VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 42
500 Wired Discharge
Sensor
No
Yes
No Both No The thermostat will not display the Wired
Discharge Sensor option if there is no fan in the
system.
501 Indoor Sensor
Name
[Select Indoor Sensor Name]
Indoor Sensor Both No Select a name (location) of the Wired Remote
Indoor Sensor.
502 Indoor Sensor
None
S1
S2
S3
S4
None Both No Select the terminals wired to the Remote Indoor
Sensor.
Number of Sensor Inputs:
Thermostat = S1
Equipment Interface Module = S1, S2, S3 and S4
503 Indoor Sensor Type
10K
20K
10K:
if ISU 101
Application is
Residential
20K:
if ISU 101:
Application is
Commercial
Both No Select 10K or 20K based on the sensor installed.
Refer to resistance values below:
C7189U1005 = 10K ohm
C7772 = 20K ohm
TR21 = 20K ohm
TR21-A = 10K ohm (IMPORTANT - the TR21-A
must be used in combination with a TR21 sensor
or another TR21-A sensor for the thermostat to
calculate the correct indoor temperature reading).
See “Wiring guide — Wired Indoor Sensors”
beginning on page 140 for information on the
sensor type you should select based on how the
sensors are wired. For example, you would select
20K when you have two TR21-A (10K) sensors
wired in series.
504
Use [T-Stat Sensor]
for Temp Ctrl
Use [Remote Indoor
Sensor Name] for
Temp Ctrl
Use [T-Stat Sensor]
in Temp Avg
Use [Remote Indoor
Sensor Name] in
Temp Avg
Use T-Stat Sensor for Temp Ctrl -
Yes or No
Use [Remote Indoor Sensor
Name] for Temp Ctrl - Yes or No
Use T-Stat Sensor in Temp Avg -
Yes or No
Use [Remote Indoor Sensor
Name] in Temp Avg - Yes or No
(Up to 6 Remote Indoor Sensors)
Sensors are
Averaged (T-Stat
Sensor and
Remote)
Both No Select the sensors to be used for temperature
control. If you select more than one, the
thermostat will average the temperature readings
from each sensor.
See “Remote Indoor Sensors” beginning on
page 115.
505 Outdoor Sensor
None
S1
S2
S3
S4
None Both No Select the terminals wired to the Outdoor Sensor.
Number of Sensor Inputs:
Thermostat = S1
Equipment Interface Module = S1, S2, S3 and S4
507 Return Sensor
None
S1
S2
S3
S4
None Both Yes Select the terminals wired to the Return Sensor.
Number of Sensor Inputs:
Thermostat = S1
Equipment Interface Module = S1, S2, S3 and S4
508 Return Sensor Type
10K
20K
10K Both Yes Select 10K or 20K based on the sensor installed.
Refer to resistance values below:
50062329-001 = 10K ohm
32005180-002 = 10K ohm
C7735A1000 = 10K ohm
C7770A = 20K ohm
C7041 = 20K ohm
Table 2. Installer Setup (ISU) Table. (Continued)
ISU
Number
Installer Setup
Name Settings Default
Residential,
Commercial
or Both
Requires
EIM Notes