VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
55 68-0312—05
28 Backlighting
On Demand
Continuous
On Demand Both No Select Continuous or On Demand backlighting.
Select Continuous backlighting if you would like
the backlight to be on all the time (C wire is
required for Continuous backlighting).
Select On Demand backlighting if you would like
the backlight to only turn on after a key press. After
you complete your changes, the screen stays lit for
16 seconds if the thermostat is battery powered
only or it stays lit for 45 seconds if the thermostat
is system powered (C wire).
1400 Clock Format
12 hour
24 hour
12 Both No
1401 Daylight Saving
Time
Off
On
On Both No Set to Off in areas that do not follow Daylight
Saving Time.
1402 Indoor Temperature
Offset
-3° F to 3° F (in 1° F increments)
0° F Both No 0° F - No difference in displayed temperature and
the actual room temperature.
The thermostat displays up to 3°F (1.5°C) lower or
higher than the actual measured temperature.
1402 Indoor Humidity
Offset
-12% to 12% (in 1% increments)
0% Both No 0% - No difference in displayed humidity and the
actual room humidity.
The thermostat displays up to 12% lower or higher
than the actual measured humidity.
1404 Alert Light Indicator
On
Off
On Both No The thermostat has a built in light indicator. When
an alert is active, the light will be on continuous if
the thermostat is powered with 24 VAC (C wire) or
it will flash if the thermostat is powered with
batteries only. The light also turns on when the
system setting is set to Em Heat.
Select On to use the light indicator or select Off to
turn off the light.
1500 Dealer Name
[Dealer Name]
None Both No Dealer information is displayed to the user when
an alert is active and the user can access this
information by selecting "Dealer Information" in
the Menu.
1500 Dealer Phone
[Dealer Phone]
None Both No
1501 Dealer Email
Address
[Dealer Email Address]
None Both No
1501 Dealer Website
[Dealer Website]
None Both No
1502 Dealer Message
[Dealer Message]
None Both No
Table 2. Installer Setup (ISU) Table. (Continued)
ISU
Number
Installer Setup
Name Settings Default
Residential,
Commercial
or Both
Requires
EIM Notes