Submittal Sheet

2
V5011A, B, D-H, J SINGLE SEATED VALVES
77-5315-1
Fig. 1. Typical Flow Characteristics.
100
90
80
70
60
50
40
30
20
10
0
0 1020 304050607080 90100
LIFT-PERCENT OF MAXIMUM
FLOW-PERCENT OF MAXIMUM
C7968
EQUAL %
CONTOURED
PLUG
LINEAR
PLUG
SPECIFICATIONS
Models:
See Table 1
Flow Characteristics:
Equal percentage or linear. See Figure 1 and Table 1.
Valve Pressure-Temperature Ratings:
See Figure 2
Dimensions:
See Table 2 and Figures 3 through 6
Close-off Ratings:
See Table 3 and Figures 7 and 8
NOTE: Close-off curves for V5011 Valves mated with
Honeywell ICD (Industrial) Type 05 direct acting
pneumatic actuators are shown in Figure 8. These
actuators provide no close-off advantage over a
13-in. diameter, 3/4-in. stroke MP953 Actuator.
Maximum Pressure Differential (at Full Open for Normal
Disc and Seat Life):
Teflon or composition disc [425F (218C) max]:
Water, two-position service: 50 psi (345 kPa)
Water, modulating service: 25 psi (172 kPa)
Water, quiet modulating service: 20 psi (138 kPa)
Steam, two-position service: 70 psi (483 kPa)
Steam, modulating service: 35 psi (241 kPa)
Metal-to-metal seating (See Table 1):
Water, two-position or modulating service: not
recommended
Steam, two-position or modulating service: 100 psi
(690 kPa)
Body Materials:
Screwed-end Valves: Bronze
Flanged-end Valves: Cast iron
Stem Travel:
1/2- through 3-in. Valves: 3/4 in. (19 mm)
4-, 5-, and 6-in. Valves: 1-1/2 in. (38 mm)
Trim Materials:
Stem: Stainless steel
Packing:
Teflon cone [water – 150 psi (1034 kPa), 240F (116C)
max; alternating hot and cold, 140F (60C) max] for
ANSI Class 125 flanged V5011A and B Valves and
[steam 100 psi (689 kPa) 337F (169C) max] for ANSI
Class 150 screwed V5011G and J Valves
Rubber or Teflon/rubber [water – 250 psi (1724 kPa), 250F
(121C) max; alternating hot and cold, 140F (60C) max]
for ANSI Class 150 screwed V5011F and H Valves
Teflon V-ring [water – 250 psi (1724 kPa), 250F (121C)
max; alternating hot and cold, 140F (60C) max] for
ANSI Class 250 V5011D and E Valves
Disc:
Screwed bodies: Removable Teflon
Flanged bodies: Composition
Disc Holder:
Screwed bodies: Brass
Flanged bodies: Cast iron
Plug:
Screwed bodies with Teflon disc: Contoured brass
Screwed bodies with metal-to-metal seating: Contoured
stainless steel
Flanged bodies: V-ported, skirt-guided bronze
Seat:
Screwed bodies: Brass (replaceable, screwed into body;
non-replaceable on V5011H, J)
Screwed bodies: Metal-to-metal stainless steel (plug and
seat replaceable as matched set; not available on
V5011H, J)
Flanged bodies: Bronze (replaceable, screwed into body)
Accessories:
Actuator and linkage:
Pneumatic, see Table 4
Electric, see Table 5
Repacking kits:
14003294-003: V5011A, F, and H, 1/2 through
1-1/4 inch Valves
14003295-003: V5011A, F, and H, 1-1/2 through
3 inch Valves
14003294-001: V5011C, G, and J, 1/2 through
1-1/4 inch Valves
14003295-001: V5011C, G, and J, 1-1/2 through
3 inch Valves
Valve Actuation:
V5011 Valves require actuation by pneumatic MP953
Actuators or Type 05 Actuators (Table 4), or by Versadrive
or electric/electronic Modutrol IV
motors (Table 5). Refer to Figures 9 through 13 for
actuator dimensions.