System Installation Guide RedLINK™ Wireless System With Equipment Interface Module Français : voir la page 21 • Español: vea la página 41 Wireless control for up to 3 Heat/2 Cool heat pump systems or up to 2 Heat/2 Cool conventional systems. Installation guide for: • • • • • Wireless equipment interface module FocusPRO® wireless thermostats Wireless remote control Wireless outdoor air sensor Return air sensor DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical shock or equipment damage.
RedLINK TM Installation Guide (EIM) System installation at a glance The THM5320R equipment interface module (EIM) provides control of all heating and cooling equipment from any FocusPRO wireless thermostat. Thermostat Optional outdoor air sensor HVAC equipment Remote control EIM M28484 Installation procedure 1 2 3 4 5 6 Mount and wire EIM................................................................... Pages 3-4 Install batteries in wireless devices................................................
Français : voir la page 21 • Español: vea la página 41 1 Mount and wire EIM Mount EIM on wall near HVAC equipment, or on the equipment itself. Do not install inside HVAC equipment. Use screws & anchors as appropriate for mounting surface. Install return air sensor (optional)** Install EIM The return air sensor maintains safe indoor temperature (62° F in Heat, 82° F in Cool) if thermostat power is lost. THM5320 R POWER HEAT COOL FAN Drill 1/4” hole (6.
RedLINK TM Installation Guide (EIM) EIM wiring guide FURNACE See detailed wiring guides for specific system types on pages 16-17.
Français : voir la page 21 • Español: vea la página 41 2 Install batteries in wireless devices When system wiring is complete, install batteries in all devices. Make sure batteries are inserted properly (see polarity marks on illustrations below).
RedLINK TM Installation Guide (EIM) Link thermostat to wireless network Zone number Wireless Setup 0 0 Press NEXT (always leave zone number set to zero). Zone numbers 1-4 are for use with TrueZONE panels only. Next M28477 Zone name Wireless Setup 36 Back 52 Press NEXT (or see page 11 to change the zone name if needed). Change zone name only if you have more than one thermostat and EIM. Next M28478 Wireless Setup Press CONNECT to establish a link to the wireless network.
Français : voir la page 21 • Español: vea la página 41 Link remote control to wireless network (optional) CONNECT WIRELESS SETUP M28481 Press to link another EIM 1 Make sure the Connected light on the EIM is flashing (see page 5). 2 Press CONNECT at the remote. There will be a short delay as the remote seeks a signal from the wireless network. 3 When the screen displays "Connected," press DONE. 4 Press NO at the next screen to save and exit. (Or press YES and repeat steps 1-4 to link another EIM.
RedLINK TM Installation Guide (EIM) 4 Exit wireless setup Press CONNECT at the EIM to exit wireless setup (light should stop flashing). Note: The EIM will automatically exit wireless setup after 15 minutes of inactivity. Note: If installing more than one thermostat and EIM, you must exit wireless setup before installing an additional thermostat and EIM. 5 Customize thermostat (installer setup) Follow the steps below to begin installer setup.
Français : voir la page 21 • Español: vea la página 41 Installer setup tables Setup function Settings & options (factory default in bold) 0 Zone number 0 No zoning (single thermostat used with THM5320R EIM) [Options: select zone 1, 2, 3 or 4] 1 System type 0 1 2 3 4 5 6 7 8 9 10 1 heat/1 cool conventional 1 heat/1 cool heat pump (no aux.
RedLINK TM Installation Guide (EIM) Installer setup tables Setup function Settings & options (factory default in bold) 15 Compressor off time 5 (minimum) 16 Schedule format 5 minutes (Heat On/Cool On flashes during off time) [Options: 0 to 4 minutes] Applies only to Model TH6320 0 Weekday/weekend program schedule 1 Weekday/Saturday/Sunday program schedule 17 External fossil fuel kit 1 0 External fossil fuel kit controls backup heat Thermostat controls backup heat (outdoor sensor required) 18 Dual fu
Français : voir la page 21 • Español: vea la página 41 Installer setup tables Setup function Settings & options (factory default in bold) 36 Zone name 52 Thermostat 1 Basement 2 Bathroom 3 Bathroom 1 4 Bathroom 2 5 Bathroom 3 6 Bedroom 7 Bedroom 1 8 Bedroom 2 9 Bedroom 3 10 Bedroom 4 11 Boat House 12 Bonus Room 13 Computer Room 14 Den 15 Dining Room 16 Exercise Room 17 Family Room 18 Fireplace 19 Foyer 20 Game Room 21 Garage 22 Great Room 23 Guest Room 24 Gym 25 Kid's Room 26 Kitchen 27 Kitchen 1 28
RedLINK TM Installation Guide (EIM) System test Follow the procedure below to test for proper operation. System test number 02 Done Back System status 0 Next M28489 M28488 Press s or t to check system status To begin, press and hold the s and t buttons until the display changes (about 3 seconds).
Français : voir la page 21 • Español: vea la página 41 6 Mount thermostat & outdoor sensor 3/16" holes for drywall 7/32" holes for plaster Mounting screw Wall anchor Detach wallplate Wallplate M28490 Outdoor sensor (optional) Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight. Place sensor securely in bracket, facing away from wall.
RedLINK TM Installation Guide (EIM) EIM status lights When installation is complete, check the status lights on the equipment interface module to verify proper operation. System status lights • Power: EIM is working properly. • Heat: Heating system is on. • Cool: Cooling system is on. • Fan: Fan is on. Note: If connected light is flashing, press CONNECT button to turn off flashing light, then recheck status lights.
Français : voir la page 21 • Español: vea la página 41 Replacing system components Thermostat To replace a thermostat, install batteries and follow the procedures on pages 5-6 to link it to the wireless network. If necessary, modify settings as needed (see tables on pages 9-11). Remote control & outdoor sensor To replace a remote control or outdoor air sensor, install batteries and follow the procedures on pages 5-7 to link it to the wireless network.
RedLINK TM Installation Guide (EIM) System-specific wiring guides Conventional systems See [notes] on next page.
Français : voir la page 21 • Español: vea la página 41 System-specific wiring guides Heat pump systems See [notes] below.
RedLINK TM Installation Guide (EIM) Specifications & replacement parts Operating Ambient Temperature Thermostat: 32 to 120° F (0 to 48.9° C) Remote control: 32 to 120° F (0 to 48.9° C) EIM: -40 to 165° F (-40 to 73.9° C) Outdoor air sensor: -40 to 140° F (-40 to 60° C) Return air sensor: 0 to 200° F (-17.8 to 93.
Français : voir la page 21 • Español: vea la página 41 Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.
Need Help? For assistance with this product please visit http://customer.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® U.S. Registered Trademark. © 2011 Honeywell International Inc. 69-2091EFS—07 M.S. Rev. 03-11 Printed in U.S.A.
Guide d’installation du système Système sans fil RedLINK MC Avec module d’interface Français : voir la page 21 • Español: vea la página 41 Commande sans fil pour thermopompes offrant jusqu’à 3 étages de chauffage et 2 étages de refroidissement ou pour systèmes classiques offrant jusqu’à 2 étages de chauffage et 2 étages de refroidissement Guide d’installation pour : • • • • • Module d’interface sans fil Thermostat sans fil FocusPRO® Télécommande sans fil Capteur d’air extérieur sans fil Capteur d’air
Guide d’installation du système Installation du système en un coup d’oeil Le module d’interface avec le matériel (MIM) THM5320R assure la commande de tout le matériel de chauffage et de refroidissement à partir de tout thermostat sans fil FocusPRO. Thermostat Capteur d’air extérieur Matériel de CVCA Télécommande MIM MF28484 Installation 1 2 3 4 5 6 Installation et raccordement du MIM.................................... Pages 23-24 Insertion des piles dans l’appareil sans fil.............................
English: see page 1 • Español: vea la página 41 1 Installation et raccordement du MIM Installer le MIM sur le mur à proximité du système de CVCA ou sur le système même. Ne pas l’installer à l’intérieur du système. Utiliser les vis et les chevilles d’ancrage fournies pour une installation en surface.
Guide d’installation du système Guide de raccordement du MIM APPAREIL DE CHAUFFAGE Voir les schémas de raccordement détaillés en fonction du type de système aux pages 36-37. SYSTÈMES CLASSIQUES Transformateur 24 V c.a. 120 V c.a.
English: see page 1 • Español: vea la página 41 2 Insertion des piles dans l’appareil sans fil Lorsque le raccordement du système est terminé, insérer des piles dans tous les appareils. S’assurer que les piles sont correctement insérées (voir les marques de polarité sur l’illustration).
Guide d’installation du système Relier le thermostat au réseau sans fil Numéro de zone Wireless Setup 0 0 Appuyer sur NEXT (toujours laisser le numéro de zone à zéro). Les zones 1 à 4 sont utilisées avec des tableaux TrueZone seulement. Next M28477 Nom de zone Wireless Setup 36 Back 52 Appuyer sur NEXT (ou voir la page 31 pour modifier le nom de zone au besoin). Modifier le nom de zone seulement s’il y a plus d’un thermostat et d’un MIM.
English: see page 1 • Español: vea la página 41 Relier la télécommande au réseau sans fil (optionnel) CONNECT WIRELESS SETUP M28481 Appuyer pour Appuyer pour relier enregistrer et un autre MIM quitter 1 S’assurer que le voyant «Connected» du MIM clignote (voir la page 25). 2 Appuyer sur CONNECT de la télécommande. Il y a aura un court délai pendant que la télécommande recherche le signal du réseau sans fil. 3 Lorsque l’écran affiche «Connected», appuyer DONE.
Guide d’installation du système 4 Quitter la configuration du réseau sans fil Appuyer sur CONNECT au MIM pour quitter la configuration du réseau sans fil (le voyant devrait cesser de clignoter). Remarque : Le MIM quittera automatiquement la configuration du réseau sans fil après 15 minutes d’activité. Remarque : Lors de l’installation de plus d’un thermostat et plus d’un MIM, il faut quitter la configuration du réseau sans fil avant l’installation d’un thermostat et d’un MIM additionnels.
English: see page 1 • Español: vea la página 41 Tableaux de configuration par l’installateur Fonctions Options (réglages de l’usine en gras) 0 Numéro de zone 0 Pas de zonage (un seul thermostat employé avec le MIM THM5320R) [Options : sélectionner la zone 1, 2, 3 ou 4] 1 Type de système 0 1 2 3 4 5 6 7 8 9 10 Chauffage-refroidissement classique 1 chaud/1 froid Thermopompe 1 chaud/1 froid (sans chauffage auxiliaire) Chauffage seulement (y compris Série 20) Chauffage seulement avec ventilateur Ref
Guide d’installation du système Tableaux de configuration par l’installateur Fonctions Options (réglages de l’usine en gras) 5 minutes (les mots «Heat On/Cool On» clignotent à l’écran) [Options : 0 à 4 minutes] 15 Temps d’arrêt du compresseur (min.
English: see page 1 • Español: vea la página 41 Tableaux de configuration par l’installateur Fonctions 36 Nom de la zone Options (réglages de l’usine en gras) 52 Thermostat 1 Basement 2 Bathroom 3 Bathroom 1 4 Bathroom 2 5 Bathroom 3 6 Bedroom 7 Bedroom 1 8 Bedroom 2 9 Bedroom 3 10 Bedroom 4 11 Boat House 12 Bonus Room 13 Computer Room 14 Den 15 Dining Room 16 Exercise Room 17 Family Room 18 Fireplace 19 Foyer 20 Game Room 21 Garage 22 Great Room 23 Guest Room 24 Gym 25 Kid's Room 26 Kitchen 27 Kitch
Guide d’installation du système Test du système Suivre les étapes ci-dessous pour vérifier le bon fonctionnement du système. Numéro de test du système État du système 02 Done Back 0 Next M28489 M28488 Appuyer sur les boutons s et t jusqu’à ce que l’affichage change (au bout d’environ 3 secondes).
English: see page 1 • Español: vea la página 41 6 Installer le thermostat et le capteur extérieur 3/16 po si le mur est en placoplâtre 7/32 po si le mur est en plâtre Vis de fixation Cheville d’ancrage Détacher la plaque murale Plaque murale M28490 Capteur extérieur (optionnel) Installer le capteur sur un mur extérieur à la verticale, à au moins 6 pouces (15 cm) de tout surplomb. Choisir un emplacement où le capteur sera à l’abri des rayons du soleil.
Guide d’installation du système Voyants d’état du MIM Une fois l’installation terminée, vérifier les voyants d’état du module d’interface pour s’assurer de son bon fonctionnement. Voyants d’état du système • Power : MIM fonctionne correctement. • Heat : Chauffage est en marche. • Cool : Refroidissement est en marche. • Fan : Ventilateur est en marche. Remarque : Si le voyant «Connected» clignote, appuyer sur CONNECT pour éteindre le voyant clignotant, puis vérifier à nouveau les voyants d’état.
English: see page 1 • Español: vea la página 41 Remplacement des composants du système Thermostat Pour remplacer un thermostat, insérer des piles neuves et suivre les étapes décrites à la page 25 pour le relier au réseau sans fil. Au besoin, modifier les paramètres (voir les tableaux aux pages 29 à 31). Télécommande et capteur extérieur Pour remplacer une télécommande ou un capteur d’air extérieur, insérer des piles neuves et suivre les étapes décrites aux pages 25-27 pour le relier au réseau sans fil.
Guide d’installation du système Guides de raccordement en fonction du système Systèmes classiques Voir [notes] à la page suivante Système 1C/1F (1 transformateur) C R Rc Rh W Y G Système de refroidissement seulement [5] Commun 24 V c.a. Alimentation [1] [R+Rc+Rh réunis par un cavalier] [R+Rc+Rh réunis par un cavalier] Relais de chauffage Contacteur du compresseur Relais de ventilateur C R Rc Rh Y G Système 1C/1F (2 transformateurs) Chauffage seulement [3] C R Rc Rh W C R Rc Rh W Y G Commun 24 V c.
English: see page 1 • Español: vea la página 41 Guides de raccordement en fonction du système Voir [notes] ci-dessous Thermopompes Thermopompe 1C/1F [8] C R Rc Rh O/B Y G Thermopompe 2C/2F [10] Commun 24 V c.a. Alimentation [1] [R+Rc+Rh réunis par un cavalier] [R+Rc+Rh réunis par un cavalier] Vanne d’inversion [7] Contacteur du compresseur Relais de ventilateur C R Rc Rh O/B Y Y2 G Thermopompe 2C/1F [9] C R Rc Rh O/B Aux Y G L Commun 24 V c.a.
Guide d’installation du système Caractéristiques techniques et pièces de rechange Gamme de température ambiante de service Thermostat : 0 à 48,9 °C (32 à 120 °F) Télécommande : 0 à 48,9 °C (32 à 120 °F) MIM : -40 à 73,9 °C (-40 à 165 °F) Capteur d’air extérieur : -40 à 60 °C (-40 à 140 °F) Capteur d’air repris : -17,8 à 93,3 °C (0 to 200 °F) Humidité relative de service Thermostat : 5 % à 90 % (sans condensation) Télécommande : 5 % à 90 % (sans condensation) MIM : 5 % à 95 % (sans condensation) Capteur d
English: see page 1 • Español: vea la página 41 Information sur la réglementation Déclaration de conformité à la FCC (partie 15,19) (États-Unis seulement) Cet appareil est conforme à la Partie 15 des règles de la FCC. Le fonctionnement de ce système est assorti aux deux conditions suivantes : 1 L’appareil ne peut causer d’interférences nuisibles, et 2 L’appareil doit accepter les interférences reçues, y compris celles qui pourraient nuire à son fonctionnement.
Besoin d’aide? Pour obtenir de l’aide sur ce produit Honeywell, consulter le site http://customer.honeywell.com ou s’adresser aux Services à la clientèle de Honeywell en composant sans frais le 1-800-468-1502 Solutions de régulation et d’automatisation Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® Marque de commerce déposée aux É.-U.
Guía de instalación del sistema Sistema inalámbrico RedLINK TM Con módulo de interfaz del equipo English: see page 1 • Français : voir la page 21 Control inalámbrico para sistemas de bomba de calor de hasta 3 calentadores/2 refrigeradores o sistemas convencionales de hasta 2 calentadores/2 refrigeradores.
Guía de instalación del sistema Instalación rápida del sistema El módulo de interfaz del equipo (EIM) THM5320R permite el control de todo el equipo de calefacción y refrigeración desde cualquier termostato inalámbrico FocusPRO. Termostato Sensor de aire exterior Control remoto Equipo de HVAC EIM MS28484 Procedimiento de instalación 1 Instalación y conexión del EIM.............................................. Págs. 43-44 2 Instalación de las baterías en los dispositivos inalámbricos.................
English: see page 1 • Français : voir la page 21 1 Instalación y conexión del EIM Instale el EIM en una pared cerca del equipo de HVAC o sobre el mismo equipo. No lo instale dentro del equipo de HVAC. Utilice tornillos y tarugos de acuerdo con la superficie de montaje. Instalación del sensor de aire de retorno (opcional)** Instalación del EIM El sensor de aire de retorno conserva la temperatura segura en interiores (62° F en calefacción y 82° F en aire acondicionado) si se queda sin electricidad.
Guía de instalación del sistema Guía de cableado del EIM SISTEMA DE CALEFACCIÓN Vea las guías de cableado detalladas para tipos de sistemas específicos en las págs. 56-57.
English: see page 1 • Français : voir la page 21 2 Instalación de las baterías en los dispositivos inalámbricos Una vez finalizado el cableado del sistema, instale las baterías en todos los dispositivos. Asegúrese de colocar las baterías correctamente (vea las marcas de polaridad en las siguientes ilustraciones).
Guía de instalación del sistema Conexión del termostato a la red inalámbrica Número de zona Wireless Setup 0 0 Presione NEXT (siempre deje configurado el número de zona en cero). Los números de zona del 1-4 solo se utilizan con paneles TrueZONE. Next M28477 Nombre de zona Wireless Setup 36 Back 52 Presione NEXT (o vea la pág. 51 para cambiar el nombre de zona si es necesario). Cambie el nombre de zona solo si tiene más de un termostato y EIM.
English: see page 1 • Français : voir la page 21 Conexión del control remoto a la red inalámbrica (opcional) CONNECT WIRELESS SETUP M28481 Presione para conectar otro EIM YES Presione para guardar y salir NO CONNECT MORE? M28482 1 Asegúrese de que la luz de Connected en el EIM esté destellando (vea la pág. 45). 2 Presione CONNECT en el control remoto. Habrá una breve demora mientras el control remoto busca una señal procedente de la red inalámbrica.
Guía de instalación del sistema 4 Salida del modo Wireless Setup Presione CONNECT en el EIM para salir del modo Wireless Setup (la luz debe dejar de destellar). Nota: el EIM saldrá automáticamente del modo Wireless Setup después de 15 minutos de inactividad. Nota: si está instalando más de un termostato y EIM, debe salir del modo Wireless Setup antes de instalar un termostato y EIM adicionales.
English: see page 1 • Français : voir la page 21 Tablas de la configuración de instalación Funciones Opciones (Negrita: las configuraciones predeterminadas) 0 Número de zona 0 Sin zona (se utiliza un solo termostato con el EIM THM5320R) [opciones: seleccione la zona 1, 2, 3 ó 4] 1 Tipo de sistema 0 1 2 3 4 5 6 7 8 9 10 Convencional 1 calentador/1 refrigerador Bomba de calor 1 calentador/1 refrigerador (sin AuxHeat) Calefacción únicamente (incluye la Serie 20) Calefacción únicamente con ventilador
Guía de instalación del sistema Tablas de la configuración de instalación Funciones Opciones (Negrita: las configuraciones predeterminadas) 5 minutos (Heat On/Cool On destella durante el tiempo de apagado) [Opciones: 0 a 4 minutos] 15 Tiempo apagado del compresor (mín.
English: see page 1 • Français : voir la page 21 Tablas de la configuración de instalación Funciones Opciones (Negrita: las configuraciones predeterminadas) 36 Nombre de la zona 52 Thermostat 1 Basement 2 Bathroom 3 Bathroom 1 4 Bathroom 2 5 Bathroom 3 6 Bedroom 7 Bedroom 1 8 Bedroom 2 9 Bedroom 3 10 Bedroom 4 11 Boat House 12 Bonus Room 13 Computer Room 14 Den 15 Dining Room 16 Exercise Room 17 Family Room 18 Fireplace 19 Foyer 20 Game Room 21 Garage 22 Great Room 23 Guest Room 24 Gym 25 Kid's Room
Guía de instalación del sistema Prueba del sistema Siga el procedimiento que se detalla a continuación para verificar el funcionamiento adecuado. Número de la prueba Estado del del sistema sistema 02 Done 0 Back Next M28489 M28488 Presione s o t para verificar el estado del sistema Para comenzar, presione y mantenga presionados los botones s y t hasta que la visualización cambie (3 segundos, aprox.
English: see page 1 • Français : voir la page 21 6 Instalación del termostato y del sensor exterior 3/16” (4,8 mm) para paneles de yeso 7/32” (5,6 mm) para yeso Tornillo de fijación Tarugo de pared Placa de pared desmontable Placa de pared M28490 Sensor exterior (opcional) Instale el sensor en una pared exterior vertical, a 6 pulgadas (15,2 cm) como mínimo, debajo de cualquier alero. Elija una ubicación donde no haya luz solar directa.
Guía de instalación del sistema Luces de estado del EIM Al terminar la instalación, verifique las luces de estado en el módulo de interfaz del equipo para verificar el funcionamiento correcto. Luces de estado del sistema • Power: el EIM funciona correctamente. • Heat: calefacción está encendido. • Cool: refrigeración está encendido. • Fan: ventilador está encendido.
English: see page 1 • Français : voir la page 21 Reemplazo de los componentes del sistema Termostato Para reemplazar un termostato, instale las baterías y siga los procedimientos de las págs. 45 a 46 para conectarlo a la red inalámbrica. Si es preciso, modifique las configuraciones según sea necesario (vea las tablas de las págs. 49 a 51). Control remoto y sensor exterior Para reemplazar el control remoto o el sensor de aire exterior, instale las baterías y siga los procedimientos de las págs.
Guía de instalación del sistema Guías de cableado específicas del sistema Sistemas convencionales Vea [notas] en la pág. siguiente. Sistemas de 1C/1R (1 transformador) C R Rc Rh W Y G Refrigeración únicamente [5] 24 V CA común Energía [1] [R+Rc+Rh unidos por un puente] [R+Rc+Rh unidos por un puente] Relé de la calefacción Interruptor auto.
English: see page 1 • Français : voir la page 21 Guías de cableado específicas del sistema Sistemas de bombas de calor Vea [notas] a continuación. Bomba de calor de 1C/1R [8] C R Rc Rh O/B Y G Bomba de calor de 2C/2R [10] 24 V CA común Energía [1] [R+Rc+Rh unidos por un puente] [R+Rc+Rh unidos por un puente] Válvula de cambio [7] Interruptor auto.
Guía de instalación del sistema Especificaciones y piezas de repuesto Temperatura ambiente de funcionamiento Termostato: 32 a 120° F (0 a 48,9° C) Control remoto: 32 a 120° F (0 a 48,9° C) EIM: -40 a 165° F (-40 a 73,9° C) Sensor de aire exterior: -40 a 140° F (-40 a 60° C) Sensor de aire de retorno: 0 a 200° F (-17,8 a 93,3° C) Humedad relativa de funcionamiento Termostato: 5% a 90% (sin condensación) Control remoto: 5% a 90% (sin condensación) EIM: 5% a 95% (sin condensación) Sensor de aire exterior:
English: see page 1 • Français : voir la page 21 Información reguladora Declaración de conformidad con las regulaciones FCC (Sección 15.19) (solo en los EE. UU.) Este dispositivo cumple con la Sección 15 de las regulaciones FCC. El funcionamiento está sujeto a las dos condiciones siguientes: 1 Este dispositivo no debe causar interferencia perjudicial. 2 Este dispositivo deberá aceptar cualquier interferencia que se reciba, incluso la interferencia que pudiese causar el funcionamiento no deseado.
¿Necesita ayuda? Consulte sobre este producto en http://customer.honeywell.com o llamando sin cargo a atención al cliente de Honeywell 1-800-468-1502 Automatización y control desenlace Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® Marca registrada de los EE. UU. © 2011, Honeywell Internacional Inc. 69-2091EFS—07 M.S. Rev. 03-11 Impreso en EE. UU.