VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 16
3. While the “Connected” light is flashing green on the
EIM, press Next on the thermostat. After a short
delay, the screen will show the thermostat is con-
nected.
Fig. 32.
Fig. 33.
4. Press Next, as directed on screen, to link RedLINK
accessories.
Linking RedLINK Accessories
1. When you see the prompt Connect RedLINK Accesso-
ries?, touch No or Yes.
a. If you select No, continue to step 5.
b. If you select Yes, you will be prompted to Press
Connect on New Accessories. Continue to step 2.
Fig. 34. Connect RedLINK accessories.
NOTE: Accessories must be at least 2 feet away from the
thermostat or EIM during the linking process.
2. While the Press Connect message is displayed (lis-
tening mode), press and quickly release the CON-
NECT button on each new RedLINK accessory.
NOTE: For locations of CONNECT buttons on
RedLINK accessories, see “Locating the
Connect Buttons on RedLINK Accessories”
beginning on page 18.
Fig. 35. Thermostat in listening mode.
3. After a short delay (up to 15 seconds), check thermo-
stat to confirm the connection of each RedLINK
accessory. Touch or to review the list.
Fig. 36. Outdoor sensor added.
4. Touch Done at the thermostat after all new RedLINK
accessories are connected.
NOTE: Thermostat displays a countdown timer while in
the listening mode. If it detects no activity for 15
minutes, it exits listening mode.
Completing Initial Setup
5. Finish the setup by selecting the desired options.
Touch Done after you select the last option you want
to change.
Fig. 37. Thermostat type.
The thermostat now displays its Home screen and the
thermostat setup is complete.
MCR33970
Connect RedLINK
Accessories?
Press Connect on
New Accessories.
MCR33972
Outdoor Sensor
has been added
M34150
THERMOSTAT TYPE
programmable