VisionPRO 8000 Spec Sheet 2017
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
68-0312—05 26
219 External Fossil Fuel
Kit
No
Yes
No Both No This ISU is only displayed when ISU 201 Heating
Equipment is Air to Air Heat Pump, Geothermal or
Geothermal Radiant and ISU 218 Backup Heat
Type is Gas/Oil.
222 Economizer fault
“FDD”
No
Yes
No Commercial TH8321R
with no
EIM only
If using a TH8321R without EIM and your code
requires that the thermostat display an alert when
the economizer is sending a fault code, select
“Yes”. When this is done, the economizer will need
to be wired as shown in Fig. 339 on page 136. If
EIM used, and economizer fault required, this
option is not available. See Fig. 340 on page 136
222 Economizer Wiring
Thermostat terminal U1 Thermostat
terminal U1
Commercial TH8321R
with no
EIM only
Only shown if “economizer fault FDD” is set to yes.
This setting is to inform installer only. It is not
adjustable. See Fig. 339 on page 136.
222 A-L/A Terminal
None
Time Of Day
Economizer
Heat Pump Fault
Econ. Fault input
None
or
Econ. Fault input
Commercial No
“Econ.
Fault
input” for
TH8321R
with no
EIM only
This ISU is only displayed when ISU 101
Application is Commercial.
Note: When the thermostat is setup for Residential,
the L/A terminal operates as described under
"Heat Pump Fault". The L/A terminal requires no
setup for residential applications.
None: The A-L/A terminal is not used.
Time of Day: The A-L/A terminal is energized
during Occupied periods and when the user
overrides the temperature. The terminal is de-
energized during Unoccupied periods and in
Standby mode.
Economizer: The thermostat controls an
economizer module to provide ventilation during
Occupied periods and free cooling when outdoor
conditions are favorable. The
A-L/A terminal is energized during Occupied
periods and during a call for cooling in
Unoccupied periods. See “Economizer and Time of
Day (TOD) Operation” beginning on page 107.
Notes: The economizer module determines when
outdoor conditions are favorable for free cooling.
Heat Pump Fault: When 24 volts is detected on the
L/A terminal (compressor monitor), the thermostat
displays a message to alert the user when the heat
pump requires service. The L/A terminal sends a
continuous output to a zone panel when the
thermostat is set to Emergency Heat mode. The
zone panel will not turn on the heat pump when a
zone is set to Emergency Heat mode.
Econ. Fault input: Only shown if “Economizer fault
FDD” is set to “yes”. Not adjustable.
222 A-L/A terminal
Economizer fault
Commercial “Econ.
Fault
input” for
TH8321R
with no
EIM only
This ISU is only shown when the “Economizer fault
FDD” is set to “yes”. It is set for “economizer fault”
and is not adjustable. It is meant to inform the
installer that the A-L/A terminal needs to be wired
to the economizer as shown in Fig. 339 on page
136.
Table 2. Installer Setup (ISU) Table. (Continued)
ISU
Number
Installer Setup
Name Settings Default
Residential,
Commercial
or Both
Requires
EIM Notes