VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
69 68-0312—05
Temporary Boost: Touch or to select how long to run
ventilation temporarily. To turn it off, set it to zero.
Fig. 131.
Lockout: Touch or to select Yes or No, then touch Next.
Select Yes to prevent ventilation from running during the
Sleep or Unoccupied (commercial) program periods or
when outdoor conditions exceed values set by the installer.
Fig. 132.
Setting Preferences
Preference menu options let you select how the thermostat
displays information or responds to certain situations.
1. Touch MENU and select Preferences.
Fig. 133.
Fig. 134.
2. Select an option and follow prompts:
• Reminders to change filters
• Fahrenheit/Celsius display
• 12/24-hour clock display
• Display Options
–Backlighting (Continuous or On Demand)
–Inactive Backlight (Backlight level while the
screen is not in use. Requires C wire and
Backlighting must be set to Continuous.)
–Screen Contrast
• Alert light options
• Scheduling options
• Adaptive recovery
• Default schedule
• Daylight saving time
Fig. 135.
3. Touch Done to save your settings. Touch Cancel to
ignore changes.
Cleaning the Thermostat Screen
When you select the Clean Screen option, the screen is
locked to prevent accidental changes to the thermostat
while you clean the screen.
1. Touch MENU.
Fig. 136.
2. Select Clean Screen. A prompt asks if you want to
clean the screen for 30 seconds.
Fig. 137.
MCR34136
Run Ventilation For
60 minutes
MCR34137
Lockout in Sleep
Period: No
MCR34100
MCR34170
Preferences
Clean Screen
MCR34139
Reminders
Fahrenheit/Celsius
MCR34100
MCR34140
Clean Screen
Security Settings