VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 98
3. Select the reminder you want to set.
4. Press or to set the timer length. Ranges, incre-
ments, and units will change based on the reminder.
NOTE: When set for run time days, the thermostat
tracks the amount of time the fan has run
and compares that time against the number
of run time days selected. Fan run time is
counted when there is a call for forced air
heating, cooling, or fan.
Fig. 247.
5. Press Done to save the reminder.
6. Press Reset Timer when you have completed the rec-
ommended maintenance or you can extend the timer
setting to turn off the alert and remind you later to do
the recommended maintenance.
7. Repeat these steps for all reminders you want to set.
CUSTOMIZABLE REMINDERS
The thermostat can be set to alert the user when it is time
for system maintenance or warranty renewal. You can set
up to 10 total Custom Reminders on the thermostat and
save them to a microSD card for easy download to multiple
thermostats.
Custom Reminders include:
• Service Reminder
— Set up for recurring or one time only.
• Spring Service Reminder
— Provide an alert based on date or outdoor tem-
perature.
• Fall Service Reminder
— Provide an alert based on date or outdoor tem-
perature.
• Warranty Reminder
— Set up for recurring or one time only.
• New Custom Reminder
— Enter new reminders or advertisements
— Set up for recurring or one time only.
You can change or create custom reminders in ISU 1200.
Fig. 248.
For example, to set up a Fall Service Reminder based on
Outdoor Temperature:
1. Touch Press HERE to edit (see Fig. 248).
2. Select Fall Reminder and press Next.
Fig. 249.
3. Press up or down arrows until “Based on Out. Temp”
is displayed, then press Next.
Fig. 250.