Home User guide evohome Security
INDEX Introduction 3 Controlling your system 4 Contactless tag reader (SPR-S8EZS) 4 Wireless remote control key fob (TCC800MS) 7 Wireless panic button (TCPA1BS) 8 Honeywell Total Connect Comfort International iOS/Android app 9 evohome Security hub LED indications 10 Types of alerts and alarms generated 11 Battery maintenance 12 Troubleshooting 12
INTRODUCTION This document is intended to help you with the operation of your evohome hub based security system following the installation procedure as described in the online “Installation Guide”. The evohome security system is an alarm system that can be accessed and controlled locally or remotely. A contactless tag reader (SPR-S8EZS), wireless remote control key fob (TCC800MS) or wireless panic button (TCPA1BS) are used for the local operation.
CONTROLLING YOUR SYSTEM Your evohome security system can be controlled via the following interfaces listed below: Note there is no ability to control the system via your Total Comfort Connect (TCC) security web account • Contactless tag reader (SPR-S8EZ) • Wireless Remote control key fob (TCC800MS) • Wireless Panic button (TCPA1BS) • iOS/Android “Honeywell Total Connect Comfort International” app Contactless tag reader (SPR-S8EZ) The tag reader is an accessory typically installed near the entry/exit poi
CONTROLLING YOUR SYSTEM How to use the tag reader The security system can be set in two different arming modes: • Total arm / total set: this mode is used when you leave your premises. • Partial arm / partial set: this mode is used when you want to use your system while in your home (at night for example). Only all sensors that you have set to “Partial mode” in your TCC security web account) As well as arming the tag reader can also be used to initiate a silent SOS/panic (personal attack) alert.
CONTROLLING YOUR SYSTEM To disarm the system when in total arm mode After entering the home whilst armed via the protected door, the system will being a 30 second entry delay and the green LED light shown below in step1 will flash fast during this period. If not disarmed within 30 seconds then an intruder alarm will be triggered. 1. The green light will flash fast after the door is opened during the 30 second entry delay. Beeping sound will also be produced during this period.
CONTROLLING YOUR SYSTEM The tag reader LED lights Set/Unset status (green): Fast flashing during the entry/exit delay Slow flashing when the system is in partial arm mode Off when the system is unset and after the exit delay Faults status (red): On when a fault is present (detailed on the webserver) Slow flashing in case of tag reader low battery Off in normal situation Intrusion status (orange): On when an intruder alarm occurred when the system was set This will be reset at the next set action Technical
CONTROLLING YOUR SYSTEM Security status button This button used to indicate on the remote control key fob, the current security status of the evohome security hub Press and hold the button for 3 seconds. The 3 LEDs on the key fob will toggle and the one corresponding to the current security status will remain lit for 3 seconds Wireless Panic button (TCPA1BS) The panic button is used to trigger a SOS/panic (personal attack) alert immediately in the event of an emergency.
CONTROLLING YOUR SYSTEM “Honeywell Total Connect Comfort International” iOS/Android app The “Honeywell Total Connect Comfort International” app allows you also control and view your evohome security hub system from the comfort of your smartphone or tablet remotely whilst away from home. Ensure that your iOS/Android device is connected to the internet via wifi or mobile network before using this app.
EVOHOME SECURITY HUB LED INDICATIONS The evohome security hub has three lights as shown below. Light 2 Light 1 Light 3 Light 1: Indication on the power supply state of the hub • Green fixed: the hub is correctly powered • Orange blinking: the hub is on battery power only. Light 2: Indication of the arming state of the system • Off: The system is disarmed • Green fixed: the system is in “Total arm” • Green blinking: the system is in “Partial arm” • Orange blinking: an intrusion was detected.
TYPES OF ALARMS AND ALERT GENERATED The evohome security hub generates the following types of alarms. Up to 3 registered contacts will receive an alert via email/SMS provided they have been setup within your TCC security account during installation of your system. Intruder alarm: Sounds for 180 seconds An intruder alarm is triggered by any of the following sensors and can be stopped if disarmed by end user via the contactless tag reader SPR-S8EZS, remote control key fob TCC800MS or the iOS/Android app.
BATTERY MAINTENANCE When battery is low in one accessory, the main contact will receive an email/SMS notification informing to change batteries. This notification does not mention that specific accessory. It is recommended to replace the batteries in ALL accessories given the battery life in most of the accessories are similar (Approximately 4-5 years). Refer to the installation guide supplied with the accessory for details on replacing the battery for that accessory.
TROUBLE SHOOTING 5. The system does not alarm or send any alert to any contacts after the protected door window sensor or motion sensor is triggered when armed. Ensure that the sensor is installed within operating range of the evohome security hub. If too far then locate closer to the hub Ensure that the sensors and all siren accessories are correctly registered to your system.
Honeywell Novar ED&S Ltd The Arnold Centre, Paycocke Road Basildon, Essex, SS14 3EA England getconnected.honeywell.com 32320213-001 Rev.A © 2016 Honeywell International Inc.