Non-Programmable Digital Thermostat Installation Instructions FocusPRO ® 5000 Series Wallplate installation Remove the wallplate from the thermostat, then follow directions below for mounting. 1. Remove battery holder. 2. Pull here to remove wallplate from new thermostat. 3. Pull wires through wire hole. 4. Position wallplate on wall, level and mark hole positions with pencil. 5. Drill holes at marked positions as shown below, then tap in supplied wall anchors. 6.
Power options Keep wires in this shaded area Remove factoryinstalled jumper only for twotransformer systems. Insert batteries for primary or backup power. Connect C for primary AC power (optional if batteries are installed). Wiring terminal designations Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.
Wiring conventional systems Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.
Wiring heat pump systems Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted. 1H/1C Heat Pump System Rc R Y C O/B G G Power [1] [R+Rc joined by jumper] Compressor contactor 24VAC common [3] Changeover valve [7] Fan relay 2H/1C Heat Pump System (TH5220D only) [8] Rc R Y C O/B G Aux/E L M29381 Rc R Y C O/B G Y2 L C Y R Rc Power [1] [R+Rc joined by jumper] Compressor contactor 24VAC common [3] Changeover valve [7] Fan relay Auxiliary/Emergency heat relay Sends output when set to Em.
Installer setup Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired. 1 1. To begin, press and hold the s and FAN buttons until the display changes. 2. Press s or t to change settings. 3. Press NEXT to advance to next function. 4. Press DONE to exit and save settings.
Setup function Settings & options (factory default in bold) Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.
Installer system test 1. To begin, press and hold the s and t buttons until the display changes. 2. Press s / t to turn system on/off. 3. Press NEXT to advance to next test 4. Press DONE to terminate system test. 1 10 System test number System test 0 M29388 System status System status Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted. 10 Heating system 0 1 2 3 20 Emergency heating 0 system 1 Heat and fan turn off. Stage 1 heat turns on.
Customer assistance For assistance with this product, please visit customer.honeywell.com. Or call Honeywell Customer Care tollfree at 1-800-468-1502. Pull at bottom to remove thermostat from wallplate. Turn thermostat over to find model number and date code. CAUTION: EQUIPMENT DAMAGE HAZARD Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly. CAUTION: ELECTRICAL HAZARD Can cause electrical shock or equipment damage.
Thermostat numérique non programmable Notice D’installation FocusPRO ® 5000 Série Installation de la plaque murale Séparer la plaque murale du thermostat comme, puis suivre les directives d’installation. 1. Retirer le porte-pile. 2. Tirer ici pour enlever la plaque murale du thermostat neuf. 3. Faire passer les fils par l’ouverture réservée aux fils. 4. Placer la plaque murale sur le mur, mettre de niveau et marquer au crayon l’emplacement des trous. 5.
Options d’alimentation Garder les fils dans cettezone ombragée Enlever le cavalier installé en usine uniquement pour les systèmes à deux transformateurs. Insérer les piles pour l’alimentation primaire ou de secours. M29370 Brancher C pour l’alimentation CA primaire (facultatif si des piles sont installées). Désignation des bornes Les zones ombragées ci-dessous s’appliquent seulement au TH5320U/ TH5220D ou selon les indications.
Guide de câblage – systèmes traditionnels Les zones ombragées ci-dessous s’appliquent seulement au TH5320U/ TH5220D ou selon les indications.
Guide de câblage – systèmes de thermopompes Les zones ombragées ci-dessous s’appliquent seulement au TH5320U/ TH5220D ou selon les indications.
Mode de configuration par l’installateur Suivre les directives ci-dessous pour configurer le thermostat pour qu’il corresponde au système de chauffagerefroidissement installé, et pour personnaliser son fonctionnement. 1 1. Pour commencer, appuyer sur les touches s et FAN les maintenir enfoncés jusqu’à ce que l’affichage change. 2. Appuyer sur la touche s ou t pour modifier les réglages. 3. Appuyer sur NEXT pour passer à la fonction suivante. 4. Appuyer sur DONE pour quitter et enregistrer réglages.
Fonctions Réglage et options (réglages de l’usine en gras) Les zones ombragées ci-dessous s’appliquent seulement au TH5320U/ TH5220D ou selon les indications.
Test du système par l’installateur 1. Pour commencer, enfoncer et tenir les touches s et t jusqu’à ce que l’affichage change. 2. Appuyer sur s / t pour activer ou désactiver le système. 3. Appuyer sur NEXT pour passer à l’essai suivant. 4. Appuyer sur DONE pour terminer l’essai du système. Test du système 1 10 Numéro de test du système 0 M29388 État du système État du système Les zones ombragées ci-dessous s’appliquent seulement au TH5320U/ TH5220D ou selon les indications.
Services à la clientèle Pour obtenir de l’aide avec ce produit, veuillez consulter le site customer. honeywell.com. ou vous adresser aux Services à la clientèle de Honeywell en composant le 1-800-468-1502. Tirer le thermostat par le bas pour le détacher de la plaque murale. Retourner le thermostat pour trouver le numéro de modèle et le code de date. MISE EN GARDE : RISQUE DE DOMMAGE MATÉRIEL Le système ne tient pas compte du temps d’arrêt minimal du compresseur pendant le test par l’installateur.
Termostato digital no programable Instrucciones para la instalación FocusPRO ® 5000 Series Instalación de la placa para pared Quite la placa para pared del termostato, y luego siga las instrucciones para el montaje. 1. Extraiga el soporte de la batería. 2. Hale de aquí para quitar la placa para pared del nuevo termostato. 3. Hale los cables a través del agujero para los cables. 4. Coloque la placa en la pared, nivele y marque las posiciones de los agujeros. 5.
Opciones de fuentes de energía Mantenga los cables en esta área sombreada Quite el puente instalado en la fábrica sólo en los sistemas con dos transformadores. Coloque las baterías para suministro de energía principal o de respaldo. M29370 Conecte C para suministrar corriente CA (opcional si las baterías están instaladas). Designación de terminales Las áreas sombreadas que aparecen abajo sólo se utilizan para los modelos TH5320U y TH5220D o según se indique.
Cableado: sistemas convencionales Las áreas sombreadas que aparecen abajo sólo se utilizan en el caso de los modelos TH5320U y TH5220D o según se indique.
Cableado: sistemas de bomba de calor Las áreas sombreadas que aparecen abajo sólo se utilizan en el caso de los modelos TH5320U y TH5220D o según se indique.
Configuración de instalación Siga el procedimiento que aparece a continuación para configurar el termostato a fin de que se corresponda con el sistema de calefacción y refrigeración instalado, y seleccione las funciones según lo desee. Done 1. Para comenzar, pulse y mantenga presionados los botones s y FAN hasta que cambie la pantalla. 2. Presione s o t para cambiar la configuración. 3. Presione NEXT para avanzar a la siguiente función. 4. Presione DONE para salir y guardar la configuración.
Funciones de la configuración Configuraciones y opciones (las que vienen desde la fábrica aparecen en negrita) Las áreas sombreadas que aparecen abajo sólo se utilizan en el caso de los modelos TH5320U y TH5220D o según se indique.
Prueba del sistema 1. Para comenzar, pulse y mantenga presionados los botones s y t hasta que cambie la pantalla 2. Presione s / t para encender o apagar el sistema. 3. Presione “NEXT” para avanzar hacia la próxima prueba. 4. Presione “DONE” para finalizar la prueba del sistema. 1 10 0 Número de prueba del sistema M29388 Estado del sistema Prueba del sistema Estado del sistema Las áreas sombreadas que aparecen abajo sólo se utilizan en el caso de los modelos TH5320U y TH5220D o según se indique.
Asistencia al cliente Para obtener asistencia relacionada con este producto, visite customer.honeywell.com. O comuníquese con el número gratuito del servicio de atención al cliente, llamando al 1-800-468-1502. Hale de la parte inferior para quitar el termostato de la placa para pared. Gire el termostato para ver el número de modelo y el código de fecha. PRECAUCIÓN: PELIGRO DE DAÑO EN EL EQUIPO Durante la prueba, se desactiva la protección del compresor.