McDonald’s HEMS II End User Operations Manual
Table of Contents Overview………………………………………………………………………...3 Navigation to Login Page from local or remote personal computer.…..……4 Local Personal Computer & Remote Personal Computer Login …………..5 Panel Face Mounted Display Local Login…..………………………………..6 Home Page……………………………………………………………………....7-12 HVAC Units…………………………………………………………………….13 Schedules & Holidays………………………………………………………….14-17 Data Logging and Trended Points…………………………………………….18 Electrical Demand Limiting Adjustments…………………………………….
Overview McDonald’s HEMS II Energy Management Control System & User Interface The McDonald’s HEMS II energy management and control system runs on a WEB -201™ (Java Application Control Engine). The WEB -201 is a compact, embedded controller/server platform. It combines integrated control, supervision, data logging, alarming, scheduling and network management functions with Internet connectivity and web serving capabilities in a small, compact platform.
Navigation to Login Page from Local or Remote Personal Computer location Open internet browser and enter store IP address here: To begin: First open your internet browser and enter the WEBs Unit IP address in the "address bar". The WEBs Unit IP address will be furnished to you by the installer of the system. Additionally, you may consider installing a short cut icon on your personal computer Desk Top that will direct you to the IP address of your system.
Navigation to Login Page from Local or Remote Personal Computer location Login Page The Login Page is where you enter your username (user) and password (pass). Then click the login icon. Please wait until the booting process completely loads, once it does, it will automatically route you to the Home Page. Note that the first time you access your system from any browser it could take several minutes to load the Home Page.
Below is the default Login Page from the Local Touch Screen located on the front of panel after unit has been powered “ON”or after the blank screen has been touched and unit returns to normal operation mode from power saving standby mode. Login Page The Login Page will be automatically populated with the Username & Password. Touch the Login icon once and the system will automatically route you to the Home Page.
Home Page The Home Page will display your systems current conditions with any active alarms.
Home Page – continued This area of Home Page shows the following: 1. Your store number and physical location. 2. Current outside air temperature. By touching or clicking on the CYAN colored area you will be directed to a trend log of accumulated outside temperature data. See page 18 of this document for more information on this. 3. Current time and date in the control system. 4.
Home Page – continued This area of Home Page shows the following: 1. 2. 3. 4. Current electrical peak demand and current electrical (KWH) consumption for the current month and current year. By touching or clicking on any CYAN colored area you will be directed to a trend log of accumulated electrical data. See page 18 of this document for more information on this. Current electrical demand set point. See page 19 of this document for more information this.
Home Page – continued This area of Home Page shows the following: 1. 2. 3. Current freezer and cooler temperatures. By touching or clicking on any numeric value you will be directed to a trend log of accumulated freezer or cooler temperature data. See page 18 of this document for more information on this. RED bullet light (next to Freezer or Cooler) indicates an alarm condition. No alarm condition and the light will be GREEN.
Home Page – continued This area of Home Page shows the following: 1. 2. 3. 4. 5. 6. Current Lighting controls. RED bullet lights next to a lighting zone name indicates the lighting zone is commanded OFF by the associated time of day schedule or photocell. GREEN indicates the lighting zone is commanded ON by the associated time of day schedule or photocell. The photocells and their set points are only associated with Parking Lot and Signage lighting zones.
Home Page – continued This area of Home Page shows the following: 1. 2. 3. 4. 5. 6. Current HVAC Units. RED bullet lights next to FAN indicate the HVAC Unit is commanded OFF by the associated time of day schedule. GREEN indicates the HVAC Unit is commanded ON by the associated time of day schedule. By touching or clicking on Kitchen Area, Dining Area or Playplace Area icons you will be directed to another page for additional information and set point adjustments.
HVAC Units This area of HVAC Unit page shows the following: 1. 2. 3. 4. 5. 6. Each HVAC Unit has a page similar to above associated with it. The current view is that of the Kitchen HVAC Unit (Kitchen RTU – Roof Top Unit).
Time of Day Schedules & Holidays for HVAC Units and Lighting Zones By touching or clicking on any HVAC Unit or Lighting Zone Schedule icon from the Home Page you will see the following: 1. 2. 3. 4. Each HVAC Unit and Lighting Zone has a separate and distinctive time of day schedule associated with it. In this case you are looking at the Kitchen HVAC Unit schedule. The green areas indicate the Occupied Schedule and the gray areas indicate an Unoccupied Schedule.
Time of Day Schedules & Holidays for HVAC Units and Lighting Zones - continued 1. 2. 3. By touching or left clicking your mouse on any green area of the schedule that section will then turn blue and you can edit it. Notice that Monday was touched or clicked on and the background color changed to blue for editing. You can drag your finger or mouse (double arrow) to a new Occupied start and/or stop time. In the case above the start was retained at 4am and the stop time has now been set to 6pm.
Time of Day Schedules & Holidays for HVAC Units and Lighting Zones- continued 1. By touching and holding your finger on any green area of the schedule or right clicking your mouse that section will then turn blue and you are presented with a drop down selection where you can: Delete the Event, Make an All Day Event, Apply the Schedule to M-F, Copy the Day to the next Day, Clear the Day or Clear the Week. This is very intuitive and easy to understand after just a few minutes.
Time of Day Schedules & Holidays for HVAC Units and Lighting Zones- continued 1. 2. By touching or clicking on the Special Events tab at the bottom left of the screen to can add and edit special events. The example above shows that on Sat December 25th of 2010 (Christmas) the schedule has been set to Unoccupied for the complete day. It is very easy and intuitive to add special events or holidays for any unit or lighting zone that has a schedule associated with it.
Data Logging and Trended Points 1. 2. 3. 4. 5.
Electrical Demand Limiting and Lighting Photocell Adjustments 1. 2. 3. You reach this page by touching or clicking on the Lighting or Electrical icons on the Home page. Demand set point is easily adjusted by touching or clicking on the plus or minus keys above. For retrofit sites a review of your past 12 months of utility bills will allow for a determination of what this value should be.
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 20
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 21
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 22
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 23
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 24
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 25
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 26
Embedded Touch Screen Operating Instructions McDonald’s HEMS II page 27
McDonald’s HEMS II page 28
McDonald’s HEMS II page 29
McDonald’s HEMS II page 30
McDonald’s HEMS II page 31
McDonald’s HEMS II page 32
McDonald’s HEMS II page 33
McDonald’s HEMS II page 34
McDonald’s HEMS II page 35
McDonald’s HEMS II page 36
McDonald’s HEMS II page 37
