VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 112
OPTIONAL ACCESSORIES
PORTABLE COMFORT CONTROL
If you have only one thermostat, you move this remote control
from room to room (like a portable thermostat), to make sure
the temperature is comfortable in the room you’re using. If
you have multiple thermostats, you can view and adjust the
temperature in each room from your armchair. A Portable
Comfort Control can control up to 16 thermostats.
WIRELESS OUTDOOR SENSOR
With a wireless outdoor sensor, your VisionPRO® thermostat
can display outside temperature and humidity. This
information can also be displayed on your handheld Portable
Comfort Control.
WIRELESS INDOOR SENSOR
If an indoor sensor is installed, your VisionPRO thermostat will
respond to temperature and humidity readings at the sensor
location—providing comfort where the sensor is located. With
multiple sensors, the thermostat can average temperature
readings from each, to optimize comfort throughout your
home. The thermostat can be used with up to 6 Wireless
Indoor Sensors.
REDLINK™ INTERNET GATEWAY
The Honeywell RedLINK Internet Gateway gives you remote
access to your VisionPRO® thermostat from the web, smart
phone or tablet. You can view or adjust indoor temperature,
system mode and other settings. The Gateway can also send
alerts to as many as 6 email addresses to notify you if a
problem occurs.
WIRELESS ENTRY/EXIT REMOTE
This device mounts beside your door for one-touch control.
Press AWAY to control to an energy saving temperature when
you leave home. Press HOME to control to a comfortable
temperature when you return. To change pre-set
temperatures, go to MENU > Entry/Exit Remote. Two covers
are sold with the device that allow it to be used in residential or
commercial applications. The Residential cover is labeled
HOME, AWAY and VACATION and the Commercial cover is
labeled OCCUPIED, UNOCCUPIED and HOLIDAY. The
thermostat can be used with up to 3 Entry/Exit remotes. Each
Entry/Exit remote can control up to 16 thermostats.