VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 114
PORTABLE COMFORT CONTROL
The Portable Comfort Control communicates wirelessly
with the thermostat, and can control up to 16 thermostats.
NOTE: Each thermostat can only be connected to
1 Portable Comfort Control.
If you have one thermostat, you move this remote control
from room to room (like a portable thermostat), to make
sure the temperature is comfortable in the room you’re
using. If you have multiple thermostats, you can view and
adjust the temperature in each room from the Portable
Comfort Control.
If you have one thermostat, temperature is measured at the
thermostat (Fig. 302) or Portable Comfort Control (Fig.
303), as you choose.
Fig. 302. Reading temperature at the thermostat.
Fig. 303. Reading temperature at the Portable Comfort
Control.
If the thermostat is being averaged with remote indoor
sensors, and you select THERMOSTAT on the Portable
Comfort Control, you will see the temperature average from
the remote indoor sensors and the thermostat.
NOTE: If the thermostat is not part of the temperature
average, then you will only see the temperature
average from the remote indoor sensors when you
select THERMOSTAT on the Portable Comfort
Control.
If the thermostat is being averaged with remote indoor
sensors, and you select THIS DEVICE on the Portable
Comfort Control, you will see the temperature measured at
the Portable Comfort Control only.
If you have multiple thermostats, temperature is measured
at each thermostat. Press the TOGGLE ZONE arrows to
choose which room to display and adjust. See Fig. 304.
Fig. 304. Portable Comfort Control used with Multiple
Thermostats. Temperature is measured at each
thermostat.