evohome THR092HRT Installation und Bedienung
B Holen Sie das beste aus Ihrem evohome System heraus
Installation und Bedienung Holen Sie das Beste aus Ihrem evohome System heraus Vielen Dank, dass Sie sich für den drahtlosen evohome Heizkörperregler entschieden haben. Wenn Sie den Heizkörperregler in Ihr bestehendes evohome System einbinden, können Sie weitere Räume (Zonen) unabhängig voneinander regeln. Dabei lässt sich bei mehr Komfort zusätzlich Energie einsparen.
2 Holen Sie das beste aus Ihrem evohome System heraus
Installation und Bedienung 3 Holen Sie das Beste aus Ihrem evohome System heraus Folgen Sie diesen Anweisungen, um das evohome System einzurichten. Geräte, die mit Netzspannung versorgt werden, müssen von einem Fachmann installiert werden. Bevor Sie beginnen Prüfen Sie, ob Sie alle für Ihr System benötigten Geräte haben: Sie benötigen das evohome Bediengerät und für jeden Heizkörper einen Heizkörperregler.
4 Was im Paket ist Was im Paket ist 1 x Heizkörperregler mit Ventiladapter für Standardventile M30x1,5 1 x Danfoss Adapter-Set (RA, RAV, RAVL) 1 x Displayhalter 2 x Mignon Batterien AA Übersicht über den Heizkörperregler Zeigt an, dass der Raumsoll wert manuell geändert wurde Funk-Kommunikationsfehler Bediensperre Funk-Kommunikationsanzeige Funksignal (Feldstärke) Textanzeige (9 Zeichen) Menü-Taste Drehrad Batteriestatus Temperaturanzeige
Installation und Bedienung 5 Heizkörperregler in Betrieb nehmen Wenn Sie einen oder mehrere Heizkörperregler in Betrieb nehmen, müssen die Geräte zuerst mit dem evohome Bediengerät verbunden werden (Binding). Das Binding ist erforderlich, damit die Geräte miteinander kommunizieren können. Wenn ein Gerät mit dem evohome Bediengerät verbunden ist, wird das Binding (Verbindung) dauerhaft im Gerät gespeichert, auch bei Stromausfall.
Heizkörperregler in Betrieb nehmen 6 Schritt 1 Batterien einlegen und Heizkörperregler verbinden evohome Bediengerät Drehrad entfernen. Batteriedeckel öffnen und die bereitgestellten AA-Batterien einsetzen. 3 Deckel schließen und Abdeckung wieder anbringen. 4 Taste einmal drücken. KEIN BIND sollte erscheinen. 5 Taste 5 Sekunden lang gedrückt halten, bis BIND erscheint. 6 Taste einmal drücken. BINDING sollte erscheinen.
Installation und Bedienung 7 Schritt 2 Heizkörperregler installieren 1 2 Abhängig vom vorhandenen Thermostatventl wird eventuell einer der mitgelieferten Adapter benötigt: 1. Adapter auf das Heizkörperventil aufsetzen und festdrehen, bis es einrastet. 2. Falls notwendig, Adapter mit einer der mitgelieferten Schrauben sichern. 3 4 5 6 7 8 Raum (Zone) für den Heizkörperregler wählen. Schieber in Position "offen" stellen. Ventiladapter vom Heizkörperregler trennen.
8 Heizkörperregler in Betrieb nehmen Schritt 2 – Fortsetzung Batterien sichern Heizkörperregler sichern
Installation und Bedienung 9 Schritt 3 Funktest Signalstärke des Funksignals zwischen Heiz körperregler und evohome Bediengerät testen. Am Heizkörperregler für die gewählte Zone 1 Taste drücken. Der Name der Zone erscheint. 2 Taste ca. 5 Sekunden lang gedrückt halten. 3 Mit dem Drehrad FUNKTEST wählen. 4 Taste erneut drücken. In der Anzeige erscheint TEST. 5 Taste erneut drücken, um ein Testsignal an das evohome Bediengerät zu senden.
10 Heizkörperregler in Betrieb nehmen Erweiterte Einstellungen Grundeinstellungen Bei Bedarf lassen sich 12 Grundeinstellungen (Parameter) anpassen. Parameter ändern 1 Taste ca. 5 Sekunden lang gedrückt halten, bis Parameter 1 blinkt (linke Ziffer). 2 Mit dem Drehrad den gewünschten Parameter (linke Ziffer) wählen. 3 Taste drücken, um den Parameter zu bearbeiten (rechte Ziffer). 4 Mit dem Drehrad die gewünschte Einstellung (rechte Ziffer) wählen und mit der Taste bestätigen.
Installation und Bedienung 11 Parameter-Liste Parameter Bedeutung Einstellungen 1 Sprache Sprache einstellen 2 beleucht Hintergrundbeleuchtung 1 ... 6 2 = Deutsch* 0 = ausgeschaltet 1 = aktiviert* 3 Fens Zeit Dauer der Fensterfunktion Bei Fenstererkennung wird das Heizkörperventil für die eingestellte Dauer geschlossen.
12 Bedienung des Heizkörperreglers Bedienung des Heizkörperreglers Der Heizkörperregler regelt die Raumtemperatur entsprechend der Vorgaben des evohome Bediengeräts, ohne dass weitere Einstellungen am Heizkörperregler vorgenommen werden müssen. Manuelle Änderungen der Raumtemperatur können jederzeit direkt am Heizkörperregler vorgenommen werden.
Installation und Bedienung 13 Manuelle Temperaturänderung Manuelle Änderung der Raumsollwert-Temperatur Die Raumsollwert-Temperatur kann jederzeit mit dem Drehrad geändert werden. Die geänderte Raumsollwert-Temperatur ist bis zum nächsten Schaltpunkt gültig. Das Symbol zeigt an, dass die Temperatur manuell geändert wurde. Beim nächsten Schaltpunkt erlischt das Symbol.
14 Bedienung des Heizkörperreglers Anzeige des Raum-(Zonen-)Namens Raumname (Zonenname) am Heizkörperregler anzeigen 1 Taste drücken. 2 Der dem Heizkörperregler zugeordnete Raum-(Zonen-)name wird kurz angezeigt.
Installation und Bedienung 15 Automatische Überwachungsfunktionen Fensterfunktion Wenn Sie ein Fenster öffnen und die Temperatur dadurch sinkt, schließt der Heizkörperregler das Heizkörperventil um Energie zu sparen. Im Display erscheint window und das Symbol wird am evohome Bediengerät für diesen Raum angezeigt. Wenn die Temperatur wieder ansteigt, spätestens aber nach der eingestellten Zeit (Werkseinstellung: 30 Minuten), öffnet der Heizkörperregler das Heizkörperventil wieder.
16 Bedienung des Heizkörperreglers Notbedienung Notbedienung bei leeren Batterien Schieber in die offene Position bringen. Heizkörperregler vom Ventilaufsatz abziehen. 3 Heizkörperventil mit dem Stellrad am Ventilaufsatz von Hand bedienen: Gegen den Uhrzeigersinn = Ventil öffnen Im Uhrzeigersinn = Ventil schließen 1 2 Der Heizkörper wird nur warm werden, wenn die Heizung eingeschaltet ist.
Installation und Bedienung 17 Fehler und Behebung Problem/Anzeige Mögliche Ursache Behebung Batterien leer Batterien wechseln. Keine Funk-Kommunikation Funkverbindung zwischen Heizkörperregler und evohome Bediengerät prüfen (Funktest). Symbole blinken Binding wiederholen. Spannungsversorgung am evohome Bediengerät und am Heizkörperregler prüfen. kein sync Funkverbindung unterbrochen Funkverbindung zwischen Heizkörperregler und evohome Bediengerät prüfen. e1 sensor Gerät defekt Gerät tauschen.
Technische Daten 18 Technische Daten Typ Schutzklasse Funkkommunikation RX Klasse 2 Spannungsversorgung THR092HRT IP30 ISM (868.0...870.0 MHz) Reichweite: typisch 30 m innerhalb von Wohngebäuden Batterietyp LR6, AA, AM3 Alkaline 2 x 1,5 V Lithium 2 x 1,5 V NiMH 2 x 1,2 V Heizkörperanschluss Umgebungstemperatur Abmessungen Umgebungsbedingungen Luftfeuchtigkeit M30 x 1,5 0...50 °C 96 x 54 x 60 mm Für Wohnbereich, Geschäfts- und Gewerbebereich sowie Kleinbetriebe 10...
Installation und Bedienung Hinweise zur Sicherheit Entsorgung WEEE-Richtlinie 2012/19/EC Richtlinie über Elektro- und Elektronik-Altgeräte • Entsorgen Sie Verpackung und Produkt am Ende der Produktlebensdauer in einem entsprechenden Recycling-Zentrum. • Entsorgen Sie das Produkt nicht mit dem gewöhnlichen Hausmüll. • Verbrennen Sie das Produkt nicht. • Entfernen Sie die Batterien. • Entsorgen Sie die Batterien entsprechend den gesetzlichen Bestimmungen und nicht mit dem gewöhnlichen Hausmüll.
Binding und Funktest – Übersicht 20 Binding und Funktest – Übersicht Taste kurz drücken Anzeige: Rauminformation Taste ca.
Installation und Bedienung 21
evohome www.homexpertbyhoneywell.com Novar GmbH a Honeywell Company Gartenstraße 49 58511 Lüdenscheid DEUTSCHLAND Hotline-Support Mo.–Fr. von 08:00–19:00 Uhr und Sa. von 09:00–16:00 Uhr Tel. 0180 6 70 70 50* * 0,20 Euro pro Anruf aus dem dt. Festnetz. Kosten für Anrufe aus dem Mobilfunknetz betragen max. 0,60 Euro pro Anruf. Technische Änderungen, die zur Verbesserung dienen, sind vorbehalten. 50080336-002A © 2014 Honeywell International Inc.