User Guide

ManualsBrandsHoneywell ManualsWeather RadioTC150

19 20

1817

RAINFALL HISTORY

The rainfall history records will be automatically stored in

the memory of the main unit. There are three historical

records may be displayed – for the past hour, past day and

past week.

To display any of available rainfall history reading, use any

button on the front panel except the ALARM button. The

display sequence is: LAST HOUR, LAST 24 HOURS, and

LAST 7 DAYS.

To clear the memory, press and hold MEMORY button on t

he front panel for two seconds and all previously stored

readings will be erased (all the historical records will

display a default reading 0.00).

MAXIMUM AND MINIMUM TEMPERATURE

The maximum and minimum record of the indoor and

remote temperatures will be automatically stored in the

memory of the main unit.

To display the minimum, maximum or the current reading

press MEMORY button on the back panel.

To clear the memory, press and hold MEMORY button on

the back for two seconds and all previously stored readings

will be erased.

LOST COMMUNICATION

• If the main unit display line for the remote temperature

 sensor reading goes blank, press and hold the back

 DOWN ( ) button for 2 seconds to begin a new signal

 search. If the signal still isn’t received, please make sure

 that:

• The remote temperature sensor is in its proper location.

• The distance between main unit and remote temperature

 sensor is not over 100 feet (30meters).

ALARMS

HIGH RAIN ALARM

The high rain alarm for the past 24 hours can be set and

displayed at any time by pressing ALARM button on the

front panel.

To set the high rain alarm,

• Press the ALARM button on the front panel until the

 “ALARM HI” will appear on the upper right corner of

 the rainfall information line.

• Press and hold the ALARM button for 2 seconds or until

 the rainfall data digits will flash.

• Enter the rainfall amount you want to set the rain alarm

 for using the front panel UP ( ) or DOWN ( ).

• Press the ALARM button again to confirm and the high

 rain alarm will be set.

NOTE: Press and hold the MODE button on the front panel

to display the rainfall reading in inches or mm.

TIME ALARMS

The Wireless Rain Gauge has three available time alarms –

Weekday alarm ( ), Single alarm( ) and Ice Warning

Alarm (Pre-Al).

• If Weekday alarm is activated, it will sound at the set time

 and the alarm icon will flash Mondays through Fridays.

• If Single day alarm is activated, it will sound at the set

 time and the alarm icon will flash only for this specific

 day and will not activate on subsequent days.

• If Ice Warning Alarm is activated, in will sound at the set

 time and alarm icon will flash if the remote temperature

 for Channel One (1) will reach 35.6°F(+2°C) and below.

NOTE: Ice Warning Alarm can be set only if one or both

of the Weekday or Single alarm are programmed.

• The path between units is clear of obstacles. Shorten the

 distance if necessary.

• Fresh batteries are installed correctly in both remote

 temperature sensor and main unit.

• If there is no reception, please perform the following steps:

• Bring the main unit and remote temperature sensor close

 together.

• Remove four (4) small screws from the back of the remote

 temperature sensor with small Phillips screwdriver, and

 open the battery compartment.

• Remove the batteries from the battery compartment and

 reinstall them in the same manner. Remote sensor LED

 indicator will flash showing transmission of the signal.

• Remove the batteries from the main unit and reinstall

 them in the same manner.

• The remote temperature appeared on the main unit’s

 display will show that transmission is being received

 successfully.

• If the main unit display line for the remote rain gauge

 reading goes blank, press and hold the front DOWN

 ( ) button for 2 seconds to begin a new signal search.

• If the signal still isn’t received, please make sure that:

• The remote rain gauge is in its proper location.

• The distance between main unit and remote rain gauge is

 not over 100 feet (30meters).

• The path between units is clear of obstacles. Shorten the

 distance if necessary.

• Fresh batteries are installed correctly in both remote rain

 gauge and main unit.

TRANSMISSION COLLISION

Signals from the other household devices such as wireless

doorbells, home security systems, and entry control, may

interfere with this product or cause temporary reception

interruption. This is normal and will not affect the general

performance of the product. The transmission and reception

of the remote readings will resume once the interference

subsides.

CALENDAR AND CLOCK DISPLAY MODES

Date is displayed in month-date or date-month format. Each

press of the MODE button on the back panel will toggle the

clock modes between the time with seconds, time with the

day, time zone and a calendar.

MANUAL SETTINGS

CLOCK

• Press and hold MODE button for 3 seconds: the language

 letters will flash.

• Press UP ( ) or DOWN ( ) to change flashing letters.

• After the first value is set, press MODE button again to

 move to the next value

• Continue setting temperature in Celsius or Fahrenheit,

 year, month, date, calendar format, 12 or 24 hour time

 format, hour and minutes.

• Press MODE for the last time to return to the default

 mode (time of day with seconds) after the last parameter

 is set.

TIME ZONE

• Select Time Zone setting mode by pressing MODE button

 until the word “ZONE” will appear to the left of time display

• Press and hold MODE button until flashing“0:00” digits

 will appear prompting to set the desired time zone in

 30 minutes intervals