VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
105 68-0312—05
Fig. 283.
4. Touch or to select the Heat and Cool tempera-
tures.
Fig. 284.
5. Review the settings and touch Done to save them.
Touch Cancel to ignore changes.
Setting Holiday Override:
Commercial Use
This feature lets you customize temperature settings to be
maintained from now until a specified date. The thermostat
resumes normal scheduling on the date you select.
1. Touch MENU.
Fig. 285.
2. Select Holiday Mode to display Temperature While
Away.
Fig. 286.
3. Touch or to select the Heat and Cool tempera-
tures, then touch Next to select return date.
Fig. 287.
4. Review the settings and touch Done to save them.
Touch Cancel to ignore the changes.
NOTE: The cool temperature can only be set higher than
the unoccupied program setting and the heat
temperature can only be set lower than the unoc-
cupied program setting.
Initiating Occupancy Mode:
Commercial Use
This feature keeps temperature at an energy saving level
until you touch Press HERE to Start Occupancy. When you
arrive, touch the message to maintain a comfortable
temperature while the room is occupied.
Fig. 288.
Touch the or buttons to set the temperature or the
Hold Until time. The temperature is maintained until the
time you set. Temperature returns to an energy-saving level
after the timer expires, or the “Occupied” period ends.
NOTE: This feature is available only when programmed by
the installer.
MCR34120
Select US holidays
New Year’s Day
MCR34121
Temperature
During Holiday
MCR34100
MCR34122
Holiday Mode
Equipment Status
MCR34123
Temperature
While Away
M34127
Press HERE to
Start Occupancy