VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 94
2. Select the terminals wired to the Ventilator (or Fresh
Air Damper). See Fig. 227.
Fig. 227.
3. Select the Ventilation Control Method. See “Ventila-
tion Control Methods (ISU 1005)” on page 92 for
more information. See Fig. 228.
Fig. 228.
4. Select the Ventilation Fan Control. See “Ventilation
Fan Control (ISU 1006)” on page 93 for more infor-
mation. See Fig. 229.
NOTE: ISU 1006 is only displayed if the Ventilation
Type is ERV / HRV. The thermostat controls
the fan if the Ventilation Type is Fresh Air
Damper.
Fig. 229.
5. If ASHRAE was selected for ISU 1005, select the
Number of Bedrooms and Size of House. See Fig.
230.
Fig. 230.
6. If ASHRAE was selected for ISU 1005, enter the
Equipment Ventilation Rate (CFM). Be sure this set-
ting corresponds with the actual ventilation speed.
This setting determines how often the ventilation
equipment will operate to meet the ASHRAE 62.2
Standard. The thermostat will indicate the following
based on the Equipment Ventilation Rate, Square
Footage and Number of Bedrooms. See Fig. 231.
• Provides an indication if it meets or does not meet
the ASHRAE 62.2 Standard.
• Provides % run time that is needed to meet the
ASHRAE 62.2 Standard.
Fig. 231.
7. Select a Ventilation Priority (see Fig. 232):
c. Lockouts are Priority: The thermostat places a pri-
ority on lockouts versus the ASHRAE 62.2 ventila-
tion standard. The thermostat will not run
ventilation during the following lockout condi-
tions (if configured) unless you manually call for
ventilation:
Scroll to see:
Meets ASHRAE
62.2
Ventilation will run