUE : Aucune pile n'est nécessaire car le point de consigne de la température est mémorisé en permanence.
Affichage du réglage de la température REMARQUE : En mode chauffage, le point de consigne peut être réglé entre 4 °C et 32 °C (40 °F et 90 °F) et en mode refroidissement, il peut être réglé entre 7°C et 37 °C (45 °F et 99 °F) (modèle T8775C seulement). ❑ Tourner le cadran jusqu'au premier clic pour afficher le réglage de la température actuelle. Une flèche pointe vers SET lorsque le réglage de la température est affiché.
Modification du réglage de la température ❑ Pour abaisser la température, tourner le cadran dans le sens antihoraire. ❑ Pour augmenter la température, tourner le cadran dans le sens horaire. Guide de dépannage MISE EN GARDE Risque de dommages matériels Peut causer des dommages irrémédiables au compresseur ou au matériel. Ne pas faire fonctionner le système en mode refroidissement si la température extérieure est inférieure à 10 °C (50 °F). Attendre cinq minutes avant de remettre en marche le compresseur.
Le système de chauffage ou de refroidissement ne se met pas en marche. • • • S'assurer que le sélecteur du système sur le thermostat est réglé à Heat ou à Cool (T8775C seulement). En mode chauffage, vérifier si le point de consigne est réglé à une température supérieure à la température ambiante et si une flamme est affichée. En mode refroidissement, vérifier si le point de consigne est réglé à une température inférieure à la température ambiante et si un flocon de neige est affiché (T8775C seulement).
• • Vérifier les fusibles ou le disjoncteur du système. Remplacer les fusibles ou réenclencher le disjoncteur au besoin. Vérifier la circulation de l'air au niveau du registre. Pour tout renseignement concernant le présent thermostat, veuillez communiquer avec les Services à la clientèle de Honeywell au 1 800 468-1502. Solutions de régulation et d'automatisation Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 69-1679EF—1 J.S. Rév.