Submittal Sheet

ManualsBrandsHoneywell ManualsCommercial Thermostats & ControlsWall Module, Temperature Only, Two-Wire Sylk

Table Of Contents

OPERATING GUIDE

63-2741-01

Zio

Lite

TOOL CONFIGURATION, NETWORK ACCESS,

SYLK™ CAPACITY, AND OPERATION

TR40/TR42

Contents

Tool Configuration ............................................................ 1

General Settings Tab (Fig. 1). .................................... 2

Categories and Parameters Tab (Fig. 4). ................... 5

Home Screen Options Tab (Fig. 6). ............................ 8

Occupancy and Override Tab (Fig. 7) ........................ 9

Fan Command Tab (Fig. 8) ........................................ 10

Password Tab (Fig. 9) ................................................. 11

Network access to Zio Lite fields ...................................... 12

Sylk Capacity .................................................................... 13

Operation .......................................................................... 14

TR42 Wall Module Keypad Contractor Configuration . 14

Tenant Operation of Zio Lite TR42 ............................. 15

TOOL CONFIGURATION

The Zio Lite is configured using the same SBusWallModule wiresheet block as the Zio and Zio Plus, which is located in the BuiltIn

folder in the HoneywellSpyderTool palette. The configuration wizard has been modified to include the new TR40/42 Zio Lite

models.

Because the Zio Lite functionality is a subset of the Zio, it is fairly easy to set up.

Add the SBusWallModule block to the wire sheet, right click on the block, and select Configure Properties to enter the

configuration wizard.

Summary of content (16 pages)

PAGE 1
Zio® Lite TOOL CONFIGURATION, NETWORK ACCESS, SYLK™ CAPACITY, AND OPERATION TR40/TR42 OPERATING GUIDE Contents Tool Configuration ............................................................ General Settings Tab (Fig. 1). .................................... Categories and Parameters Tab (Fig. 4). ................... Home Screen Options Tab (Fig. 6). ............................ Occupancy and Override Tab (Fig. 7) ........................ Fan Command Tab (Fig. 8) ........................................
PAGE 2
ZIO® LITE General Settings Tab (Fig. 1). Fig. 1. General Settings Tab. Change the name in Block Name if desired, and then choose the TR40/42 you plan to configure (Fig. 1).
PAGE 3
ZIO® LITE If you choose a TR40 type, you will have just the general settings tab to set up (Fig. 2). Fig. 2. General Settings tab. Choose the wall module address. This address must match the bus address on the wall module, which is configured using the dip switches on the back of the device. Enter the F/C wiresheet units (required on TR4X models) and any offset to the sensor values if desired. Click Finish, and you are done with configuration.
PAGE 4
ZIO® LITE For TR42 models (Fig. 3), you can also select International to reduce the amount of English in the tenant view if you plan to have many non-English speakers using the device. You can also choose to make Language an editable option for the tenant by checking the box. Contractor set up at the wall module remains in English with either selection. Fig. 3. General Settings tab.
PAGE 5
ZIO® LITE Categories and Parameters Tab (Fig. 4). Fig. 4. Categories and Parameters tab. Unlike the Zio, the Zio Lite has just two fixed categories (Sensors and Setpoint), and just a few parameters for the supported sensors and the temperature setpoint. It is not possible to create new categories or parameters. For ROOMTEMP, select the number of decimals you wish to show and then check the Viewable by Tenant box if you want the tenant to see this value in the MORE screen on the thermostat.
PAGE 6
ZIO® LITE About the MORE screen in Zio Lite The MORE screen in Zio Lite is accessed by one of the soft keys on the wall module. Normally, the tenant will have access to the room temperature and the setpoint, but if you have a model with humidity or CO2, you can also allow the tenant to view these by pressing the MORE softkey. If both softkeys are being used (Override and Fan are both active), then pressing the up and down arrow keys simultaneously will always access the MORE screen.
PAGE 7
ZIO® LITE The temperature setpoint can be displayed numerically or graphically on the Zio Lite, as shown. If Numerical is chosen, a number will be shown in the display. This could be either an absolute value, say 70, 72, etc., or a relative offset value, say +/-5. If Graphical is chosen, a graduated line graph will appear on the display with COOLER to the left and WARMER to the right. Pressing up or down will cause the cursor to move left and right.
PAGE 8
ZIO® LITE Home Screen Options Tab (Fig. 6). Fig. 6. Home Screen Options tab. Only one value can show up in the home screen at a time. You have a number of choices. Temp or Temp Setpoint are probably the most common choices, but you can also choose other values listed. If you choose not to check the View by Tenant box for any of these items, they will still show up on your home screen if you choose one of them in this Home Screen Options tab, including the scrolling function.
PAGE 9
ZIO® LITE Occupancy and Override Tab (Fig. 7) Fig. 7. Occupancy and Override Tab. Selecting “Enable Occupancy Override” will allow the user to override to a bypass time into the occupied mode. You can choose to “Use Network Bypass Time Only”, or use a timed override which is selectable in the drop down menu. There is no option to override into unoccupied mode on the TR42. The TR42 will always show the effective occupancy on the display.
PAGE 10
ZIO® LITE Fan Command Tab (Fig. 8) Click this tab if fan access is needed. Choose the fan type and default state of the fan. This set up is identical to the TR7X. Fig. 8. Fan Command tab.
PAGE 11
ZIO® LITE Password Tab (Fig. 9) If a password to the installer menu is desired, check the Password tab and choose a four digit password. Fig. 9. Fan Command tab. If no password is needed, skip this tab. WARNING There is no backdoor to accessing this password, so write it down and keep in a safe place, especially in stand alone applications. The password can only be accessed via this configuration tool. Click finish and you are done.
PAGE 12
ZIO® LITE NETWORK ACCESS TO ZIO LITE FIELDS Listed below are the fields that will be available as NCIs on Spyder. You can readily access these in the points folder for use in px pages, etc. All of these settings are also configurable directly in the wall module in the contractor setup menu, accessed by pressing both upper keys for five seconds. Table 1.
PAGE 13
ZIO® LITE SYLK CAPACITY How many Sylk Wall Modules are supported? Sylk Device Capacity is determined by Sylk memory (Proxy), Sylk power consumption and Sylk bandwidth. All of these are now dynamically determined in the Spyder Resource Usage view in the workbench, example shown in Fig. 10. Fig. 10. The Bandwidth for sylk devices can change depending on the number of messages being sent per minute (so it is highly dependent on number of parameters set up for TR71 and TR75).
PAGE 14
ZIO® LITE OPERATION TR42 Wall Module Keypad Contractor Configuration The TR42 allows many of the same configurations in the tool to be made at the device as well. Configuration changes made at the device are automatically uploaded to the Spyder and preserved. Remember to upload the Spyder application to the tool before making changes in the tool if you want to preserve configuration changes made at the wall module.
PAGE 15
ZIO® LITE Table 2. (Continued) S. No INSTALLER SET-UP FIELD 16 VIEW DEVICE NAME 17 VIEW TEMP UNITS 18 VIEW LANGUAGE 19 VIEW ROOMTEMP 20 VIEW HUMIDITY 21 VIEW CO2 22 VIEW TEMP SETPOINT 23 FIRMWARE REV RANGE VIEW or HIDE –DETERMINES IF VIEWABLE IN THE MORE MENU, AND SCROLLING SCREEN (IF CHOSEN). ANY ITEM CHOSEN AS HIDE WILL STILL SHOW UP IF IT IS CHOSEN AS THE HOME SCREEN VALUE. X.XX Simply scroll through each selection with the up/down keys, click EDIT to make the changes desired.
PAGE 16
ZIO® LITE By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees, arising out of, or resulting from, any modification to the literature by you. Automation and Control Solutions Honeywell International Inc.