UV100A Ultraviolet System OWNER’S GUIDE 69-1381-4
UV100A ULTRAVIOLET SYSTEM IMPORTANT Please read these instructions and keep them in your records. HOW YOUR ULTRAVIOLET AIR TREATMENT SYSTEM OR SURFACE TREATMENT SYSTEM WORKS Depending on installation, your Ultraviolet System can operate as an Air Treatment System or as a Surface Treatment System.
UV100A ULTRAVIOLET SYSTEM Surface Treatment System When installed next to the cooling coil of your system, your Ultraviolet Surface Treatment System prevents a high percentage of the growth of micro-organisms such as mold that may grow on duct surfaces, coils, and drain pans. Individual results depend on careful installation and maintenance. See Fig. 2. ENT ISSEM VERT les ING/A nue etendre ! WARN la peau .
UV100A ULTRAVIOLET SYSTEM BE SURE TO READ WARNINGS AND CAUTIONS BEFORE USING YOUR UV SYSTEM WARNING UV Light Hazard. Harmful to bare skin and eyes. Can cause temporary or permanent loss of vision. Never look at bulbs while illuminated. View illumination only through light indicator located on lamp handle. To prevent exposure to ultraviolet light, disconnect power to Ultraviolet System before servicing any part of heating and air conditioning system.
UV100A ULTRAVIOLET SYSTEM MERCURY NOTICE This device contains mercury in the sealed ultraviolet bulb(s). Do not place your used bulb(s) in the trash. Dispose of properly. Broken Bulb Cleanup. Do not use a household vacuum. Sweep debris (phosphor/glass) into a plastic bag and dispose of properly. Contact your local waste management authority for instructions regarding recycling and the proper disposal of old bulb(s).
UV100A ULTRAVIOLET SYSTEM HOW YOU CAN CHECK YOUR ULTRAVIOLET SYSTEM Your UV System is designed to prevent accidental contact with electrical voltage and with ultraviolet rays in the sealed unit⎯the ultraviolet lamp does not illuminate unless the base is mounted on your forced air system duct. It is recommended that every month you verify that your ultraviolet lamp is operating. View the bulb only through the lamp light indicator on the lamp handle. See Fig. 3.
UV100A ULTRAVIOLET SYSTEM HOW YOU CAN MAINTAIN YOUR UV SYSTEM You should regularly clean your UV System to maintain peak effectiveness of your air treatment or surface treatment system. Replace the ultraviolet bulb once a year. Quarterly Bulb Cleaning Bulb cleaning is recommended as routine maintenance four times a year or every three months. Use the UV Bulb Cleaning Reminder Schedule, Fig. 4, to help establish and track your regular cleaning schedule.
UV100A ULTRAVIOLET SYSTEM 3. Rotate your lamp handle counterclockwise and gently pull the lamp handle to remove the bulb. See Fig. 5. M22842 Fig. 5. Remove lamp bulb. 4. Holding the lamp handle, wipe the lamp glass using a soft cloth dampened with glass cleaner. If you touch the lamp glass with your hands, be sure to clean the area of any oils left from bare hands. See Fig. 6. M22844 Fig. 6. Clean glass with soft cloth. 5.
UV100A ULTRAVIOLET SYSTEM 6. 7. Dry bulb with a clean, dry cloth. Insert the bulb into the base with the lamp light indicator at the eleven o’clock position. Continue pushing and gently rotating counterclockwise until the lamp handle inserts fully into the base. See Fig. 8. M22848 Fig. 8. Position bulb for insertion back into the lamp base. 8. Rotate the lamp handle clockwise until it snaps into place with the lamp light indicator aligned with the raised button on the unit cover. See Fig. 9.
UV100A ULTRAVIOLET SYSTEM 9. 10. 11. Reconnect power to your UV System. Verify that your ultraviolet bulbs are operating by viewing only through the lamp light indicator on the lamp handle. Never look directly at your bulb while it is illuminated. Reconnect power to your heating and cooling system. Bulb Replacement Annual replacement of the bulb in your ultraviolet lamp is required to maintain effectiveness. 1. Obtain the correct replacement bulb/handle assembly or replacement bulb for your unit.
UV100A ULTRAVIOLET SYSTEM 5. If you have a SnapLamp™ handle, follow steps 5 and 6; otherwise, proceed to step 7. Grasp the SnapLamp™ handle in one hand and the lamp glass in the other and pull straight apart. See Fig. 10. M22852 Fig. 10. Disconnect lamp glass from SnapLamp™ handle. 6. Insert the new lamp glass into the SnapLamp™ handle by aligning the key and pushing straight together. See Fig. 11. M22854 Fig. 11. Replace lamp glass in SnapLamp™ handle. 7. 8. 9. 10. 11.
UV100A ULTRAVIOLET SYSTEM Limited Warranty Honeywell warrants this product, excluding bulbs, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.