Submittal Sheet

ManualsBrandsHoneywell ManualsDamper actuatorsOn-Off Actuator with Proof of Closure w/ Nema 4

Table Of Contents

PRODUCT DATA

65-0029-01

V4055F,G Fluid Power Actuator

with Manual Control

APPLICATION

The V4055F and G fluid power gas valve actuators are for use

with the V5055 valve for gas safety shutoff applications to

control the gas supply of commercial and industrial burners.

FEATURES

• Fast opening time of 13 seconds at 120 V, 60 Hz.

• Maximum closing time, is 1 second, which meets

approval body requirements.

• Unit available with FM approved proof of closure

switch.

• Red “OPEN” indicator attached to the actuator piston

will show if the valve is even slightly open; yellow

“SHUT” indicator on the valve stem will show only

when the gas valve is fully closed.

• Ambient temperature rating of -40°F to +150°F (-40°C to

+66°C).

• Valve and actuator may be mounted in any position.

• Optional, field-adjustable, spdt auxiliary switch, rated

at 112 hp (0.37 kW), may be added in the field.

• Standard enclosure meets NEMA 1 (IP30) general

purpose requirements.

• Red light indicates when valve is ready to open.

• Rocker switch allows manual operation of valve.

• Valve closes on power loss.

SPECIFICATIONS

Models:

V4055G Fluid Power Actuator with Manual Control-for use

with the V5055 valve. Provides ON-OFF control. Rated

for 5 PSI.

V4055F-Same as V4055G except: for use with V5055C

only. Meets UL and FM proof of closure

requirements.

Contents

Application ........................................................................ 1

Specifications ................................................................... 1

Operation .......................................................................... 2

Ordering Information ........................................................ 2

Installation ........................................................................ 3

Wiring ............................................................................... 5

Checkout and Service ...................................................... 5

Summary of content (8 pages)

PAGE 1
V4055F,G Fluid Power Actuator with Manual Control PRODUCT DATA FEATURES • Fast opening time of 13 seconds at 120 V, 60 Hz. • Maximum closing time, is 1 second, which meets approval body requirements. • Unit available with FM approved proof of closure switch. • Red “OPEN” indicator attached to the actuator piston will show if the valve is even slightly open; yellow “SHUT” indicator on the valve stem will show only when the gas valve is fully closed.
PAGE 2
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL Mounting Means: Actuator mounts directly to valve bonnet with 2 setscrews, positioned 90 angular degrees apart. Valve and actuator can be mounted in any position. Table 1. Auxiliary Switch And Valve-closed Indication Switch Ratings: 112 hp (0.37 kW)a LOAD 120 V 240 V Full Load 9.8 A 4.9A Locked Rotor 58.5 A 29.4 A a Mounting Dimensions: See Fig. 1. Maximum total connected power to both switches (if used) is 1800 VA.
PAGE 3
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL 2 6-3/4 (172) 3-23/32 (95) 1 ALLOW 4 INCHES (102 MM) CLEARANCE FOR ACTUATOR REMOVAL. 2 ADD 1/8 INCH (3 MM) TO DIMENSION FOR MODELS WITH NEMA 4 ENCLOSURE. 3 ADD 1/4 INCH (6 MM) TO DIMENSION FOR A MODELS WITH NEMA 4 ENCLOSURE.
PAGE 4
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL WARNING Explosion Hazard. Can cause explosion, serious injury or death. 1. Turn off gas supply before starting installation. 2. Disconnect power supply for valve actuator before beginning installation. 3. Install the valve so the arrow on the valve body points in the gas flow direction. Install Valve The actuator is mounted directly on the valve bonnet after the valve is installed in the gas supply line.
PAGE 5
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL Mount Actuator On Valve Adjust The Auxiliary Switch (If Used) Check the final position of the valve body to be sure that the actuator will be in the proper position when mounted on the valve. The auxiliary switch is adjustable throughout the stroke of the actuator. With the switch installed in the actuator, turn the adjusting screw (Fig.
PAGE 6
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL 7. 8. 9. 10. d. If the inside surfaces are clear of hydraulic fluid, clean the bonnet assembly and be sure to remove all hydraulic fluid from the inside and outside of the actuator mounting curb. This is the “cup-like” area around the valve stem. Avoid using a cleaning solution as it may damage the rubber seals used in the valve. If the valve bonnet assembly is in good condition and is not replaced, replace the bonnet seal.
PAGE 7
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL 7 65-0029—01
PAGE 8
V4055F,G FLUID POWER ACTUATOR WITH MANUAL CONTROL Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Registered Trademark © 2007 Honeywell International Inc. 65-0029—01 M.S. Rev.