Wireless Indoor/Outdoor Thermometer with US Atomic Clock Introduction Thank you for selecting the Honeywell Wireless Indoor/ Outdoor Thermometer with US Atomic Clock. This device includes precise time keeping, alarms and indoor/outdoor temperature monitoring features that you can enjoy from the comfort of your home. In this package you will find: • Main unit (receiver) • Remote sensor (transmitter) TS13 Please keep this manual handy as you use your new item.
A FOUR-LINE DISPLAY Allows easy reading of the indoor or outdoor temperature and calendar clock B CHANNEL SELECTOR Selects different remote sensor readings C MEMORY [MEM] BUTTON Recalls maximum or minimum temperature D MODE BUTTON Changes display modes and confirms setting E ALARM ON/OFF BUTTON Selects an alarm time and sets an alarm status F SNOOZE/LIGHT BUTTON Activates the snooze and LCD backlight G WALL-MOUNT RECESSED HOLE Keeps the main unit on a wall H UP ( ) BUTTON Increases the setting FEATURES MAI
REMOTE TEMPERATURE SENSOR * Remote temperature transmission to the main unit via 433MHz signal.
BATTERY INSTALLATION MAIN UNIT The Wireless Indoor/Outdoor Thermometer main unit uses 2 “AA” batteries (not included). When the LCD becomes dim or the respective low battery indicator shows up on the indoor or remote temperature display, the battery replacement is required. To install or replace the batteries, please follow these steps: 1. Remove the battery compartment door on the back of the main unit. 2. Insert 2 “AA” size batteries (not included) matching the polarities shown. 3.
Use the ALARM ON/OFF button: * To view the weekday alarm, single alarm or the pre-alarm. * To set the alarm times. * To turn off any alarm. CALENDAR CLOCK DISPLAY MODES Both an alarm time and the calendar share the same section of the LCD display. The next line displays the current time with seconds and the day of the week. The calendar is displayed in the month and day format. If the alarm time is displayed, press MODE to display the calendar in month-day format.
* Pre-Alarm If the remote temperature (channel 1) is 32˚F or below, the pre-alarm feature will be activated. The pre-alarm time interval can be set for 15, 30, 45, 60, 75 or 90 minutes before the weekday or single alarm time. This alarm will only sound if either the weekday or single alarms are armed. It may warn you about the lower temperature weather conditions and wake you up earlier in case of a potential ice or snow. This alarm can be bypassed during the set up if you choose not to use it.
DISABLING ATOMIC TIME SIGNAL RECEPTION The main unit can be set manually to disable the daily reception of the WWVB time signal. Press and hold the and buttons at the same time for 3 seconds and the radio reception icon will disappear. To enable WWVB receiver, press and hold the and buttons at the same time for 3 seconds again. The radio reception icon will flash. The main unit will start to search for the WWVB time signal immediately.
TEMPERATURE TREND The trend indicator shows the trend of temperatures collected at a particular remote sight. There are three trends will be shown: Rising, Steady, and Falling. Arrow Indicator Temperature Rising Steady Falling MAXIMUM AND MINIMUM TEMPERATURE The maximum and minimum records of the indoor and remote temperature will be automatically stored in the memory. The main unit will display the minimum, maximum and the current reading upon each press of the MEM button.
CARE OF YOUR WIRELESS INDOOR/OUTDOOR THERMOMETER WITH US ATOMIC CLOCK This product is engineered to give you years of satisfactory service if you handle it carefully. Here are a few precautions: 1. Do not immerse the units in water. 2. Do not use any corrosive cleanser or chemical solution on the units. They may scratch the plastic parts and corrode the electronic circuit. 3.
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. DECLARATION OF CONFORMITY Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.hidekielectronics.us. Click Online Product Registration under the Customer Service menu.